DIR-815
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date 1.0 May 25, 2010 Description DIR-815 Revision A1 Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface ................................................................................. i Manual Revisions ........................................................................... i Trademarks ...................................................................................... i Product Overview .............................................................. 1 Package Contents .........................................................................
Table of Contents Advanced Wireless Settings ............................................59 802.11n/b/g (2.4GHz) ...................................................59 802.11n/a (5GHz) ...........................................................60 Wi-Fi Protected Setup (WPS) ..........................................61 Advanced Network ............................................................63 UPnP ...................................................................................63 Internet Ping Block .
Table of Contents Troubleshooting ............................................................113 Wireless Basics ...............................................................117 What is Wireless? ...................................................................... 118 Tips................................................................................................ 120 Wireless Modes......................................................................... 121 Networking Basics ......................
Section 1 - Product Overview Product PackageOverview Contents D-Link DIR-815 Wireless N Dual Band Router Power Adapter Ethernet Cable CD-ROM Note: Using a power supply with a different voltage rating than the one included with the DIR-815 will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements t "O &UIFSOFU CBTFE $BCMF PS %4- NPEFN t *&&& O PS H XJSFMFTT DMJFOUT t *&&& B XJSFMFTT DMJFOUT t &UIFSOFU Computer with the following: t 8JOEPXT®, Macintosh, or Linux-based operating system t "O JOTUBMMFE &UIFSOFU BEBQUFS Web-based Configuration Utility Requirements Browser Requirements: t *OUFSOFU &YQMPSFS PS IJHIFS t 'JSFGPY PS IJHIFS t 4BGBSJ PS IJHIFS t $ISPNF PS IJHIFS Windows® Users: Make
Section 1 - Product Overview Introduction TOTAL PERFORMANCE Combines award winning router features and IEEE 802.11a/n/g wireless technology to provide the best wireless performance. TOTAL SECURITY The most complete set of security features including Active Firewall and WPA/WPA2 to protect your network against outside intruders. TOTAL COVERAGE Provides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage.
Section 1 - Product Overview Features t 'BTUFS 8JSFMFTT /FUXPSLJOH - The DIR-815 provides up to 300Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless router gives you the freedom of wireless networking at speeds 650% faster than 802.11g.
Section 1 - Product Overview Hardware Overview Connections 1 3 4 5 1 LAN Ports (1-4) 2 Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem. 3 Reset Button Pressing the Reset button restores the router to its original factory default settings. 4 Power Button Use this switch to power on/power off the device. 5 Power Receptor D-Link DIR-815 User Manual Connect 10/100 Ethernet devices such as computers, switches, and hubs.
Section 1 - Product Overview Hardware Overview WPS Button 1 1 WPS Button D-Link DIR-815 User Manual Press the WPS button for 1 second to initiate the WPS process. The button will flash blue while a WPS connection is being established. The button will light solid blue for 5 seconds when the device has successfully been added to the network.
Section 1 - Product Overview Hardware Overview LEDs 6 1 3 4 5 1 Power LED A solid green light indicates a proper connection to the power supply. This LED will light orange during a factory reset or reboot. A slow blinking orange LED indicates that the Router has crashed during bootup. 2 Internet LED A solid green light indicates the PPP negotiation has successfully completed. This LED blinks green during data transmission.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Unplug the modem’s power adapter. Shut down your computer. 3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router. 4.
Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: t %JTBCMF 61O1™ t %JTBCMF %)$1 t $IBOHF UIF -"/ *1 BEESFTT UP BO BWBJMBCMF BEESFTT PO ZPVS OFUXPSL 5IF -"/ QPSUT PO UIF SPVUFS DBOOPU BDDFQU a DHCP address from your other router. To connect to another router, please follow the steps below: 1.
Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet (WAN) port of the D-Link router. :PV NBZ OPX VTF UIF PUIFS -"/ QPSUT UP DPOOFDU PUIFS &UIFSOFU EFWJDFT BOE DPNQVUFST 5P DPOöHVSF ZPVS XJSFMFTT network, open a web browser and enter the IP address you assigned to the router.
Section 2 - Installation Getting Started The DIR-815 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. Insert the Quick Router Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP. The steps and screens are similar for the other Windows operating systems. If the CD Autorun function does not automatically start on your computer, go to Start > Run.
Section 3 - Configuration Configuration This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). :PV NBZ BMTP DPOOFDU VTJOH UIF /FU#*04 OBNF JO UIF BEESFTT bar (http://dlinkrouter). Enter Admin in the User Name field. Leave the password blank by default.
Section 3 - Configuration After logging into the router for the first time, the D-Link Easy Setup window will appear: Easy Setup: Click this radio button to configure your router settings using a step-by-step wizard. Refer to the following page for more information on how to use the Easy Setup method to configure your Router. Manual Setup: Click this radio button if you prefer to setup your router manually. Refer to “Setup” on page 20 for more information on how to configure your router manually.
Section 3 - Configuration Easy Setup :PV DBO VTF UIF &BTZ 4FUVQ GFBUVSF UP DPOöHVSF ZPVS 3PVUFS JG ZPV BSF QMBOOJOH UP VTF UIF 4UBUJD *1 %ZOBNJD *1 %)$1 PS 111P& method to connect to the Internet. The Easy Setup feature also allows you to specify whether WPA/WPA2 wireless encryption or no encryption will be implemented on your wireless network. Use the Internet Connection drop-down menu to select the type of Internet connection you will use.
Section 3 - Configuration If you are using DHCP to connect to the Internet, select Dynamic IP (DHCP) from the Internet Connection drop-down menu. Click /FYU to continue. If you selected Static IP, enter the network settings supplied by your Internet provider. Click /FYU to continue.
Section 3 - Configuration The next Easy Setup window is used to configure your Router’s wireless network settings: 1. Enter the name (SSID) you would like to assign to your wireless network in the Network Name (SSID) field. 2 Use the Enable Security Mode drop-down menu to select the wireless security method that you want to implement on your network. Easy Setup allows you to implement the WPA/WPA2 security method.
Section 3 - Configuration The following window appears when Easy Setup has completed, displaying a summary of your Internet and wireless settings. Click Save to save the configuration. The following window appears to indicate that the settings are being saved: When the Router has finished saving all the changes, the following window appears: Click the Return to login page button to return to the main login page.
Section 3 - Configuration Setup Internet This section allows you to configure your Router’s Internet settings. Internet The Internet Connection Setup Wizard provides a quick Connection method for configuring your Internet settings. To start Setup Wizard: the Internet Connection Setup Wizard, click the Internet Connection Setup Wizard button. Refer to “Internet Connection Setup Wizard” on page 21 for more information on how to use the Internet Connection Setup Wizard.
Section 3 - Configuration Internet Connection Setup Wizard Click the Internet Connection Setup Wizard button to start the Internet Connection Setup Wizard.
Section 3 - Configuration The following window appears, summarizing the steps required to complete the Internet Connection Setup Wizard: Click /FYU to continue. Create a new password and then click /FYU to continue. Select your time zone from the drop-down menu and then click /FYU to continue.
Section 3 - Configuration Select the type of Internet connection you use and then click /FYU to continue. If you selected DHCP Connection (Dynamic IP Address), you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click /FYU to continue. The Host Name is optional but may be required by some ISPs. The default host name is the device name of the router and may be changed.
Section 3 - Configuration If you selected PPPoE, enter your PPPoE username and password. If your ISP requires you to enter a PPPoE service name, enter the service name in the Service Name field. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Click /FYU to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
Section 3 - Configuration If you selected - 51, enter your L2TP username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and L2TP server addresses. Click /FYU to continue. If you selected Static, enter your network settings supplied by your Internet provider. Click /FYU to continue.
Section 3 - Configuration If you selected Russia PPTP (Dual Access), enter your PPTP username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Click /FYU to continue. If you selected Russia PPPoE (Dual Access), enter your PPPoE username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.
Section 3 - Configuration Click Connect to save your settings. The following window appears to indicate that the settings are being saved. When the Router has finished saving all the changes, the Setup> Internet window will open. Close your browser window and reopen it to test your Internet connection. It may take a few tries to initially connect to the Internet.
Section 3 - Configuration Manual Internet Connection Setup Access Point Check the Enabled Access Point Mode box if you want to Mode: disable NAT on the router and turn it into an Access Point. Internet Use the My Internet Connection is drop-down menu to Connection select the mode that the router should use to connect to Type: the Internet.
Section 3 - Configuration Manual Internet Connection Setup Static IP Select Static IP GSPN UIF ESPQ EPXO NFOV JG BMM UIF *OUFSOFU QPSU T *1 JOGPSNBUJPO JT QSPWJEFE UP ZPV CZ ZPVS *41 :PV XJMM OFFE to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
Section 3 - Configuration Manual Internet Connection Setup Dynamic IP (DHCP) Select Dynamic IP (DHCP) from the drop-down menu to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services such as Comcast and Cox. Host Name: The Host Name is optional but may be required by some ISPs. Leave blank if you are not sure.
Section 3 - Configuration Manual Internet Connection Setup PPPoE (Username/Password) Select PPPoE (Username/Password) GSPN UIF ESPQ EPXO NFOV JG ZPVS *41 VTFT B 111P& DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
Section 3 - Configuration MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended UIBU ZPV DIBOHF UIF EFGBVMU ."$ BEESFTT VOMFTT SFRVJSFE CZ ZPVS *41 :PV DBO VTF UIF $MPOF :PVS 1$ T .
Section 3 - Configuration Manual Internet Connection Setup PPTP Select PPTP (Point-to-Point Tunneling Protocol) GSPN UIF ESPQ EPXO NFOV JG ZPVS *41 VTFT B 1151 DPOOFDUJPO :PVS *41 XJMM provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic IP. PPTP IP Address: Enter the IP address (Static PPTP only).
Section 3 - Configuration .BYJNVN *EMF Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Time: Auto-reconnect. DNS Servers: The DNS server information will be supplied by your ISP (Internet Service Provider). MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU.
Section 3 - Configuration Manual Internet Connection Setup - 51 Choose - 51 -BZFS 5VOOFMJOH 1SPUPDPM JG ZPVS *41 VTFT B - 51 DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV XJUI B VTFSOBNF BOE password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. - 51 *1 "EESFTT Enter the L2TP IP address supplied by your ISP (Static only).
Section 3 - Configuration .BYJNVN *EMF Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Time: Auto-reconnect. DNS Servers: Enter the Primary and Secondary DNS Server Addresses (Static L2TP only). MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU.
Section 3 - Configuration Manual Internet Connection Setup Russia PPTP (Dual Access) Select PPTP (Point-to-Point Tunneling Protocol) GSPN UIF ESPQ EPXO NFOV JG ZPVS *41 VTFT B 1151 DPOOFDUJPO :PVS *41 XJMM provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. PPTP IP Address: Enter the IP address (Static PPTP only).
Section 3 - Configuration .BYJNVN *EMF Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Time: Auto-reconnect. DNS Servers: The DNS server information will be supplied by your ISP (Internet Service Provider). MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU.
Section 3 - Configuration Manual Internet Connection Setup Russia PPPoE (Dual Access) Select PPPoE (Username/Password) GSPN UIF ESPQ EPXO NFOV JG ZPVS *41 VTFT B 111P& DPOOFDUJPO :PVS *41 XJMM QSPWJEF ZPV with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
Section 3 - Configuration MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended UIBU ZPV DIBOHF UIF EFGBVMU .
Section 3 - Configuration Wireless Settings If you want to configure the wireless settings on your router using the wizard, click Wireless Connection Setup Wizard and refer to ““Wireless Connection Setup Wizard” on page 92. Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to “Add Wireless Device with WPS Wizard” on page 95.
Section 3 - Configuration Manual Wireless Settings O C H ()[ Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Schedule: Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click New Schedule to create a new schedule.
Section 3 - Configuration O B ()[ Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Schedule: Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click New Schedule to create a new schedule.
Section 3 - Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. Router Use this section to configure the Router’s local network Settings: settings. DHCP Server Use this section to configure the DIR-815’s built-in DHCP Settings: server settings. DHCP Displays information about the devices that have a DHCP Reservations reservation from the DIR-815.
Section 3 - Configuration Network Settings Router Settings Router IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility. Default Subnet Enter the Subnet Mask. The default subnet mask is Mask: 255.255.255.0. Host Name: Enter a Host Name to identify the DIR-815. Local Domain: Enter the Domain name (Optional).
Section 3 - Configuration Network Settings DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The DIR-815 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-815.
Section 3 - Configuration Network Settings DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. $IFDLCPY Check this box to enable the reservation. Computer Enter the computer name.
Section 3 - Configuration Advanced Virtual Server The DIR-815 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DIR-815 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DIR-815 are invisible to the outside world.
Section 3 - Configuration The Virtual Server window allows you to open a single port. If you would like to open a range of ports, refer to the next page. Enable Check the box on the left side to enable the Virtual $IFDLCPY Server rule. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Port Forwarding This will allow you to open a single port or a range of ports. &OBCMF $IFDLCPY Tick the checkbox on the left side to enable the Port Forwarding rule. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-815.
Section 3 - Configuration QoS Engine The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically. Enable QoS This option is disabled by default. Enable this option for Engine: better performance and experience with online games and other interactive applications, such as VoIP.
Section 3 - Configuration Network Filter Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from BDDFTTJOH UIF OFUXPSL :PV DBO FJUIFS NBOVBMMZ BEE B ."$ BEESFTT PS TFMFDU UIF ."$ BEESFTT GSPN UIF MJTU PG DMJFOUT UIBU BSF currently connected to the Broadband Router.
Section 3 - Configuration Website Filter Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. To use this feature select the appropriate Web Filtering option, enter the domain or website, and click Save Settings. Configure Web Select Turn OFF WEBSITE FILTERING, ALLOW computers Filtering: access to ONLY these sites, or DENY computers access to ONLY these sites from the drop-down menu.
Section 3 - Configuration Firewall Settings A firewall protects your network from the outside world. The DIR-815 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
Section 3 - Configuration Firewall Settings Firewall Rules Use the Firewall Rules section to create/modify firewall rules. &OBCMF $IFDLCPY Check the box on the left side to enable the firewall rule. Name: Enter a name to identify the firewall rule. Action: Use the drop-down menu to Allow or Deny transport of the data packets according to the criteria defined in the firewall rule. Source: Use the Source drop-down menu to specify the interface that connects to the source IP addresses of the firewall rule.
Section 3 - Configuration Protocol: Select the protocol of the firewall port (All, TCP, UDP, or ICMP). Port Range: Enter the first port of the range that will be used for the firewall rule in the top port range field and enter the last port in the field underneath. Select Schedule: Use the drop-down menu to schedule the time that the Firewall rule will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled.
Section 3 - Configuration Routing The Routing option is an advanced method of customizing specific routes of data through your network. Enable: To enable a route, check the box that is on the left side of the route. Interface: Use the drop-down menu to specify if the IP packet must use the WAN or LAN interface to transit out of the Router. Destination: Enter the IP address of the packets that will take this route.
Section 3 - Configuration Advanced Wireless Settings O C H ()[ Transmit Power: Set the transmit power of the antennas. Beacon Period: Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. RTS Threshold: This value should remain at its default setting of 2346. If inconsistent data flow is a problem, only a minor modification should be made.
Section 3 - Configuration Advanced Wireless Settings O B ()[ Transmit Power: Set the transmit power of the antennas. Beacon Period: Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. RTS Threshold: This value should remain at its default setting of 2436. If inconsistent data flow is a problem, only a minor modification should be made.
Section 3 - Configuration Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures. The process is just as easy, as depressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin-Code Method.
Section 3 - Configuration Add Wireless Click the Connect your Wireless Device button to start Wireless Connection Setup Wizard. This wizard helps you add wireless Station: devices to the wireless network. The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the PIN for the device, or ask you to press the configuration button on the device.
Section 3 - Configuration Advanced Network Enable UPnP: To use the Universal Plug and Play (UPnP™) feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals. WAN Ping: Unchecking the box will not allow the DIR-815 to respond to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.
Section 3 - Configuration IPv6 Use the IPv6 window to configure the mode that the Router will use to access an IPv6 Internet connection. My Internet Use the drop-down menu to select the IPv6 Connection is: Internet Connection mode.
Section 3 - Configuration IPv6 Static IPv6 Select Static IPv6 from the My IPv6 Connection is drop-down menu if your Router will use a static IPv6 address to connect to the Internet. WAN IPv6 Address Enter the address settings supplied by your Internet Settings: provider (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPv6 Displays the Router’s LAN Link-Local Address.
Section 3 - Configuration IPv6 Static IPv6 (Stateless) To configure the Router to use a Static IPv6 Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 Static IPv6 (Stateful) To configure the Router to use a Static IPv6 Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select the Stateful(DHCPv6) option from the drop-down Type: menu. IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your Start: local computers.
Section 3 - Configuration IPv6 DHCPv6 (Stateful) Select Static IPv6 from the My IPv6 Connection is drop-down menu if your Router will use a static IPv6 address to connect to the Internet. WAN IPv6 Address Enter the address settings supplied by your Internet Settings: provider (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPv6 Displays the Router’s LAN Link-Local Address.
Section 3 - Configuration IPv6 DHCPv6 (Stateful)- Stateless Autoconfiguration To configure the Router to use a Static IPv6 Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 DHCPv6 (Stateful)- Stateful Autoconfiguration To configure the Router to use a Static IPv6 Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select the Stateful(DHCPv6) option from the drop-down Type: menu. IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your Start: local computers.
Section 3 - Configuration IPv6 6to4 Select 6to4 from the My IPv6 Connection is drop-down menu if your Router will use an IPv6 to IPv4 tunnel to connect to the Internet. WAN IPv6 Address Enter the address settings supplied by your Internet Settings: provider (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPv6 Displays the Router’s LAN Link-Local Address. Link-Local Address: LAN Address Use this section to configure the IPv6 autoconfiguration Autoconfiguration settings.
Section 3 - Configuration IPv6 6to4- Stateless Autoconfiguration To configure the Router to use an IPv6 to IPv4 tunnel stateless autoconfiguration connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 6to4- Stateful (DHCPv6) Autoconfiguration To configure the Router to use an IPv6 to IPv4 tunnel stateful autoconfiguration connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select the Stateful(DHCPv6) option from the drop-down Type: menu.
Section 3 - Configuration IPv6 Link-local Only Select Link-local Only from the My IPv6 Connection is drop-down menu if your Router will use the IPv6 link local method to connect to the Internet. LAN IPv6 Displays the LAN IPv6 Link-Local address of the router. Address Settings: Click the Save Settings button to save any changes made.
Section 3 - Configuration IPv6 Firewall The DIR-815’s IPv6 Firewall feature allows you to configure which kind of IPv6 traffic is allowed to pass through the device. The DIR-815’s IPv6 Firewall functions in a similar way to the IP Filters feature. &OBCMF $IFDLCPY Check the box on the left side to enable the IPv6 firewall rule. Name: Enter a name to identify the IPv6 firewall rule.
Section 3 - Configuration Tools Admin This page will allow you to change the Administrator password and configure the authentication settings. This window also allows you to enable Remote Management, via the Internet. Admin Enter a new password for the Administrator Login Name. Password: The administrator can make changes to the settings.
Section 3 - Configuration Time The Time window allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone: Select the Time Zone from the drop-down menu. Enable Daylight Check this box if the country your are located in uses Saving: Daylight Saving time.
Section 3 - Configuration Email Settings The Email feature can be used to send the system log files and router alert messages to your email address. From Email This email address will appear as the sender when you Address: receive a log file or firmware upgrade notification via email. To Email Address: Enter the email address where you want the email sent. Email Subject: Enter the text that you want to appear in the subject line of the e-mail that is sent.
Section 3 - Configuration System This section allows you to manage the router’s configuration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created. Save Settings to Use this option to save the current router configuration Local Hard Drive: settings to a file on the hard disk of the computer you are using. First, click the Save button.
Section 3 - Configuration Firmware Use the Firmware window to upgrade the firmware of the Router and install language packs. If you plan to install new firmware, make sure the firmware you want to use is on the local hard drive of the computer. If you want to install a new language pack, make sure that you have the language pack available.
Section 3 - Configuration Dynamic DNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Section 3 - Configuration System Check Ping Test: The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping. Click Stop to stop sending Ping packets IPv6 Ping The IPv6 Ping Test is used to send IPv6 Ping packets to test Test: if a computer is on the Internet. Enter the IPv6 Address that you wish to Ping, and click Ping.
Section 3 - Configuration Schedules Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm. Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check "MM %BZ IST or enter a Start Time and End Time for your schedule.
Section 3 - Configuration Status Device Info This page displays the current information for the DIR-815. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Configuration Logs The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained.
Section 3 - Configuration Statistics The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DIR-815 on both the WAN, LAN ports and both the 802.11n/g (2.4GHz) and 802.11n/a (5GHz) wireless bands. The traffic counter will reset if the device is rebooted. Refresh: Click the Refresh button to refresh the Router’s traffic statistics. Reset: Click the Reset button to reset the Router’s traffic statistics.
Section 3 - Configuration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.
Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.
Section 3 - Configuration IPv6 The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.
Section 3 - Configuration Support D-Link DIR-815 User Manual 90
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-815 offers the following types of security: t 81" 8J 'J 1SPUFDUFE "DDFTT t 81" 8J 'J 1SPUFDUFE "DDFTT t 81" 14, 1SF 4IBSFE ,FZ t 81" 14, 1SF 4IBSFE ,FZ 8IBU JT 81" WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Section 4 - Security Wireless Connection Setup Wizard To run the Wireless Connection Setup Wizard, click the Wireless Connection Setup Wizard button in the Setup>Wireless Settings window.
Section 4 - Security Wireless Security Setup Wizard Check the .BOVBMMZ TFU ()[ CBOE /FUXPSL /BNF box to manually set your desired wireless network name for the 5GHz band. Type your desired wireless network name (SSID). Automatically: Select this option to automatically generate the router’s network key and click /FYU. Manually: Select this option to manually enter your network key and click /FYU. If you selected Automatically, the summary window will display your settings.
Section 4 - Security If you selected Manually, the following screen will appear. Enter the Wireless Security Password you would like to use for your wireless network and click /FYU to proceed to the next window. The summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings.
Section 4 - Security Add Wireless Device with WPS Wizard From the Setup > Wireless Settings screen, click Add Wireless Device with WPS. Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients.
Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish XJSFMFTT DPOOFDUJWJUZ CFGPSF FOBCMJOH FODSZQUJPO :PVS XJSFMFTT TJHOBM NBZ EFHSBEF XIFO FOBCMJOH FODSZQUJPO EVF UP UIF added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2 Click on Setup and then click Wireless Settings on the left side. 3.
Section 4 - Security $POöHVSF 81" 81" 1FSTPOBM 14, It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish XJSFMFTT DPOOFDUJWJUZ CFGPSF FOBCMJOH FODSZQUJPO :PVS XJSFMFTT TJHOBM NBZ EFHSBEF XIFO FOBCMJOH FODSZQUJPO EVF UP UIF added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2 Click on Setup and then click Wireless Settings on the left side. 3.
Section 4 - Security $POöHVSF 81" 81" &OUFSQSJTF 3"%*64 It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish XJSFMFTT DPOOFDUJWJUZ CFGPSF FOBCMJOH FODSZQUJPO :PVS XJSFMFTT TJHOBM NBZ EFHSBEF XIFO FOBCMJOH FODSZQUJPO EVF UP UIF added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2 Click on Setup and then click Wireless Settings on the left side. 3.
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 5 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your router and click Connect :PV DBO BMTP DPOOFDU CZ QVTIJOH UIF 814 button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Configure WPS The WPS feature of the router can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature of the router: 1. Click the Start button and select Computer from the Start menu. 2. Click the Network option.
Section 5 - Connecting to a Wireless Network 3. Double-click the DAP-1560. 4. Input the WPS PIN number (displayed in the WPS window on the Router’s LCD screen or in the Setup > Wireless Setup menu in the Router’s Web UI) and click Next.
Section 5 - Connecting to a Wireless Network 5. Type a name to identify the network. 6. To configure advanced settings, click the icon. Click Next to continue.
Section 5 - Connecting to a Wireless Network 7. The following window appears while the Router is being configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the DAP-1560 has been setup successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. 9. Click Close to complete WPS setup.
Section 5 - Connecting to a Wireless Network Using Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.
Section 5 - Connecting to a Wireless Network Configure Wireless Security It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network.
Section 5 - Connecting to a Wireless Network Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network $POOFDU 6TJOH 8$/ JO 8JOEPXT 7JTUB® The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up depends on whether you are using Windows Vista® to configure the router or third party software. When you first set up the router, Wi-Fi protection is disabled and unconfigured. To enjoy the benefits of Wi-Fi protection, the router must be both enabled and configured.
Section 5 - Connecting to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used. Open the Windows ® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks.
Section 5 - Connecting to a Wireless Network The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-815. Read the following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples. 8IZ DBO U * BDDFTT UIF XFC CBTFE DPOöHVSBUJPO VUJMJUZ When entering the IP address of the D-Link router (192.168.0.
Section 6 - Troubleshooting t $POöHVSF ZPVS *OUFSOFU TFUUJOHT t (P UP Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. t $MJDL UIF Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. t (P UP UIF Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 6 - Troubleshooting 8IZ DBO U * DPOOFDU UP DFSUBJO TJUFT PS TFOE BOE SFDFJWF FNBJMT XIFO DPOOFDUJOH UISPVHI NZ SPVUFS If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 6 - Troubleshooting :PV TIPVME TUBSU BU BOE XPSL ZPVS XBZ EPXO CZ FBDI UJNF 0ODF ZPV HFU B SFQMZ HP VQ CZ VOUJM ZPV HFU B GSBHNFOUFE packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link XJSFMFTT GBNJMZ PG QSPEVDUT XJMM BMMPX ZPV UP TFDVSFMZ BDDFTT UIF EBUB ZPV XBOU XIFO BOE XIFSF ZPV XBOU JU :PV XJMM CF BCMF to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics 8IBU JT 8JSFMFTT Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries. 8IP VTFT XJSFMFTT Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, office, business, D-Link has a wireless solution for it.
Appendix A - Wireless Basics 8IFSF JT XJSFMFTT VTFE Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Wireless Modes There are basically two modes of networking: t Infrastructure – All wireless clients will connect to an access point or wireless router. t Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DIR-815 wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless router.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click 0, (Windows® 7/Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter Setting. Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.
Appendix C - Technical Specifications Technical Specifications IEEE 802.11g: s -BPS s -BPS s -BPS s -BPS s -BPS s -BPS Standards s )%%% N DRAFT s )%%% G s )%%% B s )%%% A s )%%% s )%%% U s )%%% AB Security s 7%0TM s 70!TM - Personal/Enterprise s 70! TM - Personal/Enterprise Wireless Signal Rates1 IEEE 802.11n Draft 2.0: 20MHz Channel: s .SS -BPS MAX s .SS -BPS MAX 40MHz Channel: s .SS -BPS MAX s .
Appendix D - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: t .
Appendix E - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: t 0OMZ UP UIF QFSTPO PS FOUJUZ UIBU PSJHJOBMMZ QVSDIBTFE UIF QSPEVDU GSPN % -JOL PS JUT BVUIPSJ[FE SFTFMMFS PS EJTUSJCVUPS BOE t 0OMZ GPS QSPEVDUT QVSDIBTFE BOE EFMJWFSFE XJUIJO UIF öGUZ TUBUFT PG UIF 6OJUFE 4UBUFT UIF %JTUSJDU PG $PMVNCJB 6 4 1PTTFTTJPOT or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix E - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix E - Warranty to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the defective portion of the product and will not ship back any accessories.
Appendix E - Warranty PURCHASER OF THE PRODUCT. Limitation of Liability: 50 5)& ."9*.6. &95&/5 1&3.*55&% #: -"8 % -*/, *4 /05 -*"#-& 6/%&3 "/: $0/53"$5 /&(-*(&/$& 453*$5 -*"#*-*5: 03 05)&3 -&("- 03 &26*5"#-& 5)&03: '03 "/: -044 0' 64& 0' 5)& 130%6$5 */$0/7&/*&/$& 03 %".
Appendix F - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Note to US model owner: To comply with US FCC regulation, the country selection function has been completely removed from all US models. The above function is for non-US models only. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules.
uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
