DSL-2730E User Manual
DSL-2730E User Manual FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
DSL-2730E User Manual Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC - PART 68 This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:3P7DL01B2750EV1. If requested, this number must be provided to the telephone company.
DSL-2730E User Manual Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
DSL-2730E User Manual Contents 1 Introduction ........................................................................................................ 1 1.1 Packing List ........................................................................................... 1 1.2 Safety Precautions ................................................................................ 1 1.3 LEDs and Interfaces .............................................................................. 2 1.4 System Requirements ....
DSL-2730E User Manual 3.4.6 3.5 3.6 Logout ....................................................................................... 88 Status................................................................................................... 88 3.5.1 Device Info ................................................................................ 88 3.5.2 Wireless Clients ........................................................................ 90 3.5.3 DHCP Clients .........................................
DSL-2730E User Manual 1 Introduction The DSL-2730E supports multiple line modes. With four 10/100 base-T Ethernet interfaces at the user end, the device provides high-speed ADSL broadband connection to the Internet or Intranet for high-end users like net bars and office users. It provides high performance access to the Internet with a downstream rate of 24 Mbps and an upstream rate of 1 Mbps. It supports IPV6. The device supports WLAN access, such as WLAN AP or WLAN device, to the Internet.
DSL-2730E User Manual Do not put this device close to a heat source or under a high temperature occurs. Keep the device away from direct sunshine. Do not put this device close to an overdamp or watery place. Do not spill fluid on this device. Do not connect this device to a PC or electronic product unless instructed by our customer engineer or your broadband provider. Wrong connection may cause power or fire risk. Do not place this device on an unstable surface or support. 1.
DSL-2730E User Manual LED Color Status Blinks WLAN Green normal. The WLAN connection is not established. Blinks DSL Blue WPS negotiation is enabled, waiting for the clients. WPS negotiation is not enabled on the Off Green interface. The connection of WLAN interface is On Off WPS Description Data is transmitted through the WLAN device. Off Initial self-test is failed. Blinks The device is detecting itself. Initial self-test of the unit has passed and On is ready.
DSL-2730E User Manual The following table describes the interface of the device. Interface/Button Description Antenna position RJ-11 interface that connects to the telephone set through DSL the telephone cable. LAN4/3/2/1 WPS Ethernet RJ-45 interfaces that connect to the Ethernet interfaces of computers or Ethernet devices. Press the button for 1 second to enable WPS function. WIRELESS ON/OFF ON/OFF Press the button silently to enable WLAN function. Power on or off the device.
DSL-2730E User Manual Multiple PVCs (eight at most) and these PVCs can be isolated from each other A single PVC with multiple sessions Multiple PVCs with multiple sessions Binding of ports with PVCs 802.1Q and 802.
DSL-2730E User Manual 2 Hardware Installation Step 1 Connect the DSL port of the device and the Modem port of the splitter with a telephone cable. Connect the phone to the Phone port of the splitter through a telephone cable. Connect the incoming line to the Line port of the splitter. The splitter has three ports: Line: Connect to a wall phone port (RJ-11 jack). Modem: Connect to the DSL port of the device. Phone: Connect to a telephone set.
DSL-2730E User Manual 3 Web Configuration This chapter describes how to configure the device by using the Web-based configuration utility. 3.1 Accessing the Device The following is the detailed description of accesing the device for the first time. Step 1 Step 2 Open the Internet Explorer (IE) browser and enter http://192.168.1.1. The Login page shown in the following figure appears. Enter the user name and password. The user name and password of the super user are admin and admin.
DSL-2730E User Manual 8
DSL-2730E User Manual 3.2 Setup In the main interface, click Setup tab to enter the Setup menu as shown in the following figure. The submenus are Wizard, Local Network, Internet Setup, Wireless Setup and Time and Date. 3.2.1 Wizard Wizard enables fast and accurate configuration of Internet connection and other important parameters. The following sections describe configuration parameters.
DSL-2730E User Manual There are 5 steps to configure the device. Click Next to continue. Step 1 Change the device login password. Step 2 Set the time and date. Step 3 Configure the Internet connection.
DSL-2730E User Manual If the internet service you subscribed is PPPoE or PPPoA, you can choose the Protocol to be PPPoE or PPPoA. Set the VPI and VCI. Enter the user name and password provided by your ISP.
DSL-2730E User Manual If the internet service you subscribed is Dynamic IP, you can choose Protocol to be Dynamic IP. The page shown in the following figure appears. If the Protocol is Static IP, you can choose Protocol to be Static IP. The page shown in the following figure appears. Enter the IP Address, Subnet Mask, Default Gateway and Primary DNS Server provided by your ISP.
DSL-2730E User Manual If the Protocol is Bridge, the page shown in the following figure appears.
DSL-2730E User Manual Step 4 Configure the wireless network. Step 5 Complete and apply the settings. Click Apply to save the settings.
DSL-2730E User Manual Note: In each step of the Wizard page, you can click Back to review or modify the previous settings. Click Cancel to exit the wizard page. 3.2.2 Local Network You can configure the LAN IP address according to the actual application. The preset IP address is 192.168.1.1. You can use the default settings and DHCP service to manage the IP settings for the private network. The IP address of the device is the base address used for DHCP.
DSL-2730E User Manual 3.2.2.1 LAN Interface Choose Setup > Local Network > LAN Interface. The LAN Setting page shown in the following figure appears. You may configure the LAN interface, for example, the IP address and subnet mask.
DSL-2730E User Manual The following table describes the parameters in this page. Field IP Address Description Enter the IP address of LAN interface. It is recommended to use an address from a block reserved for private use. This address block is 192.168.1.1- 192.168.1.254. Subnet Enter the subnet mask of LAN interface. The range of subnet Mask mask is from 255.255.0.0-255.255.255.254. Secondary Select it to enable the secondary LAN IP address.
DSL-2730E User Manual The following table describes the parameters of this page. Field Description Specify the LAN global ipv6 address. It can be Global Address Enable M Flag O Flag assigned by ISP. Enable or disable the Router Advertisement feature. Enable or disable the “Managed address configuration” flag in RA packet. Enable or disable the “Other configuration” flag in RA packet.
DSL-2730E User Manual Field Description specifies the dhcpv6 server address pool and other parameters. “Auto”: dhcpv6 server is opened and it use WAN dhcp-pd prefix to generate address pool. 3.2.2.3 DHCP Server Choose Setup > Local Network > DHCP Server. The DHCP Server Setting page shown in the following figure appears. You may configure the DHCP mode.
DSL-2730E User Manual The following table describes the parameters of this page. Field Description If set to DHCP Server, the router can assign IP DHCP Mode addresses, IP default gateway and DNS servers to the host in Windows95, Windows NT and other operation systems that support the DHCP client. It specifies the first and last IP addresses in the IP IP Pool Range address pool. The router assigns IP address in the IP pool range to the host.
DSL-2730E User Manual The following table describes the parameters and buttons in this page: Field IP Address Description It displays the IP address assigned to the DHCP client from the router. It displays the MAC address of the DHCP client. Each Ethernet device has a unique MAC address. MAC Address The MAC address is assigned at the factory and it consists of six pairs of hexadecimal character, for example, 00-A0-C5-00-02-12. It displays the lease time.
DSL-2730E User Manual In the DHCP Mode field, choose DHCP Relay. The page shown in the following figure appears. The following table describes the parameters and buttons of this page: Field Description If set to DHCP Relay, the router acts a surrogate DHCP Mode DHCP Server and relays the DHCP requests and Relay Server Enter the DHCP server address provided by your ISP. Apply Changes Click it to save the settings of this page. responses between the remote server and the client.
DSL-2730E User Manual 3.2.2.4 DHCP Reserved Choose Setup > Local Network > DHCP Reserved. The DHCP Static IP Configuration page appears. This page lists the fixed IP/MAC address on your LAN. The device distributes the number configured to hosts on your network as they request Internet access. The following table describes the parameters of this page. Field IP Address Mac Address Description Enter the specified IP address in the IP pool range, which is assigned to the host.
DSL-2730E User Manual 3.2.3 Internet Setup 3.2.3.1 Channel Config Choose Setup > Internet Setup > Channel Config. The Channel Configuration page appears. You may configure the parameters for the channel operation modes of your ADSL Router.
DSL-2730E User Manual The following table describes the parameters of this page. Field Default Route Description You can select Auto or Specified. Selection VPI The virtual path between two points in an ATM network, ranging from 0 to 255. The virtual channel between two points in an ATM VCI network, ranging from 32 to 65535 (1 to 31 are Encapsulation You can choose LLC and VC-Mux. reserved for known protocols) Channel Mode You can choose 1483 Bridged, 1483 MER, PPPoE, PPPoA, 1483 Routed or IPoA.
DSL-2730E User Manual Field Description user continuously, the router automatically disconnects the PPPoE connection. WAN IP Settings You can choose Fixed IP or DHCP. If select Fixed IP, you should enter the local IP address, remote IP address and subnet mask. Type If select DHCP, the router is a DHCP client, the WAN IP address is assigned by the remote DHCP server. Local IP Address Remote IP Enter the IP address of WAN interface provided by your ISP.
DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Protocol Description It displays the protocol type used for this WAN connection. ATM VCC The ATM virtual circuit connection assigned for Login Name The user name provided by your ISP. Password The password provided by your ISP. Authentication Method You can choose AUTO, CHAP, or PAP. this PPP interface (VPI/VCI). Connection Type You can choose Continuous, Connect on Demand, or Manual.
DSL-2730E User Manual Field Description PPPoE, or Disable Bridge. AC-Name The accessed equipment type. Service-Name The service name. 802.1q You can select Disable or Enable. After enable it, you need to enter the VLAN ID. The value ranges from 1 to 4095. Source Mac address The MAC address you want to clone. MAC Clone Click it to enable the MAC Clone function with the MAC address that is configured. Apply Changes Click it to save the settings of this page temporarily.
DSL-2730E User Manual Field VCI QoS Description The virtual channel identifier of the ATM PVC. The QoS category of the PVC. You can choose UBR, CBR, rt-VBR, or nrt-VBR. PCR Peak cell rate (PCR) is the maximum rate at which cells can be transmitted along a connection in the ATM network. Its value ranges from 1 to 65535. CDVT Cell delay variation tolerance (CDVT) is the amount of delay permitted microseconds). Its between value ATM ranges cells from 0 (in to 4294967295.
DSL-2730E User Manual 3.2.3.4 PVC Auto Search Choose Setup > Internet Setup > PVC Auto Search. The Auto PVC Configuration page appears. You may configure PVC auto detect function. Here you can add/delete auto PVC search table.
DSL-2730E User Manual 3.2.4 Wireless Setup This section describes the wireless LAN and basic configuration. A wireless LAN can be as simple as two computers with wireless LAN cards communicating in a pear-to-pear network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to wired LAN. 3.2.4.1 Wireless Basics Choose Setup > Wireless Setup > Wireless Basics. The Wireless Basic Settings page appears.
DSL-2730E User Manual The following table describes the parameters in this page. Description Field Choose the working mode of the modem. You can choose from the drop-down list. Band Choose the network model of the modem, which is Mode varied according to the software. By default, the network model of the modem is AP. The service set identification (SSID) is a unique name to identify the modem in the wireless LAN. Wireless SSID stations associating to the modem must have the same SSID.
DSL-2730E User Manual Click the button Show Active Clients to view the MAC address, transmission, reception packet counters and encrypted status for each associated wireless client. Click Apply Changes to save the settings. 3.2.4.2 Wireless Security Choose Setup > Wireless Setup > Wireless Security. The Wireless Security Settings page appears. Turn on WEP or WPA using encryption keys could prevent any unauthorized access to your wireless network.
DSL-2730E User Manual Field Description Configure the wireless encryption mode. You can choose None, WEP, WPA (TKIP), WPA (AES), WPA2 (AES), WPA2 (TKIP) or WPA2 Mixed. Wired equivalent privacy (WEP) encrypts data frames before transmitting over the wireless network. Encryption Wi-Fi protected access (WPA) is a subset of the IEEE802.11i security specification draft. WPA2 Mixed is the collection of WPA and WPA2 encryption modes.
DSL-2730E User Manual The following describes the parameters of this page: Field Key Length Description Choose the WEP key length. You can Choose 64-bit or 128-bit. If you choose 64-bit, you can choose ASCII (5 Key Format characters) or Hex (10 characters). If you choose 128-bit, you can choose ASCII (13 characters) or Hex (26 characters). Default Tx Key Choose the index of WEP Key. You can choose Key 1, Key 2, Key 3 or Key 4. The Encryption keys are used to encrypt the data.
DSL-2730E User Manual Field Description characters), enter any 13 ASCII characters. If you choose 128-bit and Hex (26 characters), enter any 26 hexadecimal characters. Click it to apply the settings temporarily. If you want Apply Changes to save the settings of this page permanently, click Save in the lower left corner. Click Apply Changes to save the settings. 3.2.5 Time and Date Choose Setup > Time and Date. The System Time Configuration page appears.
DSL-2730E User Manual Description Field Time Zone Select your local time zone from the dropdown list. Daylight Adjust the clock for daylight savings time. To synchronize the time automatically with the Internet Mode or your own computer, you may select Set Time Manually, Copy Computer Time or Set NTP Server Manually. Get GMT Time Synchronize to Greenwich Mean Time. When the mode is set to Set NTP Server Manually, the following page will appear.
DSL-2730E User Manual 3.3.1 Advanced Wireless This function is used to modify the standard 802.11g wireless radio settings. It is suggested not to change the defaults, as incorrect settings may reduce the performance of your wireless radio. The default settings provide the best wireless radio performance in most environments. 3.3.1.1 Advanced Settings Choose Advanced > Advanced Wireless > Wireless Advanced. The page shown in the following figure appears.
DSL-2730E User Manual Description Field Send Threshold) A packet of information that is sent from a connected device to all other devices where it announces its Beacon Interval availability and readiness. A beacon interval is a period of time (sent with the beacon) before sending the beacon again. The beacon interval may be adjusted in milliseconds (ms). Sets the wake-up interval for clients in power-saving DTIM Interval mode.
DSL-2730E User Manual Set the Wireless Access Control Mode to Allow Listed to enable white list function. Only the devices whose MAC addresses are listed in the Current Access Control List can access the modem. Set the Wireless Access Control Mode to Deny Listed to enable black list function. The devices whose MAC addresses are listed in the Current Access Control List are denied to access the modem. 3.3.1.3 WPS Choose Advanced > Advanced Wireless > WPS. The page shown in the following figure appears.
DSL-2730E User Manual There are two methods for the wireless client to establish connection with the modem through WPS. For one method, click Regenerate PIN to generate a new PIN, and then click Start PBC. In the wireless client tool, enter the PIN which is generated by the modem to start connection. The client will automatically establish the connection with the modem through the encryption mode, and you need not to enter the key. For the other method, the wireless client generates PIN.
DSL-2730E User Manual 3.3.1.4 MBSSID Choose Advanced > Advanced Wireless > MBSSID. The page shown in the following figure appears. In this page, you can set virutal access points (VAP), its SSID and authentication type. The device supports four virtual access points (VAPs). It is a unique name to identify the modem in the wireless LAN. Wireless stations associating to the modem must have the same name. Enter a descriptive name that is used when the wireless client is connecting to the modem.
DSL-2730E User Manual 3.3.2 Access Control List Multiple connections are required by some applications, for example, internet games, video conferencing and Internet telephony. These applications have difficulties working through NAT (Network Address Translation). This section is used to open multiple ports or a range of ports in your router and redirect data through those ports to a single PC on your network. 3.3.2.1 Access Control List Choose Advanced > Access Control List > Access Control List.
DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Direction Select LAN ACL Switch Description Select the router interface. You can select LAN or WAN. In this example, LAN is selected. Select it to enable or disable ACL function. Enter the IP address of the specified interface. Only IP Address the IP address that is in the same network segment with the IP address of the specified interface can access the router.
DSL-2730E User Manual Field Description to the Current ACL Table. Reset Click it to refresh this page. When the direction of data packets is set to WAN, the page shown in the following figure appears. The following table describes the parameters and buttons of this page: Field Direction Select WAN Setting WAN Interface Description Select the router interface. You can select LAN or WAN. In this example, WAN is selected. You can choose Interface or IP Address.
DSL-2730E User Manual Field Description You can choose the following services from WAN: Services Allowed Web, Telnet, SSH, TFTP, SNMP and PING. You can also choose all the services. After setting the parameters, click it to add an entry Add to the Current ACL Table. Reset Click it to refresh this page. 3.3.2.2 Access Control List IPv6 Choose Advanced > Access Control List > Access Control List IPv6. The page shown in the following figure appears. For configuration method, refer to 3.3.2.
DSL-2730E User Manual Click the Usual Application Name drop-down menu to choose the application you want to set up for port triggering. When you have chosen an application the default Trigger settings will populate the table below. If the application you want to set up isn’t listed, click the User-defined Application Name radio button and type in a name for the trigger in the Custom application field.
DSL-2730E User Manual 3.3.4 Port Forwarding This function is used to open ports in your device and redirect data through those ports to a single PC on your network (WAN-to-LAN traffic). It allows remote users to access services on your LAN, such as FTP for file transfers or SMTP and POP3 for e-mail. The device accepts remote requests for these services at your global IP address.
DSL-2730E User Manual 3.3.5 DMZ DMZ is the abbreviation of the Demilitarized Zone. Since some applications are not compatible with NAT, the device supports the use of a DMZ IP address for a single host on the LAN. This IP address is not protected by NAT and it is visible to agents on the Internet with the correct type of software. Note that any client PC in the DMZ is exposed to various types of security risks.
DSL-2730E User Manual 3.3.6.1 URL Block Choose Advanced > Parental Control > URL Block. The URL Block page shown in the following figure appears. You may deny certain websites from being accessed during the "schedule" you specified. Here you can add/delete filtered URL. Note: To use this feature, the time of router must be correct. Please set in 3.2.5 Time and Date. In the field Schedule Mode, you may select an existing schedule schedule for when the rule will be enabled, or manually set a schedule.
DSL-2730E User Manual 3.3.6.2 MAC Block Choose Advanced > Parental Control > MAC Block. The URL Block page shown in the following figure appears. You may block a LAN device connected to the router in the specified time section. In the field Rule Name, input a name that is meaningful to you, then enter a MAC address that you want to deny access to the Internet, and set the days and hours, and click Add Rule to add the MAC into the MAC Blocking Table. 3.3.6.
DSL-2730E User Manual In the field Rule Name, give the schedule a name that is meaningful to you, such as "Weekday rule". Set the Day(s) and time field, and click Add Rules to save the new rule in the following Rules Table. 3.3.7 Filtering Options Filters can be configured to manage your incoming and outgoing traffic. 3.3.7.
DSL-2730E User Manual Direction Upstream (Downstream) means packets outgoing (incoming) from (to) router. The Source IP addresses are LAN-side (WAN-side) addresses and the Destination IP addresses are WAN-side (LAN-side) addresses. Select the rule action, specify at least one of the following criteria: protocol, source/destination IP address, subnet mask and source/destination port. Click the Apply Changes to save a finished rule in the Rules List.
DSL-2730E User Manual For detailed configuration, you may refer to 3.3.7.1IP/Port Filter. 3.3.7.3 MAC Filter Choose Advanced > Filtering Options > MAC Filter. The MAC Filtering page shown in the following figure appears. You may create a list of MAC addresses that you would either like to allow or deny access to your network.
DSL-2730E User Manual 3.3.8 DoS Settings Denial-of-Service Attack (DoS attack) is a type of attack on a network that is designed to bring the network to its knees by flooding it with useless traffic. Choose Advanced > DoS Settings. The DOS Settings page shown in the following figure appears. Select the Enable DoS Prevention checkbox, select the options below, and click Apply Changes to finish.
DSL-2730E User Manual 3.3.9 DNS Domain Name System (DNS) is an Internet service that translates the URL/domain name into the corresponding IP address. Since URL/Domain Names are alphabetical, they are easier to remember. But the Internet is based on IP address. For example, the URL/Domain Name www.dlink.com is actually 192.168.0.123. 3.3.9.1 DNS Choose Advanced > DNS > DNS. The DNS Configuration page shown in the following figure appears. You may configure the ip addresses of DNS servers for DNS Relay.
DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Attain DNS Automatically Description Select it, the router accepts the first received DNS assignment from one of the PPPoA, PPPoE or MER enabled PVC(s) during the connection establishment. Set DNS Select it, enter the IP addresses of the primary and Manually secondary DNS server. Apply Changes Click it to save the settings of this page.
DSL-2730E User Manual The following table describes the parameters and buttons of this page. Field Attain DNS Automatically Set DNS Manually Interface Description Select it, the router accepts the first received DNS assignment from one of the PPPoA, PPPoE or MER enabled PVC(s) during the connection establishment. Select it, enter the IP addresses and choose the WAN interface of the primary, the secondary and the tertiary DNS server.
DSL-2730E User Manual set up with one of the supported DDNS service providers (DyndDNS.org or dlinkddns.com). Choose Advanced > Dynamic DNS. The Dynamic DNS Configuration page shown in the following page appears. The following table describes the parameters and buttons of this page. Field DDNS provider Hostname Description Select a dynamic DNS service provider from the pull-down list. Enter the host name that you registered with your DDNS service provider.
DSL-2730E User Manual Click Add to save the settings to the Dynamic DDNS Table. 3.3.11 Network Tools The router provides following tools: Port Mapping, IGMP Proxy, IP QoS, UPnP, SNMP, TR-069, Software Forbidden, ARP Binding and Client Limit. 3.3.11.1 Port Mapping Port Mapping supports a single (LAN) port or multiple (LAN) ports to be formed as a group and mapped to a PVC (which is associated w/ a VLAN).
DSL-2730E User Manual Follow the steps to manipulate a mapping group. Step 1 Step 2 Select a group from the table. Select interfaces from the available WAN and LAN interface groups and add it to the interface group list using the arrow buttons to manipulate the required mapping of the ports. Step 3 Click Apply button to save the changes.
DSL-2730E User Manual Note: The selected interfaces will be removed from their existing groups and added to the new group. 3.3.11.2 IGMP Proxy IGMP allows support for efficient multicasting -- transmission of identical content, such as multimedia, from a source to a number of recipients. IGMP proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts when you enable it.
DSL-2730E User Manual Field Query Interval Description The device sends query messages to check IGMP user periodically. The unit is second. Query Response The device waits for the IGMP user’s reply. The unit is Interval 100 * millisecond. The duration for the modem to cease forwarding Group Leave multicast packets after a corresponding IGMP "Leave Delay Group" message has been successfully offered to the modem. Click Apply Changes to save the settings. 3.3.11.
DSL-2730E User Manual Step 1 Enable IP QoS and click Apply to enable IP QoS function. Step 2 Click add rule to add a new IP QoS rule. The page shown in the following figure appears. The following table describes the parameters and buttons of this page.
DSL-2730E User Manual Field Description QoS Policy You can choose stream based, 802.1p based, or Schedule Mode You can choose strict prior or WFQ (4:3:2:1). DSCP based. Source IP The IP address of the source data packet. Source Mask The subnet mask of the source IP address. Destination IP The IP address of the destination data packet. Destination The subnet mask of the destination IP address. Mask Source Port The port of the source data packet.
DSL-2730E User Manual 3.3.11.5 SNMP SNMP (Simple Network Management Protocol) provides a means to monitor status and performance and set configuration parameters. It enables a management station to configure, monitor and receive trap messages from network devices. Choose Advanced > Network Tools > SNMP. The SNMP Protocol Configuration page shown in the following figure appears. You may change the settings for system description, trap ip address and community name.
DSL-2730E User Manual Description Field Select it to enable SNMP function. You need to Enable SNMP enable SNMP, and then you can configure the parameters of this page. Trap IP Address Enter the trap IP address. The trap information is sent to the corresponding host. Community Name The network administrators must use this password (Read-only) to read the information of this router.
DSL-2730E User Manual The following table describes the parameters of this page: Field Description ACS Configuration URL The URL of the auto-configuration server to connect to. User Name The user name for logging in to the ACS.
DSL-2730E User Manual Field Password Periodic Inform Enable Description The password for logging in to the ACS. Select Enable to periodically connect to the ACS to check configuration updates. Periodic Inform Specify the amount of time between Interval connections to ACS. Connection Request User Name The connection username provided by TR-069 Password The connection password provided by TR-069 service. service. Debug Show Message Select Enable to display ACS SOAP messages on the serial console.
DSL-2730E User Manual 3.3.11.7 Software Forbidden Choose Advanced > Network Tools > Software Forbidden. The Software Forbidden page shown in the following figure appears. You may config some software to be forbidden to deny the ip packets of it. To forbid one specified PC (or some PCs) from using an application, select the application you want to prohibit, and input a single IP address or IP addresses in range. When Single IP is selected, IP 0.0.0.0 represent for any IP.
DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description IP Address An IP address to be bound. Mac Address An MAC address to be bound. Add Click this icon to add an ARP binding. Delete Selected Delete a selected setting from the lsit. Undo Reconfigure the above setting. ARP Binding Table A list of all the current ARP binding settings. 3.3.11.9 Client Limit Choose Advanced > Network Tools > Client Limit.
DSL-2730E User Manual 3.3.12 Routing Under this menu, static route, default gateway and RIP type routing configurations can be performed. 3.3.12.1 Static Route Choose Advanced > Routing > Static Route. The Routing Configuration page shown in the following figure appears. This page is used to configure the routing information. You may add or delete IP routes.
DSL-2730E User Manual Field Description Enable Select it to use static IP routes. Destination Enter the IP address of the destination device. Subnet Mask Enter the subnet mask of the destination device. Next Hop Enter the IP address of the next hop in the IP route to the destination device. Metric The metric cost for the destination. Interface The interface for the specified route. Add Route Click it to add the new static route to the Static Route Table.
DSL-2730E User Manual 3.3.12.2 IPv6 Static Route Choose Advanced > Routing > IPv6 Static Route. The IPv6 Routing Configuration page shown in the following figure appears. This page is used to configure the routing information. You can add or delete IP routes. The following table describes the parameters and buttons of this page. Field Description Destination Enter the IPv6 address of the destination device. Prefix Length Enter the prefix length of the IPv6 address.
DSL-2730E User Manual Choose Advanced > Routing > IPv6 Static Route. The IPv6 Routing Configuration page shown in the following figure appears. The following table describes the parameters and buttons of this page: Field RIP Description Select Enable, the router communicates with other RIP-enabled devices. Apply Click it to save the settings of this page. Interface Choose the router interface that uses RIP. Choose the interface version that receives RIP messages. You can choose RIP1, RIP2, or Both.
DSL-2730E User Manual Field Description Add Click it to add the RIP interface to the Rip Config List. Delete Select a row in the Rip Config List and click it to delete the row. 3.3.13 NAT Under this menu, NAT ALG (Application Layer Gateway), NAT Exclude IP, NAT Forwarding, FTP ALG Config and NAT IP Mapping can be performed. 3.3.13.1 NAT ALG Choose Advanced > NAT > NAT ALG. The NAT ALG and Pass-Through page shown in the following figure appears.
DSL-2730E User Manual 3.3.13.3 NAT Forwarding Choose Advanced > NAT > NAT Forwarding. The NAT Forwarding page shown in the following figure appears. Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall. These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway's NAT firewall.
DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description Input a local IP address. Local IP Address Remote IP Input a remote IP address Address Enable Apply Changes Reset Current NAT Port Enable the current configured rule. Submit the configurations. Cancel the modification and reconfigure the settings. Current configuration rule list. Forwarding Table 3.3.13.
DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description FTP ALG port Set an FTP ALG port. Add Dest Ports Add a port configuration. Delete Delete a selected port configuration from the list. Selected DestPort 3.3.13.5 NAT IP Mapping Choose Advanced > NAT > NAT IP Mapping. The NAT IP Mapping page shown in the following figure appears.
DSL-2730E User Manual 3.4 Maintenance 3.4.1 System Choose Maintenance > System. The page shown in the following figure appears. In this page you can reboot your router or save your router configuration to a file on your computer in case you have to reset your router to factory default settings. You can restore your router settings from a previously saved configuration file. You may also reset your router to factory default settings.
DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Reset to default Description This option restores all configuration settings back to the settings that were in effect at the time the router was shipped from the factory. All settings will be lost. If you want to save your router configuration settings, use the Backup Settings option below. Save and reboot This will save all your settings and restart the router.
DSL-2730E User Manual 3.4.2 Firmware Update Choose Maintenance > Firmware Update. The page shown in the following figure appears. This page displays your device firmware version and information that will be helpfulfor D-Link technicians should you require any technical support. The procedure for updating the firmware is as follows. Step 1 Click Browse…to search the file. Step 2 Click Update Firmware to update the configuration file. Step 3 Wait for the router to reboot.
DSL-2730E User Manual password, the only solution is to reset your router to factory default settings and you will lose all your device configuration settings. The following table describes the parameters and buttons of this page: Field Root Description The root account is fixed, having full access to the Web-based management interface. User The user account has the previlege to view configuration settings and statistics and update the router's firmware. 3.4.
DSL-2730E User Manual The following table describes the parameter and button of this page: Field Description Host Enter the valid IP address or domain name. Ping Click it to start to Ping. 3.4.4.2 Ping6 Choose Maintenance > Diagnostics > Ping6. The page shown in the following figure appears. The target Address can be a domain or IPv6 address. The following table describes the parameter and button of this page: Field Description Target Address Enter an IP address for Ping6 diagnosis.
DSL-2730E User Manual The following table describes the parameters and buttons of this page. Field Description Host Enter the destination host address for NumberOfTries Number of repetitions. diagnosis. Timeout Put in the timeout value. Datasize Packet size. DSCP Differentiated Services Code Point, You should set a value between 0-63. MaxHopCount Maximum number of routes. Interface Select the interface. Traceroute Click start traceroute. 3.4.4.
DSL-2730E User Manual Click Start to start ADSL tone diagnostics. 3.4.4.5 Diag Test Choose Maintenance > Diagnostics > Diag Test. The page shown in the following figure appears. In this page, you can test the DSL connection. You can also view the LAN status connection and ADSL connection. 3.4.5 System Log Choose Maintenance > System Log. The page shown in the following figure appears. This section when enabled allows the system to begin logging events based on the selected log level.
DSL-2730E User Manual The router can only keep a limited number of log entries due to router memory constraints. If you have an external SYSLOG server, you may choose to configure external logging and all log entries will be sent to your remote server. The following table describes the parameters and buttons of this page. Field Error Description When the system is likely to result in a module abnormity, the system generates an Error log.
DSL-2730E User Manual 3.4.6 Logout Choose Maintenance > Logout. The page shown in the following figure appears. In this page, you can log out of the configuration page. 3.5 Status You can view the system information and monitor performance 3.5.1 Device Info Choose Status > Device Info. The page shown in the following figure appears. This page displays a summary overview of your router, including system information, DSL information, LAN Configuration, DNS information, WAN Configuration and so on.
DSL-2730E User Manual 89
DSL-2730E User Manual 3.5.2 Wireless Clients Choose Status > Wireless Clients. The page shown in the following figure appears. This table shows the MAC address, transmission, reception packet counters and encrypted status for each associated wireless client. 3.5.3 DHCP Clients Choose Status > DHCP Clients. The page shown in the following page appears. This page displays all client devices that obtain IP addresses from the device. You can view the host name, IP address, MAC address and time expired(s).
DSL-2730E User Manual 3.5.4 ADSL Driver Choose Status > ADSL Driver. The page shown in the following page appears. This page displays all ADSL statistics information, including link down or on, downstream and upstream, type, line coding and so on. 3.5.5 Statistics Choose Status > Statistics. The page shown in the following page appears. This is a summary of the number of packets that have passed between the WAN and the LAN since the router was last initialized.
DSL-2730E User Manual 3.5.6 Route Info Choose Status > Route Info. The page shown in the following page appears. This table shows a list of destination routes commonly accessed by your network.
DSL-2730E User Manual 3.6 Help In the main interface, click Help tab to enter the Help menu as shown in the following figure. This section provides detailed configuration information for the device. Click a link to view corresponding information.
