Version 1.
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date Description 1.00 November 26, 2015 Initial release Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface ................................................................................. i Product Overview .............................................................. 1 Package Contents ......................................................................... 1 System Requirements ................................................................. 2 Introduction ................................................................................... 3 Features.............
Table of Contents Time ....................................................................................76 Schedule ...........................................................................77 System Log ............................................................................78 Admin .....................................................................................79 System ...............................................................................81 Upgrade .................................
Section 1 - Product Overview Product PackageOverview Contents Wireless AC1200 Dual-Band Gigabit ADSL2+/VDSL2 Modem Router (DSL-2885A) Power Adapter Ethernet Cable DSL Microfilter/Splitter Phone Cable If any of the above items are missing, please contact your reseller. Note: Using a power supply with a different voltage rating than the one included with the DSL-2885A will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements Web-based Configuration Utility Requirements • An active account with an Internet Service Provider using one of the following connection types: • A VDSL/ADSL connection to a telephone line using the DSL port • A broadband device connected using the WAN port • A mobile broadband 3G/4G/LTE connection using a USB modem • 802.
Section 1 - Product Overview Introduction The D-Link DSL-2885A Wireless AC1200 Dual-Band Gigabit ADSL2+/VDSL2 Modem Router shares your DSL Internet connection over a blazing-fast Wireless AC connection using advanced AC beamforming technology to maximize the speed and range of your wireless signal to significantly outperform 802.11n and other 802.11ac devices. It also comes equipped with four Gigabit ports to provide speeds up to 10x faster than standard 10/100 ports.
Section 1 - Product Overview Features • Faster Wireless Networking - The DSL-2885A introduces Smart Connect, a new D-Link feature which when combined with an additional 5 Ghz antenna can provide up to a full 1200 Mbps* wireless connection with concurrent 801.11ac and 802.11n wireless clients . It also operates on both the 2.
Section 1 - Product Overview Hardware Overview Back Panel 1 1 2 3 DSL Port 2 3 4 5 6 7 Connect to an DSL-enabled telephone line and with the supplied microfilter/splitter. Gigabit LAN Ports (1-4) Connect Ethernet devices such as computers, switches, storage (NAS) devices and game consoles. Gigabit WAN Port Connect broadband Ethernet WAN devices. 4 USB 2.0 Port Connect a USB flash drive to share content , or connect it to a USB printer to share it on your network.
Section 1 - Product Overview Side Panel 1 2 3 1 USB 2.0 Port Connect a USB flash drive to share content , or connect it to a USB printer to share it on your network. 2 WPS Button Press to start the WPS process and automatically create a secure connection to a WPS client. 3 Wi-Fi Button Press and hold for 2 seconds to enable or disable Wi-Fi.
Section 1 - Product Overview Hardware Overview LEDs 1 Solid Green Solid Red 1 Power 2 WAN 3 LAN Ports 1-4 4 Wireless 2.4/5G 5 WPS 6 USB 1-2 7 DSL 8 Internet D-Link DSL-2885A User Manual 2 3 4 5 6 7 8 A solid green light indicates a proper connection to the power supply. A solid red light indicates a the device is booting or an error has occurred. Blinking Green A blinking green light indicates that backup mode is active.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, attic, or garage. Note: This installation section is written for users who are setting up their home Internet service with the DSL-2885A Wireless AC1200 Dual-Band Gigabit ADSL2+/VDSL2 Modem Router for the first time.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
Section 2 - Installation Manual Setup 1 Connect the supplied micro-filter to the telephone outlet. If you are using a telephone handset on the same outlet, connect it to the PHONE port on the micro-filter. Telephone Outlet PHONE Microfilter 2 Connect the phone cable from the DSL port on the microfilter to the DSL port of the modem router. Caution: - To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Section 2 - Installation 3 Plug the power adapter into your modem router and connect to an available power outlet or surge protector. Caution: - Use only the included power adapter with this product. Power Adapter DSL-2885A 4 Press the power button and verify that the power LED is lit. Allow one minute for the router to boot up. After the modem router has powered up, verify that the Power and DSL LEDs are both lit.
Section 2 - Installation 5 If you wish to use a wired connection, connect the Ethernet cable from a LAN port of the DSL-2885A to the Ethernet port on your computer. Ethernet Cable Computer 6 If you wish to use a wireless connection, the default Wi-Fi Networks are dlink-2885A-z and dlink-2885A5G-z. Select either one from your computer’s wireless utility and connect. Enter the default Wi-Fi password printed on the product label on the bottom of the DSL-2885A.
Section 3 - Getting Started Getting Started There are two ways you can configure your router to connect to the Internet and connect to your clients: • D-Link Setup Wizard - This wizard will launch when you log into the router for the first time. Refer to page "Setup Wizard" on page 15. • Manual Setup - Log into the router and manually configure your router. Refer to "Configuration" on page 22.
Section 4 - Configuration Name: Enter a custom name for this client. Vendor: Displays the vendor of the device. MAC Address: Displays the MAC address of the device. IP Address: Enter a specific IP address for this client. Reserve IP: Enable to reserve this IP address for this client. Parental Allow or Block access to the router. Control: Click Save when you are done.
In the Settings menu on the bar on the top of the page, click Internet to see the Click Advanced Settings... to expand the list and see all of the options. WAN Access Select whether the device should act as an xDSL Router or a Type: Residential Gateway. PVC: Use the default setting unless otherwise instructed by your ISP. Ether WAN Port: If you selected Residential Gateway, sselect the Ethernet port that will connect to the WAN. Use this setting if you do not intend to use the built-in DSL modem.
Section 4 - Configuration IPv4 Dynamic IP (DCHP) Select Dynamic IP (DHCP) to obtain IP address information automatically from your Internet Service Provider (ISP). Select this option if your ISP does not give you an IP address to use. Host Name: The host name is optional but may be required by some ISPs. Leave it blank if you are not sure. Primary DNS Enter the primary DNS server IP address assigned by your ISP. This Server: address is usually obtained automatically from your ISP.
Section 4 - Configuration Static IP Select Static IP if your IP information is provided by your Internet Service Provider (ISP). IP Address: Enter the IP address provided by your ISP. Subnet Mask: Enter the subnet mask provided by your ISP. Default Enter the default gateway address provided by your ISP. Gateway: Primary DNS Enter the primary DNS server IP address assigned by your ISP. Server: Secondary DNS Enter the secondary DNS server IP address assigned by your ISP.
Section 4 - Configuration PPPoE Select PPPoE if your Internet connection requires you to enter a PPPoE username and password. This information is provided by your Internet Service Provider (ISP). Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Reconnect Select either Always-on, On-Demand, or Manual. Mode: Address Mode: Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.
Section 4 - Configuration PPPoA Choose PPPoA if your Internet connection requires you to enter a PPPoA username and password. This information is provided by your Internet Service Provider (ISP). Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Reconnect Select either Always-on, On-Demand, or Manual. Mode: Address Mode: Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.
Section 4 - Configuration PPTP Choose PPTP (Point-to-Point-Tunneling Protocol ) if your Internet Service Provider (ISP) uses a PPTP connection. Your ISP will provide you with a username and password. PPTP Server IP Enter the PPTP server IP address provided by your ISP. Address: Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Reconnect Select either Always-on, On-Demand, or Manual.
Section 4 - Configuration Secondary DNS Enter the secondary DNS server IP address assigned by your ISP. Server: MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your ISP. Click Save when you are done.
Section 4 - Configuration L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your Internet Service Provider (ISP) uses a L2TP connection. Your ISP will provide you with a username and password. L2TP Server IP Enter the L2TP server IP address provided by your ISP. Address: Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Reconnect Select either Always-on, On-Demand, or Manual.
Section 4 - Configuration Secondary DNS Enter the secondary DNS server IP address assigned by your ISP. Server: MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your ISP. Click Save when you are done.
Section 4 - Configuration DSL On this page you can configure your DSL settings. If you are unsure, you can obtain these settings from your ISP. DSL Select whether to enable or disable each DSL modulation option. Modulation: Usually it is best to leave these at their defaults, unless otherwise instructed by your ISP. Click Save when you are done.
Section 4 - Configuration ATM On this page you can configure your Asynchronous Transfer Mode (ATM) settings. If you are unsure, you can obtain these settings from your ISP. Interface: Select the ATM interface from the drop-down menu. VPI: Enter the Virtual Path Indicator (0 - 255). VCI: Enter the Virtual Channel Indicator (32 - 65535). Latency: Select the latency from the drop-down menu. Encapsulation: Select the method of encapsulation provided by your ISP. You can select LLC or VCMUX.
Section 4 - Configuration PTM On this page you can configure your Packet Transfer Mode (ATM) settings. If you are unsure, you can obtain these settings from your ISP. Interface: Select the PTM interface from the drop-down menu. Latency: Select the latency from the drop-down menu.
Section 4 - Configuration IPv6 To configure an IPv6 connection, click the IPv6 link. To return to the IPv4 settings, click IPv4. My Internet Choose your IPv6 connection type from the drop-down menu. You Connection Is: will be presented with the appropriate options for your connection type. Click Advanced Settings... to expand the list and see all of the options. For Auto Detection refer to Auto Detection on page 43. For Static IPv6 refer to Static IPv6 on page 44.
Section 4 - Configuration Auto Detection Auto Detection mode (not Auto-Configuration mode) automatically detects IPv6 the connection method used by your Internet Service Provider (ISP). If your ISP provides an IPv6 service and Auto Detection failed to detect it, the user must manually select another IPv6 connection type (such as PPPoE, Auto Configuration, 6rd, DS-Lite etc.) Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature.
Section 4 - Configuration Static IPv6 Select Static IP if your IPv6 information is provided by your Internet Service Provider (ISP). Use Link-Local Enable or disable a link-local address. Address: IPv6 Address: If you disabled Use Link-Local Address, enter the address supplied by your ISP. Subnet Prefix If you disabled Use Link-Local Address, enter the subnet prefix Length: length supplied by your ISP. Default Enter the default gateway for your IPv6 connection.
Section 4 - Configuration Autoconfiguration Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless Type: DHCPv6. Router Enter the IPv6 address lifetime (in minutes). Advertisement Lifetime: Click Save when you are done.
Section 4 - Configuration Auto Configuration (SLAAC/DHCPv6) This is a connection method where the ISP assigns your IPv6 address when your router requests one from the ISP’s server. Some ISPs require you to make some settings on your side before your router can connect to the IPv6 Internet. DNS Type: Select either Obtain DNS server address automatically or Use the following DNS address. Primary DNS If you selected Use the following DNS address above, enter the Server: primary DNS server address.
Section 4 - Configuration Autoconfiguration Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless Type: DHCPv6. Router Enter the IPv6 address lifetime (in minutes). Advertisement Lifetime: Click Save when you are done.
Section 4 - Configuration PPPoE Select PPPoE if your Internet connection requires you to enter a username and password. This information is provided by your Internet Service Provider (ISP). PPPoE Session: Choose Share with IPv4 to re-use your IPv4 PPPoE username and password, or Create a new session. Username: If you selected Create a new session above, enter the PPPoE username provided by your ISP here.
Section 4 - Configuration LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN IPv6 Link- Displays the router’s LAN link-local address. Local Address: Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. IPv6 Address Assignment: Enable Automatic Enable or disable DHCP-PD for other IPv6 routers connected to the DHCP-PD in LAN: LAN interface. Note: This feature requires a smaller subnet prefix than /64 (i.e.
Section 4 - Configuration IPv6 in IPv4 Tunnel The user can configure the IPv6 connection to run in IPv4 Tunnel mode. IPv6 over IPv4 tunneling encapsulates IPv6 packets in IPv4 packets so that IPv6 packets can be sent over an IPv4 infrastructure. Remote IPv4 Enter the IPv4 remote address you will use. Address: Remote IPv6 Enter the IPv6 remote address you will use. Address: Local IPv4 Enter the IPv4 local address you will use. Address: Local IPv6 Enter the IPv6 local address you will use.
Section 4 - Configuration LAN IPv6 Link- Displays the router’s LAN link-local address. Local Address: Enable Enable or disable the Automatic IPv6 Address Assignment feature. Automatic IPv6 Address Assignment: Enable Enable or disable automatic DHCP-PD services. Automatic DHCP-PD in LAN: Auto Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless Configuration DHCPv6. Type: Router Enter the IPv6 address lifetime (in minutes). Advertisement Lifetime: Click Save when you are done.
Section 4 - Configuration 6rd In this section the user can configure the IPv6 6rd connection settings. Assign IPv6 Enter the IPv6 prefix. Prefix: Primary DNS Enter the primary DNS server address. Server: Secondary DNS Enter the secondary DNS server address. Server: Enable Hub and Enable if you want to minimize the number of routes to the Spoke Mode: destination by using a hub and spoke method of networking.
Section 4 - Configuration Enable Automatic Check to enable the Automatic IPv6 Address Assignment feature. IPv6 Address Assignment: Autoconfiguration Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless Type: DHCPv6. Router Enter the IPv6 address lifetime (in minutes). Advertisement Lifetime: Click Save when you are done.
Section 4 - Configuration Local Connectivity Only Local Connectivity Only allows you to set up an IPv6 connection that will not connect to the Internet. Enable ULA: Click here to enable Unique Local IPv6 Unicast Addresses settings. Use Default Checking this box will automatically configure the ULA prefix for ULA Prefix: the default setting. ULA Prefix: If you wish to choose your own ULA prefix, enter it here. Current IPv6 This section will display the current settings for your IPv6 ULA.
Section 4 - Configuration Wireless In the Settings menu on the bar on the top of the page, click Wireless to see the wireless configuration options. To configure the router’s guest zone, click the Guest Zone link. Refer to 59 for details. Click Advanced Settings... to expand the list and see all of the options. 2.4 GHz Status: Enable or disable the wireless frequency band. Wi-Fi Name Create a name for your wireless network using up to 32 characters.
Section 4 - Configuration Schedule: Use the drop-down menu to select the time schedule that the rule will be enabled on. The schedule may be set to Always Enable, or you can create your own schedules in the Schedules section. Refer to page 76 for more information. 5 GHz Channel Width: Select Auto 20/40 if you are using both 802.11n and non-802.11n wireless devices, or select 20 MHz if you are not using any 802.11n wireless clients.
Section 4 - Configuration Multiple SSID The guest zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones will be separate from your main wireless network. You may configure different zones for the 2.4 GHz and 5 GHz wireless bands. In the Settings menu on the bar on the top of the page, click Wireless, then click the Guest Zone link. Click Advanced Settings... to expand the list and see all of the options.
Section 4 - Configuration Network This section will allow you to change the local network settings of the router and to configure the DHCP settings. In the Settings menu on the bar on the top of the page, click Network. Click Advanced Settings... to expand the list and see all of the options. LAN IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1.
Section 4 - Configuration DHCP Lease Enter the length of time for the IP address lease in minutes. Time: Always Enable this feature to broadcast your networks DHCP server to LAN/ Broadcast: WLAN clients. UPnP: Enable or disable Universal Plug and Play (UPnP). UPnP provides compatibility with networking equipment, software and peripherals. IPv4 Multicast Enable to allow IPv4 multicast traffic to pass through the router from Stream: the Internet.
Section 4 - Configuration SharePort This page will allow you to set up access to files on an external USB device plugged into the router. You can do this through the local network or from the Internet using either a web browser or an app on your smartphone or tablet. In the Settings menu on the bar on the top of the page, click SharePort. Status: Check to enable the media server functions, allowing connected clients access to media files over the network.
Section 4 - Configuration Create User The Create User page allows you to manage your SharePort user accounts. The current list of user accounts will be displayed, along with their current permissions and access path. If they do not have an account set up, users will be restricted to guest access; only having access to the “Guest” folder on the media server. The router can store a maximum of ten accounts (including the “Admin” account).
Section 4 - Configuration Firewall Settings The router’s firewall protects your network from malicious attacks over the Internet. In the Features menu on the bar on the top of the page, click Firewall Settings. Click Advanced Settings... to expand the list and see all of the options. Enable DMZ: Enable or disable Demilitarized Zone (DMZ). This completely exposes the client to threats over the Internet, and is not recommended in ordinary situations.
Section 4 - Configuration IPSec (VPN): Allows multiple VPN clients to connect to their corporate network using IPSec. Some VPN clients support traversal of IPSec through NAT. This Application Level Gateway (ALG) may interfere with the operation of such VPN clients. If you are having trouble connecting with your corporate network, try turning this ALG off. Please check with the system administrator of your corporate network whether your VPN client supports NAT traversal.
Section 4 - Configuration IPv4/IPv6 Rules The IPv4/IPv6 Rules section is an advanced option that lets you configure what kind of traffic is allowed to pass through the network. To configure the IPv4 rules, from the Firewall Settings page click IPv4 Rules. To configure IPv6 rules, from the Firewall Settings page click IPv6 Rules. To return to the main Firewall Settings page, click Security Check. To begin, use the drop-down menu to select whether you want to ALLOW or DENY the rules you create.
Section 4 - Configuration Port Forwarding Port forwarding allows you to specify a port or range of ports to open for specific devices on the network. This might be necessary for certain applications to connect through the router. In the Features menu on the bar on the top of the page, click Port Forwarding. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column.
Section 4 - Configuration Virtual Server The virtual server allows you to specify a single public port on your router for redirection to an internal LAN IP Address and Private LAN port. To configure the virtual server, from the Port Forwarding page click Virtual Server. To return to the main Port Forwarding page, click Port Forwarding. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column.
Section 4 - Configuration Website Filter The website filter settings allow you to block access to certain web sites. You can either create a list of sites to block, or create a list of sites to allow (with all other sites being blocked). In the Features menu on the bar on the top of the page, click Website Filter. If you want to create a list of sites to block, select DENY computers access to ONLY these sites from the drop-down menu. All other sites will be accessible.
Section 4 - Configuration Static Routes The Static Routes section allows you to define custom routes to control how data traffic is moved around your network. In the Features menu on the bar on the top of the page, click Static Routes. To configure IPv6 rules, click IPv6 and refer to page 72 for more information. To return to the main IPv4 static routes page, click IPv4. If you wish to remove a rule, click on its trash can icon in the Delete column.
Section 4 - Configuration IPv6 To configure IPv6 rules, on the Static Routes page click IPv6. To return to the main IPv4 static routes page, click IPv4. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column. If you wish to create a new rule, click the Add Rules button. Click Save when you are done. If you edit or create a rule, the following options will appear: Name: Enter a name for the rule.
Section 4 - Configuration Dynamic DNS Most Internet Service Providers (ISPs) assign dynamic (changing) IP addresses. Using a dynamic DNS service provider, people can enter your domain name in their web browser to connect to your server no matter what your IP address is. In the Features menu on the bar on the top of the page, click Dynamic DNS. Enable Enabling dynamic DNS will reveal further configuration options. Dynamic DNS: Status: Displays the current dynamic DNS connection status.
Section 4 - Configuration IPv6 Host The IPv6 host settings are found at the bottom of the Dynamic DNS page. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column. If you wish to create a new rule, click the Add Rules button. Click Save when you are done. If you edit or create a rule, the following options will appear: Host Name: Enter the host name that you registered with your dynamic DNS service provider.
Section 4 - Configuration Management Time & Schedule Time The Time page allows you to configure, update, and maintain the correct time on the internal system clock. From here you can set the time zone, the Network Time Protocol (NTP) server, and enable or disable daylight saving time. In the Management menu on the bar on the top of the page, click Time & Schedule. Time Zone: Select your time zone from the drop-down menu. Time: Displays the current date and time of the router.
Section 4 - Configuration Schedule Some configuration rules can be set according to a pre-configured schedule. To create, edit, or delete schedules, from the Time page click Schedule. To return to the Time page, click Time. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column. If you wish to create a new rule, click the Add Rules button. Click Save when you are done.
Section 4 - Configuration System Log The router keeps a running log of events. This log can be sent to a Syslog server, and sent to your email address. In the Management menu on the bar on the top of the page, click System Log. Enable Logging Check this box to send the router logs to a SysLog Server. If this is to Syslog disabled, there will be no other options on this page. Server: Syslog Server IP Enter the IP address for the Syslog server.
Section 4 - Configuration Admin This page will allow you to change the administrator (Admin) password and enable remote management. In the Management menu on the bar on the top of the page, click Admin. Password: Enter a new password for the administrator account. You will need to enter this password whenever you configure the router using a web browser.
Section 4 - Configuration SSH / Telnet / If you want to allow router setup via the SSH, telnet, or TFTP protocols, TFTP: you can configure it here. For each protocol, click Enable Local Management to allow administrators to configure the network from within, and/or Enable Remote Management to allow administrators to configure the network from outside. If you enabled remote management, enter the remote port number that the router will use for that protocol. Click Save when you are done.
Section 4 - Configuration Upgrade This page will allow you to upgrade the router’s firmware or language pack, either automatically or manually. To manually upgrade the firmware or language pack, you must first download the relevant file from http://support.dlink.com. In the Management menu on the bar on the top of the page, click Upgrade. Firmware The current firmware’s version and date will be displayed.
Section 4 - Configuration Statistics On the Statistics page you can view the amount of packets that pass through the router on the WAN, LAN, and wireless segments. In the Management menu on the bar on the top of the page, click Statistics. You can view the Internet, LAN, Wi-Fi 2.4 GHz, or Wi-Fi 5 GHz by clicking on the respective tabs at the top. The graph will update in real time. To clear the information on the graph, click Clear. The traffic counter will reset if the device is rebooted.
Section 5 - Connecting to a Wireless Network Connect a Wireless Client to your Router WPS Button The easiest and most secure way to connect your wireless devices to the router is with WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a software utility with WPS) that you can press to connect to the DSL-2885A router.
Section 5 - Connecting to a Wireless Network Windows® 8 WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key (Wi-Fi password) being used. To join an existing network, locate the wireless network icon in the taskbar next to the time display.
Section 5 - Connecting to a Wireless Network You will then be prompted to enter the network security key (Wi-Fi password) for the wireless network. Enter the password into the box and click Next. If you wish to use Wi-Fi Protected Setup (WPS) to connect to the router, you can also press the WPS button on your router during this step to enable the WPS function.
Section 5 - Connecting to a Wireless Network Windows® 7 WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 5 - Connecting to a Wireless Network 3. Highlight the wireless connection with Wi-Fi name (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as the one on the wireless router.
Section 5 - Connecting to a Wireless Network WPS The WPS feature of the DSL-2885A can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature: 1. Click the Start button and select Computer from the Start menu. 2. Click Network on the left side.
Section 5 - Connecting to a Wireless Network 3. Double-click the DSL-2885A. DSL-2885A 4. Input the WPS PIN number (on the router label) in the Setup > Wireless Setup menu in the Router’s Web UI) and click Next.
Section 5 - Connecting to a Wireless Network 5. Type a name to identify the network. 6. To configure advanced settings, click the icon. Click Next to continue.
Section 5 - Connecting to a Wireless Network 7. The following window appears while the Router is being configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the router has been set up successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. 9. Click Close to complete WPS setup.
Section 5 - Connecting to a Wireless Network Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s wireless utility, please refer to the user manual of your wireless adapter for help connecting to a wireless network. Most wireless utilities will have a “site survey” option similar to the Windows Vista® utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.
Section 5 - Connecting to a Wireless Network WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2.
Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as the one on the wireless router.
Section 5 - Connecting to a Wireless Network Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network WPA/WPA2 It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPAPSK Wi-Fi password and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The Wi-Fi password must be exactly the same as on the wireless router.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DSL-2885A. Read the following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to these examples. 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link router (192.168.1.
Section 6 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 6 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or a URL.
Section 6 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business, or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when, and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power. This makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere, not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Don’t let your next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to the product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 Click on Start > Control Panel > Network and Internet > Network and Sharing Center. Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Windows® XP Click on Start > Control Panel > Network Connections.
Appendix B - Networking Basics Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DSL-2885A offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA (Wi-Fi Protected Access) • WPA2-PSK (Pre-Shared Key) • WPA-PSK (Pre-Shared Key) What is WPA? WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Appendix C - Technical Specifications Technical Specifications Device Interfaces • One RJ-11 xDSL port • 802.11 ac/n/g/b Wireless LAN • One 10/100/1000 Gigabit WAN port • Four 10/100/1000 Gigabit LAN ports • Two USB 2.0 ports Power Antenna Types • Three external removable MIMO antennas Storage Temperature • -20 to 70 °C (-4 to 158 °F) Standards • IEEE 802.11ac • IEEE 802.11n • IEEE 802.11g • IEEE 802.11b • IEEE 802.11a • IEEE 802.3 • IEEE 802.3u • IEEE 802.3ab • IEEE 802.3az • IEEE 802.
Appendix D - Regulatory Statements Regulatory Statements Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix D - Regulatory Statements RF Frequency Requirements This device is for indoor use only when using all channels in the 5.150 GHz-5.250 GHz, and 5.725 GHz-5.850 GHz frequency range. High power radars are allocated as primary users of the 5.150 GHz-5.250 GHz, 5.250 GHz-5.350 GHz, and 5.725 GHz-5.850 GHz bands. These radar stations can cause interference with and/or damage this device. It is restricted to indoor environments only.
Appendix D - Regulatory Statements Customer Information: (1) This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On bottom of this equipment is a label that contains, among other information, a product identifier of TBC. If requested, this number must be provided to the telephone company.
Appendix D - Regulatory Statements European Union: This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. For more information, please refer to the Declaration of Conformity. Notice of Wireless Radio LAN Usage in The European Community: • At the time of writing this addendum, some countries such as Italy, Greece, Portugal, and Spain have not allowed operation of radio devices in the 5 GHz bands, although operation of 2.4 GHz radio devices is allowed.
Appendix D - Regulatory Statements 2.4 GHz Wireless Frequency and Channel Operation in EEC Countries: Region Metropolitan Guadeloupe, Martinique, St Pierre et Miquelon, Mayotte Reunion et Guyane Rest of EU community Spectrum Regulation Europa Frankreich D-Link DSL-2885A User Manual Frequency Band 2400 - 2454 MHz 2454 - 2483.5 MHz Max output power (EIRP) 100 mW 100 mW indoor, 10 mW outdoor 2400 - 2483.5 MHz 2420 - 2483.5 MHz 100 mW 100 mW MHz, Europa (ETSI) 2400 - 2483.
Appendix D - Regulatory Statements 5 GHz Wireless Frequency and Channel Operation in EEC Countries: Allowable 802.11a Frequencies and Channels 5.15-5.25 GHz (Channels 36, 40, 44, 48) Countries Liechtenstein 5.15-5.25 GHz & 5.725-5.875 GHz (Channels 36, 40, 44, 48, 149, 153, 157, 161, 165, 169) Austria 5.15-5.35 GHz (Channels 36, 40, 44, 48, 52, 56, 60, 64) France 5.15-5.35 & 5.47-5.
Appendix D - Regulatory Statements European Community Declaration of Conformity: Česky [Czech] Dansk [Danish] Deutsch [German] Eesti [Estonian] English Español [Spanish] Ελληνική [Greek] Français [French] Italiano [Italian] Latviski [Latvian] Lietuvių [Lithuanian] Nederlands [Dutch] Malti [Maltese] Magyar [Hungarian] D-Link tímto prohlašuje, že tento DSL-2885A je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Appendix D - Regulatory Statements Polski [Polish] Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] Suomi [Finnish] Niniejszym D-Link oświadcza, że DSL-2885A jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. D-Link declara que este DSL-2885A está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Appendix D - Regulatory Statements Disposing of and Recycling Your Product ENGLISH EN This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed of in household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has reached the end of its life, some will accept products for free.
Appendix D - Regulatory Statements FRANÇAIS FR Ce symbole apposé sur le produit ou son emballage signifie que, conformément aux lois et règlementations locales, ce produit ne doit pas être éliminé avec les déchets domestiques mais recyclé. Veuillez le rapporter à un point de collecte prévu à cet effet par les autorités locales; certains accepteront vos produits gratuitement. En recyclant le produit et son emballage de cette manière, vous aidez à préserver l’environnement et à protéger la santé de l’homme.
Appendix D - Regulatory Statements ITALIANO IT La presenza di questo simbolo sul prodotto o sulla confezione del prodotto indica che, in conformità alle leggi e alle normative locali, questo prodotto non deve essere smaltito nei rifiuti domestici, ma avviato al riciclo. Una volta terminato il ciclo di vita utile, portare il prodotto presso un punto di raccolta indicato dalle autorità locali. Alcuni questi punti di raccolta accettano gratuitamente i prodotti da riciclare.
Appendix D - Regulatory Statements POLSKI PL Ten symbol umieszczony na produkcie lub opakowaniu oznacza, że zgodnie z miejscowym prawem i lokalnymi przepisami niniejszego produktu nie wolno wyrzucać jak odpady czy śmieci z gospodarstwa domowego, lecz należy go poddać procesowi recyklingu. Po zakończeniu użytkowania produktu, niektóre odpowiednie do tego celu podmioty przyjmą takie produkty nieodpłatnie, dlatego prosimy dostarczyć go do punktu zbiórki wskazanego przez lokalne władze.
Appendix D - Regulatory Statements MAGYAR HU Ez a szimbólum a terméken vagy a csomagoláson azt jelenti, hogy a helyi törvényeknek és szabályoknak megfelelően ez a termék nem semmisíthető meg a háztartási hulladékkal együtt, hanem újrahasznosításra kell küldeni. Kérjük, hogy a termék élettartamának elteltét követően vigye azt a helyi hatóság által kijelölt gyűjtőhelyre. A termékek egyes helyeken ingyen elhelyezhetők.
Appendix D - Regulatory Statements DANSK DK Dette symbol på produktet eller emballagen betyder, at dette produkt i henhold til lokale love og regler ikke må bortskaffes som husholdningsaffald, mens skal sendes til genbrug. Indlever produktet til et indsamlingssted som angivet af de lokale myndigheder, når det er nået til slutningen af dets levetid. I nogle tilfælde vil produktet blive modtaget gratis.
Appendix D - Regulatory Statements SVENSKA SE Den här symbolen på produkten eller förpackningen betyder att produkten enligt lokala lagar och föreskrifter inte skall kastas i hushållssoporna utan i stället återvinnas. Ta den vid slutet av dess livslängd till en av din lokala myndighet utsedd uppsamlingsplats, vissa accepterar produkter utan kostnad. Genom att på detta sätt återvinna produkten och förpackningen hjälper du till att bevara miljön och skydda människors hälsa.
