User's Manual

ManualsBrandsD-Link ManualsElectronicsWireless N Service Router

Unified Services Router User Manual

149

Symptom: Router can obtain an IP address, but PC is unable to load Internet pages.

Recommended action:

1. Ask your ISP for the addresses of its designated Domain Name System (DNS) servers.

Configure your PC to recognize those addresses. For details, see your operating system

documentation.

2. On your PC, configure the router to be its TCP/IP gateway.

11.2 Date and time

Symptom: Date shown is January 1, 1970.

Possible cause: The router has not yet successfully reached a network time server

(NTS).

Recommended action:

1. If you have just configured the router, wait at least 5 minutes, select

Administration >

Time Zone, and recheck the date and time.

2. Verify your Internet access settings.

Symptom: Time is off by one hour.

Possible cause: The router does not automatically adjust for Daylight Savings Time.

Recommended action:

1. Select

Administration > Time Zone and view the current date and time settings.

2. Click to check or uncheck ―Automatically adjust for Daylight Savings Time‖, then click

Apply.

11.3 Pinging to Test LAN Connectivity

Most TCP/IP terminal devices and firewalls contain a ping utility that sends an ICMP

echo-request packet to the designated device. The DSR responds with an echo reply.

Troubleshooting a TCP/IP network is made very ea sy by using the ping utility in your

PC or workstation.

11.3.1 Testing the LAN path from your PC to your

router

1. From the PC‘s Windows toolbar, select Start > Run.

2. Type ping <IP_address> where <IP_address> is the router‘s IP address. Example: ping

192.168.10.1.

3. Click OK.

Summary of content (75 pages)

PAGE 1
Unified Services Router User Manual Symptom: Router can obtain an IP address, but PC is unable to load Internet pages. Recommended action: 1. Ask your ISP for the addresses of its designated Domain Name System (DNS) servers. Configure your PC to recognize those addresses. For details, see your operating system documentation. 2. On your PC, configure the router to be its TCP/IP gateway. 11.2 Date and time Symptom: Date shown is January 1, 1970.
PAGE 2
Unified Services Router User Manual 4. Observe the display:  If the path is working, you see this message sequence: Pinging with 32 bytes of data Reply from : bytes=32 time=NN ms TTL=xxx  If the path is not working, you see this message sequence: Pinging with 32 bytes of data Request timed out 5.
PAGE 3
Unified Services Router  User Manual Verify that the network (subnet) address of your PC is different from the network address of the remote device.  Verify that the cable or DSL modem is connected and functioning.  Ask your ISP if it assigned a hostname to your PC. If yes, select Network Configuration > WAN Settings > Ethernet ISP Settings and enter that hostname as the ISP account name.  Ask your ISP if it rejects the Ethernet MAC addresses of all but one of your PCs.
PAGE 4
PAGE 5
Chapter 12. Credits Microsoft, Windows are registered trademarks of Microsoft Corp. Linux is a registered trademark of Linus Torvalds. UNIX is a registered trademark of The Open Group.
PAGE 6
Unified Services Router User Manual Appendix A. Glossary ARP Address Resolution Protocol. Broadcast protocol for mapping IP addresses to MAC addresses. CHAP Challenge-Handshake Authentication Protocol. Protocol for authenticating users to an ISP. DDNS Dynamic DNS. System for updating domain names in real time. Allows a domain name to be assigned to a device with a dynamic IP address. DHCP Dynamic Host Configuration Protocol.
PAGE 7
Unified Services Router User Manual PPPoE Point-to-Point Protocol over Ethernet. Protocol for connecting a network of hosts to an ISP without the ISP having to manage the allocation of IP addresses. PPTP Point-to-Point Tunneling Protocol. Protocol for creation of VPNs for the secure transfer of data from remote clients to private servers over the Internet. RADIUS Remote Authentication Dial-In User Service. Protocol for remote user authentication and accounting.
PAGE 8
PAGE 9
Appendix B. Factory Default Settings Feature Device login Internet Connection Local area network (LAN) Description Default Setting User login URL http://192.168.10.1 User name (case sensitive) admin Login password (case sensitive) admin WAN MAC address Use default address WAN MTU size 1500 Port speed Autosense IP address 192.168.10.1 IPv4 subnet mask 255.255.255.
PAGE 10
Unified Services Router User Manual Appendix C.
PAGE 11
Unified Services Router User Manual Appendix D. Log Output Reference Facility: System (Networking) Log Message DBUpdate event: Table: %s opCode:%d rowId:%d Severity Severity DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG Log Message BridgeConfig: too few arguments to command %s BridgeConfig: too few arguments to command %s sqlite3QueryResGet failed.Query:%s ddnsDisable failed sqlite3QueryResGet failed.Query:%s sqlite3QueryResGet failed.
PAGE 12
Unified Services Router nimfAdvOptSetWrap: user has changed MTU option nimfAdvOptSetWrap: MTU: %d nimfAdvOptSetWrap: old MTU size: %d nimfAdvOptSetWrap: old Port Speed Option: %d nimfAdvOptSetWrap: old Mac Address Option: %d nimfAdvOptSetWrap: MacAddress: %s Setting LED [%d]:[%d] For %s l2tpEnable: command string: %s nimfAdvOptSetWrap: handling reboot scenario nimfAdvOptSetWrap: INDICATOR = %d nimfAdvOptSetWrap: UpdateFlag: %d nimfAdvOptSetWrap: returning with status: %s nimfGetUpdateMacFlag: MacTable Flag
PAGE 13
Unified Services Router User Manual %s:DBUpdate event: Table: %s opCode:%d rowId:%d %s:%d SIP ENABLE: %s sipTblHandler:failed to update ifStatic sipTblHandler:failed to update Configport DEBUG DEBUG DEBUG DEBUG %s:%d SIP DISABLE: %s DEBUG %s:%d SIP SET CONF: %s DEBUG Failed to open %s: %s Failed to start sipalg DEBUG DEBUG Failed to stop sipalg DEBUG Failed to get config info DEBUG Network Mask: 0x%x DEBUG RTP DSCP Value: 0x%x DEBUG Need more arguments DEBUG Invalid lanaddr DEBUG Inval
PAGE 14
Unified Services Router User Manual pPrivSep: %s %s:DBUpdate event: Table: %s opCode:%d rowId:%d Re-Starting sshd daemon.... sshd re-started successfully. sshd stopped . failed query %s vlan disabled, not applying vlan configuration.. failed query %s failed query %s DEBUG no ports present in this vlanId %d failed query %s vlan disabled, not applying vlan configuration.. disabling vlan enabling vlan vlan disabled, not applying vlan configuration..
PAGE 15
Unified Services Router User Manual GetDnsFromIsp: %s IdleTimeOutFlag: %s IdleTimeOutValue: %d AuthMetho: %d executing %s ... %s removing %s from bridge%d... %s adding %s to bridge%d... %s DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG stopping bridge... restarting bridge...
PAGE 16
Unified Services Router User Manual %s: buffer overflow %s: value of %s in %s table is: %s DEBUG DEBUG Failed to clear vlan for %d Failed to set vlan entry for vlan %d Failed to set vlan entries, while enabling \ Failed to execute vlanConfig binary for port number %d Failed to execute vlanConfig binary for vlanId %d Failed to enable vlan Failed to disable vlan Failed to set vlanPort table entries, while \ Failed to enable vlan unknown vlan state threegMgmtInit: unable to open the database file %s threeg
PAGE 17
Unified Services Router User Manual pppoeMgmtTblHandler: NetMask: %s pppoeMgmtTblHandler: AuthOpt: %d pppoeMgmtTblHandler: Satus: %d pppoeEnable: ppp dial string: %s pppoeMgmtDBUpdateHandler: returning with status: %s pptpMgmtTblHandler: MtuFlag: %d DEBUG DEBUG DEBUG DEBUG xl2tpdStop failed writing xl2tpd.conf failed writing options.
PAGE 18
Unified Services Router User Manual l2tpMgmtTblHandler: UserName: %s DEBUG l2tpMgmtTblHandler: Password: %s DEBUG l2tpMgmtTblHandler: AccountName: %s DEBUG l2tpMgmtTblHandler: DomainName: %s l2tpMgmtTblHandler: Secret: not specified DEBUG l2tpMgmtTblHandler: Secret: %s l2tpMgmtTblHandler: dynamic MyIp configured DEBUG l2tpMgmtTblHandler: MyIp: %s l2tpMgmtTblHandler: ServerIp: %s l2tpMgmtTblHandler: StaticIp: %s l2tpMgmtTblHandler: NetMask: %s DEBUG DEBUG DEBUG DEBUG l2tpMgmtTblHandler: SplitTu
PAGE 19
Unified Services Router User Manual ERROR dhcpcMgmtTblHandler: dhclient enable failed dhcpcMgmtTblHandler: dhcpc release failed dhcpcMgmtTblHandler: dhcpc disable failed dhcpcMgmtDBUpdateHandler: failed query: %s dhcpcMgmtDBUpdateHandler: error in executing " ERROR DHCPv6 Client start failed. ERROR ERROR ERROR DHCPv6 Client stop failed.
PAGE 20
Unified Services Router User Manual Created EAP/PEAP context: OK DEBUG Deleted EAP/PEAP context: OK Upper EAP sent us: decision = %d method state = %d P2 decision=(%d); methodState=(%d) Writing message to BIO: ERROR. Encrypted (%d) bytes for P2 P2: sending fragment. P2: message size = %d P2: sending unfragmented message. DEBUG P1: Sending fragment. DEBUG P1: Total TLS message size = (%d) P1: sending unfragmented message.
PAGE 21
Unified Services Router User Manual Error rcvd. opCode %d. pCtx NULL. TLS message len changed in the fragment, ignoring. no data to send while fragment ack received. TLS handshake successful. Created EAP/TTLS context: OK Deleted EAP/TTLS context: OK No more fragments in message. ERROR Upper EAP sent us: method state = %d; decision = %d P2: sending fragment.
PAGE 22
Unified Services Router User Manual pFB->msgBuff is NULL. Error calculating binary. DEBUG DEBUG Error calculating binary. DEBUG adpDigestInit for SHA1 failed. adpDigestInit for SHA1 failed. DEBUG DEBUG E = %d DEBUG R = %d Could not initialize des-ecb DEBUG DEBUG adpDigestInit for MD4 failed. DEBUG adpDigestInit for SHA1 failed. adpDigestInit for SHA1 failed. Error converting received auth reponse to bin.
PAGE 23
Unified Services Router User Manual password change is not allowed for this user DEBUG completed writing the policy DEBUG completed writing the SA DEBUG completed writing the proposal block DEBUG cmdBuf: %s X509_DEBUG : Invalid Certificate for the generated" DEBUG X590_ERROR : Failed to create File '%s' DEBUG x509TblHandler DEBUG pCertType: %s DEBUG pRowQueryStr: %s DEBUG x509SelfCertTblHandler pRowQueryStr: %s %s:DBUpdate event: Table: %s opCode:%d rowId:%d DEBUG DEBUG umiRegister fai
PAGE 24
Unified Services Router User Manual pEapCtx == NULL or pPDU == NULL. received EAP pdu bigger than EAP_MTU_SIZE. received EAP pdu bigger than EAP_MTU_SIZE. state machine is in invalid state. unable to create method context. method ctxCreate failed. method profile set failed. ERROR Could not initialize des-ecb ERROR ERROR Error cleaning cipher context. ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR state machine is in invalid state.
PAGE 25
Unified Services Router User Manual Could not open database: %s CPU LOG File not found DEBUG DEBUG MEM LOG File not found cpuMemUsageDBUpdateHandler: update query: %s DEBUG Printing the whole list after inserting %s at %d(minute) %d(hour) %d(dayOfMonth) %d(month)" DEBUG adpCmdExec exited with return code=%d DEBUG %s op=%d row=%d DEBUG sqlite3_mprintf failed DEBUG sqlite3QueryResGet failed: query=%s Printing the whole list after delete %s at %d(minute) %d(hour) %d(dayOfMonth) %d(month)" DEBUG
PAGE 26
Unified Services Router User Manual Adding Dictionary Attribute '%s' DEBUG Adding Dictionary Value %s DEBUG Receiving attribute: %s Processing attribute: %s Processing attribute: %s Processing attribute: %s Processing attribute: %s radConfGet: " Added Server %s:%d with " Added Server %s:%d with " Default Timeout Set to %d Default Retry Count Set to %d %s - %s : %d Deleting Server %s:%d with " Adding RowId:%d to Server %s:%d with " rowIds: %d - %d Deleting Server %s:%d with " RADIUS Deconfigured DEBUG
PAGE 27
Unified Services Router User Manual Next Synchronization after" Next Synchronization after %d \ Primary is not available, " Secondary is not available, " DEBUG DEBUG DEBUG DEBUG ERROR ERROR ERROR ERROR DEBUG DEBUG DEBUG Unable to set debug for radAuth. Unable to set debug level for radAuth. ERROR: option value not specified Unable to initialize radius Invalid username, challenge or response Unable to set debug for radAuth. Unable to set debug level for radAuth.
PAGE 28
Unified Services Router User Manual timeout after semTake srcId=%d(%s) <-- destId=%d(%s) cmd=%d DEBUG memPartAlloc for %d size failed ERROR DEBUG ERROR Un-registerting component with Id %d failed to send ioctl request: dst(%d) <--src(%d) processed a reply dst(%d) <-- src(%d) request with no result option dst(%d) <-src(%d) DEBUG cmd = %s cmdstring is %s %s:%d Calling printerConfig binary ... DEBUG DEBUG DEBUG Calling unmount for USB ... DEBUG Calling mount for USB ...
PAGE 29
Unified Services Router cpuMemUsageDBUpdateHandler: SQL error: %s unable to open the DB file %s umiInit failed unable to register to UMI Error Reading from the Database. short DB update event request! User Manual ERROR ERROR ERROR ERROR ERROR ERROR Error in executing DB update handler adpListNodeRemove : Returned with an error command too long. Try increasing " failed to allocate memory for CRON_NODE sqlite3QueryResGet failed There was an error while reading the schedules.
PAGE 30
Unified Services Router User Manual wan traffic counters are restared DEBUG Traffic limit has been reached Traffic meter monthly limit has been changed to %d. Enabling traffic meter for only dowload. Enabling traffic meter for both directions. Enabling traffic meter with no limit. Email alert in traffic meter disabled. Email alert in traffic meter enabled.
PAGE 31
Unified Services Router User Manual Enabling attack check for L2TP. Enabling attack check for UDP Flood. Enabling attack check for IPsec. Enabling attack check for PPTP. DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG Updating BlockSites Keyword from \ Inserting BlockSites Keyword \ Deleting Trusted Domain \ Adding Trusted Domain \ Restarting Schedule Based Firewall Rules Enabling attack check for L2TP.
PAGE 32
Unified Services Router Internet on port %d Enabling remote access management for IP address range" Enabling remote access management to only this PC. Disabling Management Access from Internet on port %d Disabling remote access management for IP address range" Disabling remote access management only to this PC. MAC Filtering %sabled for BLOCK and PERMIT REST. MAC Filtering %sabled for PERMIT and BLOCK REST. Enabling Content Filtering. Disabling Content Filtering.
PAGE 33
Unified Services Router User Manual Update FirewallRules6 where ScheduleName = '%s' to New " DEBUG DEBUG fwLBSpillOverConfigure: Could not set POSTROUTING rules fwLBSpillOverConfigure: Something going wrong Here fwL2TPGenericRules.c: unable to open the database file " fwL2TPGenericRules.c: inet_aton failed fwPPTPGenericRules.c: unable to open the database file " fwPPTPGenericRules.
PAGE 34
Unified Services Router User Manual Facility: Local0 (Wireless) Log Message (node=%s) setting %s to val = %d Custom wireless event: '%s' Wireless event: cmd=0x%x len=%d New Rogue AP (%02x:%02x:%02x:%02x:%02x:%02x) detected WPS session in progress, ignoring enrolle assoc request Severity DEBUG DEBUG DEBUG Log Message sqlite3QueryResGet failed sqlite3QueryResGet failed VAP(%s) set beacon interval failed Severity ERROR ERROR ERROR DEBUG VAP(%s) set DTIM interval failed ERROR DEBUG ERROR ran query %s
PAGE 35
Unified Services Router Got PNAC_EVENT_PREAUTH_SUCCESS event for : %s event for non-existent node %s PNAC_EVENT_EAPOL_START event received PNAC_EVENT_EAPOL_LOGOFF event received PNAC_EVENT_REAUTH event received PNAC_EVENT_AUTH_SUCCESS event received PNAC_EVENT_PORT_STATUS_CHAN GED event received User Manual DEBUG DEBUG unsupported event %d from PNAC event for non-existent node %s. Create new node.
PAGE 36
Unified Services Router User Manual sending EAPOL pdu to PNAC... creating pnac authenticator with values %d %d - %s Profile %s does not exist IAPP initialized.
PAGE 37
Unified Services Router pnacRecvRtn: no corresponding pnac port pae found sending unicast key User Manual DEBUG DEBUG umiIoctl(UMI_COMP_IAPP,%d) failed Invalid IE.
PAGE 38
Unified Services Router from pnacRecvMapi: pkt body len = %d, pktType = %d from pnacPDUProcess: received PNAC_EAP_PACKET User Manual from pnacPDUProcess: currentId = %d from pnacPDUProcess: code = %d, identifier = %d, " from pnacPDUProcess: setting rxResp true from pnacPDUProcess: code = %d, identifier = %d, " DEBUG from pnacPDUProcess: received " DEBUG from pnacPDUProcess: received " from pnacPDUProcess: received PNAC_EAPOL_KEY_PACKET DEBUG doing pnacTxCannedFail DEBUG doing pnacTxCannedSuccess d
PAGE 39
Unified Services Router from pnacBackAuthFail: calling pnacTxCannedFail %s returned ERROR pnacUmiIoctlHandler: cmd: %s(%d) %s not configured for 802.1x could not process PDU received from the wire pnacPDUForward: failed to foward the received PDU Creating PHY port with AUTH backend : %s SendRtn: %p RecvRtn:%p pnacUmiAuthConfig: %s not configured for 802.
PAGE 40
Unified Services Router User Manual phyPort:%s pnacPortPaeDeconfig:kpnacPortPaeDec onfig failed pnacPortPaeDeconfig:kpnacPortPaeDec onfig failed WARN WARN pnacBackAuthSuccess: failed to notify the destination " WARN could not initialize MGMT framework ERROR umiInit failed ERROR iappInit failed ERROR could not initialize IAPP MGMT. ERROR dot11Malloc failed ERROR buffer length not specified Invalid length(%d) specified Failed to get information about authorized AP list.
PAGE 41
Unified Services Router Failed to initiate PBC based enrolle association Invalid association mode.
PAGE 42
Unified Services Router User Manual Invalid Cipher type %d Profile supports WEP stas,Group cipher must be WEP ERROR Profile %s does not exist ERROR Profile %s does not exist ERROR Profile %s does not exist invalid pairwise cipher type %d ERROR ERROR Cipher %s is already in the list. ERROR Profile %s does not exist ERROR Invalid Cipher type %d ERROR Cipher %s not found in the list.
PAGE 43
Unified Services Router User Manual Error in executing DB update handler ERROR sqlite3QueryResGet failed ERROR: incomplete DB update information. old values result does not contain 2 rows ERROR sqlite3QueryResGet failed ERROR Error in executing DB update handler ERROR sqlite3QueryResGet failed.Query:%s ERROR sqlite3QueryResGet failed.Query:%s ERROR sqlite3QueryResGet failed.Query:%s ERROR sqlite3QueryResGet failed.
PAGE 44
Unified Services Router User Manual Invalid config data ERROR Facility: Kernel Log Message DNAT: multiple ranges no longer supported DNAT: Target size %u wrong for %u ranges, Severity Log Message Severity DEBUG %s: %s%s:%d -> %s:%d %s, DEBUG DEBUG DEBUG DNAT: wrong table %s, tablename DNAT: hook mask 0x%x bad, hook_mask %s%d: resetting MPPC/MPPE compressor, DEBUG %s: %s%s:%d %s, %s: Failed to add WDS MAC: %s, dev>name, %s: Device already has WDS mac address attached, %s: Added WDS MAC: %s, dev
PAGE 45
Unified Services Router User Manual %s%d: bad sequence number: %d, expected: %d, DEBUG PPPIOCDETACH file->f_count=%d, PPP: outbound frame not passed PPP: VJ decompression error PPP: inbound frame not passed PPP: reconstructed packet PPP: no memory for missed pkts %u..
PAGE 46
Unified Services Router %s: mac_del %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] %s: mac_kick %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] %s: mac_undefined %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] %s: addr_add %02X:%02X:%02X:%02X:%02X:%02X, dev->name, addr[0], addr[1], addr[2], addr[3], addr[4], addr[5] %s: addr_del %02X:%02X:%02X:%02X:%02X:%02X, dev->nam
PAGE 47
Unified Services Router %s: flow dst=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_dst, family) %s: flow src=%s, __FUNCTION__, XFRMSTRADDR(fl->fl6_src, family) a guy asks for address mask. Who is it? icmp v4 hw csum failure) expire>> %u %d %d %d, expire, expire++ %u %d %d %d, expire, rt_cache @%02x: %u.%u.%u.%u, hash, rt_bind_peer(0) @%p, NET_CALLER(iph) ip_rt_advice: redirect to ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, UDP: short packet: From %u.%u.%u.%u:%u %d/%d to %u.%u.%u.%u:%u, UDP: bad checksum. From %d.%d.
PAGE 48
Unified Services Router ip_rt_bug: %u.%u.%u.%u -> %u.%u.%u.%u, %s, UDP: short packet: From %u.%u.%u.%u:%u %d/%d to %u.%u.%u.%u:%u, UDP: bad checksum. From %d.%d.%d.%d:%d to %d.%d.%d.%d:%d ulen %d, REJECT: ECHOREPLY no longer supported. ipt_rpc: only valid for PRE_ROUTING, FORWARD, POST_ROUTING, LOCAL_IN and/or LOCAL_OUT targets.
PAGE 49
Unified Services Router User Manual %s: failed to register sysctls!, sc>sc_dev->name %s: mac %d.%d phy %d.%d, dev>name, 5 GHz radio %d.%d 2 GHz radio %d.%d, radio %d.%d, ah->ah_analog5GhzRev >> 4, radio %d.
PAGE 50
Unified Services Router User Manual WINDOW=%u , ntohs(th->window) RES=0x%02x , (u8)(ntohl(tcp_flag_word(th) & TCP_RESERVED_BITS) >> 22) URGP=%u , ntohs(th->urg_ptr) DEBUG TRUNCATED DEBUG %02X, op[i] DEBUG PROTO=UDP DEBUG INCOMPLETE [%u bytes] , DEBUG SPT=%u DPT=%u LEN=%u , DEBUG SPT=%u DPT=%u LEN=%u , PROTO=ICMP DEBUG DEBUG INCOMPLETE [%u bytes] , TYPE=%u CODE=%u , ich->type, ich>code DEBUG INCOMPLETE [%u bytes] , DEBUG ID=%u SEQ=%u , DEBUG PARAMETER=%u , DEBUG GATEWAY=%u.%u.%u.
PAGE 51
Unified Services Router User Manual PHYSOUT=%s , physoutdev->name DEBUG MAC= DEBUG %02x%c, *p, DEBUG NAT: no longer support implicit source local NAT NAT: packet src %u.%u.%u.%u -> dst %u.%u.%u.%u, SNAT: multiple ranges no longer supported format,##args) DEBUG DEBUG DEBUG DEBUG version offset_before=%d, offset_after=%d, correction_pos=%u, x->offset_before, x>offset_after, x->correction_pos DEBUG ip_ct_h323: DEBUG DEBUG %s: Error.
PAGE 52
Unified Services Router User Manual >msg_iov[i].iov_base)[j] %02X, skb->data[i] _lvl PPPOL2TP: _fmt, ##args %02X, ptr[length] %02X, ((unsigned char *) m>msg_iov[i].iov_base)[j] %02X, skb->data[i] _lvl PPPOL2TP: _fmt, ##args %02X, ptr[length] %02X, ((unsigned char *) m>msg_iov[i].iov_base)[j] DEBUG DEBUG DEBUG De initializing by \ kernel UMI module loaded kernel UMI module unloaded INFO INFO INFO DEBUG DEBUG DEBUG DEBUG Loading bridge module Unloading bridge module unsupported command %d, cmd Loading
PAGE 53
Unified Services Router User Manual test key, key pre-hashed key, key const char *descr, krb5_keyblock *k) { AES 128-bit key, &key const char *descr, krb5_keyblock *k) { test key, key DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG pre-hashed key, key const char *descr, krb5_keyblock *k) { DEBUG DEBUG 128-bit AES key,&dk DEBUG 256-bit AES key, &dk WARNING: bwMonMultipathNxtHopSelect:: checking rates hop :%d dev:%s usableBwLimit = %d currBwShare = %d lastHopSelected = %d weightedHopPrefer = %d , 1.
PAGE 54
Unified Services Router User Manual Failed to set AES encrypt key AES %s Decrypt Test Duration: %d:%d, hard ? Hard : Soft, DEBUG ICMP: %u.%u.%u.%u: INFO DEBUG INFO Failed to set AES encrypt key DEBUG Failed to set AES encrypt key DEBUG ICMP: %u.%u.%u.%u: Source Wrong address mask %u.%u.%u.%u from Redirect from %u.%u.%u.
PAGE 55
Unified Services Router MD5 Software Test %s, md5SoftTest(0) ? Failed : Passed User Manual DEBUG %s: options rejected: o[0]=%02x, o[1]=%02x, MD5 Hardware Test: MD5 Hardware Test %s, md5HardTest(0) ? Failed : Passed DEBUG DEBUG %s: don't know what to do: o[5]=%02x, *** New port %d ***, ntohs(expinfo>natport) AES Software Test: %d iterations, iter DEBUG ** skb len %d, dlen %d,(*pskb)->len, AES Software Test Duration: %d:%d, DEBUG ********** Non linear skb AES Hardware Test: %d iterations, iter D
PAGE 56
Unified Services Router Value = %x ::: At Page = %x : Addr = %x REG Size == 32 Bit Value = %x ::: At Page = %x : Addr = %x User Manual DEBUG WARNIN G WARNIN G WARNIN G WARNIN G WARNIN G WARNIN G WARNIN G DEBUG %s: no rates for %s?, no rates yet! mode %u, sc>sc_curmode DEBUG %u.%u.%u.%u sent an invalid ICMP REG Size is not in 8/16/32/64 Written Value = %x ::: At Page = %x : Addr = %x DEBUG dst cache overflow DEBUG Neighbour table overflow. bcm_ioctl :Unknown Ioctl Case : DEBUG host %u.%u.%u.
PAGE 57
Unified Services Router User Manual from G WARNIN G WARNIN G ERROR %s(): ADDBA mode is AUTO, __func__ DEBUG martian source %u.%u.%u.
PAGE 58
Unified Services Router User Manual [%d]\tMacAddr\t%s, j, [%d]\tDescp\t\t%s, j, ni>node_trace[i].descp [%d]\tValue\t\t%llu(0x%llx), j, ni>node_trace[i].
PAGE 59
Unified Services Router __FUNCTION__ %s: failed to register sysctls!, proc_name PKTLOG_TAG %s: proc_mkdir failed, __FUNCTION__ PKTLOG_TAG %s: pktlog_attach failed for %s, PKTLOG_TAG %s:allocation failed for pl_info, __FUNCTION__ PKTLOG_TAG %s:allocation failed for pl_info, __FUNCTION__ PKTLOG_TAG %s: create_proc_entry failed for %s, PKTLOG_TAG %s: sysctl register failed for %s, PKTLOG_TAG %s: page fault out of range, __FUNCTION__ PKTLOG_TAG %s: page fault out of range, __FUNCTION__ PKTLOG_TAG %s: Log buffer
PAGE 60
Unified Services Router %s: cancel DFS WAIT period on channel %d, __func__, sc>sc_curchan.channel Non-DFS channel, cancelling previous DFS wait timer channel %d, sc>sc_curchan.
PAGE 61
Unified Services Router User Manual ,__func__ int)len %s: unable to start recv logic, %s: Invalid interface id = %u, __func__, if_id %s: unable to allocate channel table, __func__ %s: Tx Antenna Switch. Do internal reset.
PAGE 62
Unified Services Router User Manual >ifName Wakingup due to wow signal %s, wowStatus = 0x%x, __func__, wowStatus DEBUG Pattern added already Error : All the %d pattern are in use.
PAGE 63
Unified Services Router User Manual 0x%08x 0x%08x, 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG sc_txq[%d] : , i DEBUG tid %p pause %d : , tid, tid->paused %d: %p , j, tid->tx_buf[j] DEBUG DEBUG %p , buf axq_q: %s: unable to reset hardware; hal status %u, __func__, status DEBUG DEBUG ****ASSERTION HIT**** MacAddr=%s, DEBUG DEBUG TxBufIdx=%d, i DEBUG Tid=%d, tidno AthBuf=%p, tid->tx_buf[i] %s: unable to reset hardware; hal status %u, %s: unable to reset hardware; hal status %u, DEBUG DEBUG %s: unable t
PAGE 64
Unified Services Router Index:%d, value:%d, code:%x, rate:%d, flag:%x, i, (int)validRateIndex[i], RateTable:%d, maxvalidrate:%d, ratemax:%d, pRc->rateTableSize,k,pRc>rateMaxPhy User Manual DEBUG DEBUG Can't allocate memory for ath_vap. DEBUG Unable to add an interface for ath_dev.
PAGE 65
Unified Services Router User Manual Appendix E.
PAGE 66
Unified Services Router User Manual Appendix F. Product Statement 1. DSR-1000N Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 67
Unified Services Router User Manual IMPORTANT NOTE: Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with IC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter is restricted to indoor use in the 5150MHz to 5250MHz frequency range.
PAGE 68
Unified Services Router User Manual Česky [Czech] [D-Link Corporation] tímto prohlašuje, že tento [DSR-1000N] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [D-Link Corporation] erklærer herved, at følgende udstyr [DSR-1000N] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
PAGE 69
Unified Services Router Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] User Manual [D-Link Corporation] declara que este [DSR-1000N]está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. [D-Link Corporation] izjavlja, da je ta [DSR-1000N] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. [D-Link Corporation] týmto vyhlasuje, že [DSR-1000N] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
PAGE 70
Unified Services Router User Manual 2.DSR-500N Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 71
Unified Services Router User Manual Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2006+A11:2009 Safety of information technology equipment - EN 300 328 V1.7.
PAGE 72
Unified Services Router User Manual Česky [Czech] [D-Link Corporation] tímto prohlašuje, že tento [DSR-500N] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [D-Link Corporation] erklærer herved, at følgende udstyr [DSR-500N] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
PAGE 73
Unified Services Router Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] User Manual [D-Link Corporation] declara que este [DSR-500N]está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. [D-Link Corporation] izjavlja, da je ta [DSR-500N] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. [D-Link Corporation] týmto vyhlasuje, že [DSR-500N] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
PAGE 74
Unified Services Router User Manual 3.DSR-250N Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 75
Unified Services Router User Manual Is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC), the procedures given in European Council Directive 99/5/EC and 2004/104/EC. The equipment was passed. The test was performed according to the following European standards: EN 300 328 V.1.7.1 EN 301 489-1 V.1. 8.1 / EN 301 489-17 V.2.1.