Version 1.
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date 1.0 October 15, 2013 Description • Initial release Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface.................................................................................. i Manual Revisions............................................................................ i Trademarks....................................................................................... i Product Overview............................................................... 1 Package Contents..........................................................................
Table of Contents Wi-Fi..................................................................................................44 Basic..........................................................................................44 Wireless Security..................................................................46 Wired Equivalent Privacy (WEP)................................46 Wi-Fi Protected Access (WPA).....................................47 WLAN Authentication and Privacy Infrastructure (WAPI).................
Section 1 - Product Overview Product Overview Package Contents D-Link DWR-730 HSPA+ Mobile Router Battery USB Cable Power Adapter If any of the above items are missing from your package, please contact your reseller. System Requirements • A compatible (U)SIM card with mobile data service1 • A computer a with Windows®, Macintosh® , or Linux-based operating systems • Internet Explorer 8, Firefox 12.0, Chrome 20.0 , or Safari 4.0 1 Subject to services and service terms available from your carrier.
Section 1 - Product Overview Introduction The D-Link DWR-730 HSPA+ Mobile Router lets you share a fast mobile Internet connection with multiple PCs and mobile devices wherever you go. It offers 3G HSPA+ compatibility for fast downlink and uplink data rates, so you get the high-speed upload and download speeds even when you’re on the go. Set up a personal mobile network anywhere, anytime allowing you and those around you to access the Internet, and share files.
Section 1 - Product Overview Hardware Overview Left Side Power Button WPS Button microSD Card Slot microUSB Port Power Button WPS Button microSD Card Slot micro USB Connector D-Link DWR-730 User Manual Press and hold this button for 6 seconds to power on/off the device. Press this button to add new wireless devices quickly and easily using Wi-Fi Protected Setup (WPS). Press and hold for more than 5 seconds to turn the wireless function on/off.
Section 1 - Product Overview Hardware Overview OLED Display The current status of the DWR-730’s functions including mobile network, Wi-Fi, security, Internet status, signal strength, and battery level will be shown on the OLED display. Please refer to the table below for the specific indications which are shown on the display.
Section 1 - Product Overview 3 4 5 6 7 8 9 10 Wi-Fi & Clients Internet Connection Status SMS Number Internet Indicates that the Wi-Fi network is currently tuned on Indicates the number of clients currently connected to the device by Wi-Fi If this icon is displayed, there is an Internet connection present There are unread SMS messages in the inbox Displays the current battery level.
Section 2 - Installation Installation This section will guide you through the installation process. Connect to Your Network 1. Ensure that your DWR-730 HSPA+ Mobile Router is powered off. 2. Remove the back cover and take out the battery. Slide your (U)SIM card into the slot provided, ensuring that the alignment is the same as indicated by the logo next to the slot. The gold contacts on the card should be facing downwards.
Section 2 - Installation Driver Installation When you plug the DWR-730 into your computer, any necessary drivers will immediately install (with your permission). Note: These drivers are Windows-only. Mac and Linux users will still be able to configure the DWR-730 using the web configuration utility described in “Configuration Utility” on page 12.
Section 2 - Installation Wireless Installation Considerations The DWR-730 can be accessed using a wireless connection from anywhere within the operating range of its wireless network. Keep in mind that the quantity, thickness, and location of walls, ceilings, or other objects that the wireless signals must pass through may adversely affect wireless signals. Ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or office.
Section 2 - Installation Configuration This section will show you how to configure your new D-Link mobile router using the configuration utility that can be obtained through a software interface or a web-based user interface. Initial Connection to the Router When configuring the router for the first time, you will need to establish a direct connection with the router in order to access the web-based configuration utility.
Section 2 - Installation Connect via Wi-Fi Note: The following example uses Windows 7’s built-in wireless connection utility. If you are using a different operating system, or a third party connection utility, the process may be different. Please refer to the documentation that came with your operating system or wireless client for further information on how to connect to a wireless network.
Section 2 - Installation You will then be prompted to enter the network security key for your router. The unique security key for your router will be displayed on a sticker in the router’s battery bay. Enter the security key in the box provided and click OK. Your wireless connection utility should confirm that the connection is successful, and you can move to the next step to continue to configuration process.
Section 3 - Configuration Web-based Configuration To access the configuration utility, open a web browser (such as Internet Explorer) and enter the IP address of the router, which is 192.168.0.1 by default. Configuration Utility Once you have reached the configuration utility through the installed software or your web browser, you will need to log in. Enter admin as the username, and then enter the password. By default, the password is blank. You can also select your language from the drop-down menu.
Section 3 - Configuration Home Navigation Throughout the interface you will find a menu bar at the top of the page which includes tabs for easy navigation, and a summary bar in the upper right corner with a quick view of essential information. Home The Home tab will return you the home page, where a summary of the system information is shown. Wizard: Click on this tab to start the setup wizard, which will guide you through the basic setup process.
Section 3 - Configuration Device Status A summary of the device’s current status will be displayed on the information panel at the top of the right-hand side of the navigation bar. The following is a description of the indications, from left to right. SIM: This icon shows whether or not a compatible (U)SIM card has been inserted into the device. SMS: The number to the right of this icon indicates the number of unread messages in the SMS inbox.
Section 3 - Configuration Home The Home page acts as a dashboard to quickly display your configuration settings and provide a summary of the current status of your network’s status. System Resources: This area displays the percentage of the router’s memory and CPU currently being used by the system. LAN: This area displays a summary of the current settings for the router’s LAN. 2G/3G Modem: This area shows the current status of your 2G or 3G mobile network connection.
Section 3 - Configuration Wizard The Wizard page will guide you through the steps required to configure the basic settings of your router such as the IP address, network name (SSID), and password. Click on the Wizard button on the navigation bar to commence the wizard. LAN Configuration IP Address: If you wish to change the router’s IP address, enter the new address here.
Section 3 - Configuration Wi-Fi Configuration Password Setting: Choose a password for your wireless security. Clients will need this password in order to access your network wirelessly. If you are currently connected to the router using Wi-Fi, you will need to reconnect to the router using your new password once the wizard has been completed. SSID: If you wish to change your wireless network name (SSID), enter a new name in the field provided.
Section 3 - Configuration Internet Connection This page allows you to configure the Internet settings for your mobile network connection. Use the tabs in the left-hand column to navigate through the different settings categories. Connection Operation Flight Mode: Flight mode turns off all communications so that the device can be powered on safely when in an aircraft. Select whether you want to Enable or Disable flight mode from the dropdown menu, and click Change to effect the change.
Section 3 - Configuration Connection: Shows the type and status of the current mobile connection. To change the connection profile, select a user profile from the table below and click Set to activate the profile. Click Disconnect to manually disconnect the current mobile data service. Profiles: The profiles table shows the details of currently configured user profiles. To add a new user profile, navigate to the User Profile tab at the top of this section. User Profile Click Add to add a new user profile.
Section 3 - Configuration Configuration This section allows you to specify the settings for your Internet connection depending on the type of connection you wish to use, or as specified by your Internet Service Provider. Use the IPv4 and IPv6 tabs at the top of the section to select the IP address mode. IPv4 - PDP Context Connection Select PDP Context from the drop-down menu. Type: DNS Setting: Enter up to three DNS servers as provided to you by your service provider. Click Apply to apply the changes.
Section 3 - Configuration IPv4 - Static Setting Use this setting if your Internet Service Provider has supplied you with a static (non-changing) IPv4 address. If you are missing any of the information required in this section, please contact your ISP. Connection Select Static Setting from the drop-down menu. Type: IP Address: Enter the static IP address provided to you by your ISP. Mask: Enter the subnet mask provided to you by your ISP. Gateway: Enter the default gateway provided to you by your ISP.
Section 3 - Configuration IPv4 - 4to6 Use this setting if you wish to use IPv4 through an IPv6 tunnel. Connection Select 4to6 from the drop-down menu. Type: Remote IPv6 Enter the remote IPv6 address for your connection. Address: Remote IPv4 Enter the remote IPv4 address for your connection. Address: Local IPv6 Select User Define from the drop-down menu to define your Address: own local IPv6 address, or select WAN IPv6 Address to use the remote IPv6 address.
Section 3 - Configuration IPv6 - PDP Context Connection Select PDP Context from the drop-down menu. Type: DNS Setting: Enter up to three DNS servers as provided to you by your ISP. Click Apply to apply the changes.
Section 3 - Configuration IPv6 - Static Setting Use this setting if your Internet Service Provider has supplied you with a static (non-changing) IPv6 address. If you are missing any of the information required in this section, please contact your ISP. Connection Select Static Setting from the drop-down menu. Type: Static IP Enter the static IPv6 address that has been supplied to you by your service provider. Gateway: Enter the IPv6 gateway that has been supplied to you by your service provider.
Section 3 - Configuration IPv6 - DHCPv6 Use this setting if your Internet connection settings and IP address are to be obtained automatically from your ISP. Connection Select DHCPv6 from the drop-down menu. Type: DNS Setting: Enter up to three DNS servers as provided to you by your service provider. Click Apply to apply the changes.
Section 3 - Configuration IPv6 - Tethering Use this option to tether an IPv6 connection. Connection Select Tethering from the drop-down menu. Type: DNS Setting: Enter up to three DNS servers as provided to you by your service provider. Click Apply to apply the changes.
Section 3 - Configuration IPv6 - 6to4 Use this setting if you wish to use IPv6 through an IPv4 tunnel. Connection Select 6to4 from the drop-down menu. Type: 6to4 Relay: Enter the address of the 6to4 relay server to be used for this connection. DNS Setting: Enter up to three DNS servers as provided to you by your ISP. Click Apply to apply the changes.
Section 3 - Configuration IPv6 - 6rd Use this setting if you wish to use the IPv6 Rapid Deployment (RD) protocol. Connection Select 6rd from the drop-down menu. Type: 6rd Select Manual from the drop-down menu to manually enter Configuration: your 6rd connection information. Select DHCP 6rd Option to receive connection information automatically from your service provider. 6rd Prefix: Enter the 6rd prefix supplied by your service provider.
Section 3 - Configuration 2G/3G Modem This section displays information about your 2G or 3G modem connection. Information Information: Displays information about your 2G or 3G modem. Settings Network: Select your preferred modem type from the drop-down menu: Auto - The modem will automatically select the modem type depending on the network it is connected to. 3G Only - The modem will only connect to 3G networks. 2G Only - The modem will only connect to 2G networks.
Section 3 - Configuration SIM This section allows you to turn SIM lock on or off for the SIM card which is currently inserted into the router. PIN Code: Enter the PIN code for the SIM card. Click Enable to turn on SIM lock, or click Disable to turn off SIM lock.
Section 3 - Configuration PLMN This page allows you to view available Public Land Mobile Networks (PLMN). This page can also be used to select a preferred network when you are roaming outside of your home network. Mode: Select Automatic to allow the router to automatically connect to the first available network when roaming. Select Manual to choose your preferred roaming network from the list below.
Section 3 - Configuration Network The Network pages allow you to check the current status of your Local Area Network (LAN), and make changes to LAN settings.
Section 3 - Configuration Wi-Fi This section allows you to configure the IP settings for your wireless network. IPv4 IP Address: Enter the IPv4 address for your Wi-Fi network. If you change this address, you will need to enter the new address in your web browser’s address bar in order to access the web-based configuration utility. IP Subnet Mask: Enter the IPv4 subnet mask for your Wi-Fi network. Click Apply to save the current configuration.
Section 3 - Configuration DHCP The DWR-730 has a built-in DHCP server which can assign IP addresses to connected clients. This section allows you to configure the DHCP settings. DHCP Server DHCP Mode: Select the desired DHCP mode from the drop down menu: None - Turns off DHCP functionality Server - The router will act as a DHCP server and assign IP addresses to connected devices. Relay - The router will act as a relay between DHCP clients and a DHCP server on another subnet.
Section 3 - Configuration NTP Server First/Second/ Select None from the drop-down menus if you do not wish Third NTP to specify a first, second, or third Network Time Protocol Server: server. Select From ISP to use the automatic settings supplied by your ISP, or select User Define to specify an NTP server, and enter the address of the server in the field provided. Click Apply to save the current configuration.
Section 3 - Configuration DHCPv6 This section allows you to configure your router’s DHCP server for the IPv6 protocol. To edit any of the fields under this tab, click on the field that you wish to edit, and a text box will appear. Click OK at the bottom of each section to save that particular rule or configuration. Options DUID-LLT: Displays the router’s DHCP Unique Identifier. Enable: Check the box to enable the router to operate as a DHCPv6 server and issue DHCPv6 IP addresses to requesting clients.
Section 3 - Configuration SIP Server: Select Y(es) or N(o) as the status of the SIP server function. Enter the address of a Session Information Protocol (SIP) server. SIP Domain: Select Y(es) or N(o) as the status of the SIP domain name function. Enter the SIP domain name for the rule. NIS Server: Select Y(es) or N(o) as the status of the NIS server function. Enter the address of a Network Information Service (NIS) server. NIS Domain: Select Y(es) or N(o) as the status of the NIS domain name function.
Section 3 - Configuration Address Pool This tab allows you to specify address ranges for the DHCPv6 address pool. These addresses will be assigned to DHCPv6 clients that request an IPv6 address from the DHCP server. Active: Check the box to activate the address pool rule. Start Address: Enter the starting IPv6 address for the pool range. End Address: Enter the ending IPv6 address for the pool range. Preferred Enter the preferred lifetime for addresses in the DHCP pool.
Section 3 - Configuration Client Assigned Address Active: Check the box to activate the rule. Client #: Enter a number to identify the client. Address: Enter the address to be assigned. Preferred Enter the preferred lifetime for the address to be assigned. Lifetime: Valid Lifetime: Enter the valid lifetime for the address to be assigned. Click OK to save the current rule. Client Delegated Prefix Active: Check the box to activate the rule. Client #: Enter a number to identify the client.
Section 3 - Configuration NAT This section allows you to configure functions related to Network Address Translation (NAT) such as port triggering. Port Trigger Use this option to have inbound traffic automatically forwarded to a dynamic address on the LAN when triggered by outbound traffic. To add a new port triggering rule, click Add. Active: Check the box to activate this rule. Name: Specify a name to identify the rule.
Section 3 - Configuration ALG Application Level Gateways (ALG) allow certain applications to augment a network’s firewall or NAT. This section enables you to enable various ALGs as required by specific applications. To enable an ALG, check the box next to the name of the rule. SIP Port: Enter the Session Initiation Protocol (SIP) port required by your applications. Click Apply to save the settings and return to the Network page.
Section 3 - Configuration NAT 64 NAT 64 allows you to configure Network Address Translation for the IPv6 protocol. Enable: Check the box to enable the NAT64 function. Virtual IPv4 Enter the IPv4 address to be used for the virtual IPv4 address Pool: pool. NAT64 Prefix: Enter the IPv6 prefix you wish to add, and select a prefix length from the drop-down menu. Click OK to save the rule. Click OK to save the current configuration.
Section 3 - Configuration SMS The DWR-730 can send and receive SMS text messages through the mobile network’s SMS function. In this section you can check the SIM card’s inbox and outbox, as well as send new messages. New Message Send To: Enter the phone number that you wish to send the message to Messages: Enter the body of the message to be sent. Click Apply to save the current configuration. Local Inbox This tab shows a summary of SMS messages in the inbox.
Section 3 - Configuration Wi-Fi The Wi-Fi pages allow you to check the current status of your Wi-Fi network, and make changes to Wi-Fi settings. Basic This section allows you to configure your Wi-Fi network and specify the wireless security method to be used to secure your network. Enable Check the box to enable the Wi-Fi function. Mode: Select the desired 802.11 wireless mode from the dropdown menu.
Section 3 - Configuration DTIM Period: The Delivery Traffic Indication Message broadcasts information about buffered data to clients that are currently in low-power mode. Enter the desired DTIM period as a number of beacon intervals. SSID: Enter the SSID (network name) to identify your wireless network. Hide SSID: Check the box to hide the SSID of your network. If the SSID is hidden, wireless clients must manually enter it in order to connect to your network.
Section 3 - Configuration Wireless Security It is recommended that you enable wireless security on your router in order to protect your wireless network from unauthorized access. You should select a wireless security protocol that is compatible with the wireless clients which will be accessing your network.
Section 3 - Configuration Wi-Fi Protected Access (WPA) Wi-Fi Protected Access (WPA) is a newer and more secure encryption protocol which makes significant improvements over WEP. There are two versions of WPA; the original WPA, and the newer WPA2. Encryption Type: Select WPA Personal from the drop-down menu.
Section 3 - Configuration WLAN Authentication and Privacy Infrastructure (WAPI) WLAN Authentication and Privacy Infrastructure (WAPI) is a wireless security standard which is implemented in China. You should only use this protocol if your wireless clients do not support any of the other security methods provided by the DWR-730. Encryption Type: Select WAPI Personal from the drop-down menu. WAPI Pre-Shared Select whether your key should use ASCII or HEX characters Key: using the drop down menu.
Section 3 - Configuration Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) enables you to quickly and securely add compatible devices to your wireless network. Enable: Check the box to enable the Wi-Fi Protected Setup feature. Configure State: Select whether you wish to Configure or Unconfigure the WPS function using the radio buttons. Configure Method: Select the WPS method that you wish to use.
Section 3 - Configuration MAC Filter The MAC filtering option allows you to allow or deny access to wireless clients based on their MAC address. Enable MAC Address Check the box to enable the MAC filtering feature. Filter: Mode: Select the filtering mode from the drop-down menu. You can choose to Deny Listed Stations access to your network, or Allow Listed Stations access. Listed Stations Table To add a new filtering rule, click Add. Active: Check the box to activate the rule.
Section 3 - Configuration Station Lists The Station List tab shows a list of all wireless clients currently connected to your wireless network.
Section 3 - Configuration Advanced IPv4 The IPv4 routing table lists all current routing rules. Click Add to add a new routing rule. Destination IP: Enter the destination IP address for your route. Destination Mask: Enter the destination mask for your route. Next Hop Type: Select Interface or IP Address as the hop type from the drop-down menu. Next Hop Interface: Select either LAN or WAN as the next hop interface from the drop-down menu. Metric: The metric will determine your route selection process.
Section 3 - Configuration IPv6 The IPv6 routing table lists all current routing rules. Click Add to add a new routing rule. Active: Check the box to activate the rule. Destination Prefix: Enter the destination IPv6 address prefix for your route. Route Type: Select Directly Attached, Recursive, or Fully Specified from the drop-down menu. Output Interface: Select either LAN or WAN as the next hop interface from the drop-down menu. Next Hop Address: Enter the next hop IPv6 address.
Section 3 - Configuration RIP The Routing Information Protocol (RIP) uses metrics to prevent routing loops from being propagated. Use this section to configure your router’s RIP settings. Setting Enable: Check the box to enable RIP. The table will show details of your RIP settings. LAN Direction: Select the desired direction in which to apply RIP. Select RX/ TX to apply RIP in both inbound and outbound directions, RX for inbound only, and TX for outbound only.
Section 3 - Configuration LAN IPv6 RA This tab allows to you customize what information is sent in the router’s advertisement packets. IsRouter: Select the router advertisement flag status. AdvSend Check this box to have the router send advertisements. Advertisements: Unicast Only: Check the box to have the router advertise unicast addresses only. MaxRtrAdvInterval: Enter the maximum advertisement interval. MinRtrAdvInterval: Enter the minimum advertisement interval.
Section 3 - Configuration AdvDefaultLifetime: Enter the default lifetime of router advertisements. AdvDefault From the drop-down menu, select the default preferability of Preference: the address as a default router address. AdvSource Check the box to allow the advertisement of the source linkLLAddress: local address. Click Apply to save the current configuration. Prefix Use this tab to customize the prefixes for router advertisements. Click Add to add a new prefix. On-Link: Check to specify an on-link flag.
Section 3 - Configuration DNS Configuration Use this tab to specify how the router delivers DNS information using router advertisements. DNSSL: Enter the domain name of the DNS search list to be included in the advertisement. Domain Name of DNS Enter the advertisement lifetime for the domain name. Search List: Click the Delete icon to delete the DNS rule. Click OK to save the current rule. Click Apply to save the current configuration.
Section 3 - Configuration IPv6 Multicast This section allows you to configure your router to receive multicast streams over the IPv6 protocol. Enable: Check the box to enable the router to receive IPv6 multicast streams. Source Enter the source preference in the field provided. Preference: Source Metric: Enter the source metric to be used in the field provided. Candidate RP: Check the box to allow this router to be a candidate rendezvous point (RP).
Section 3 - Configuration Security The Security tab allows you to configure your router’s firewall settings and enable features to protect your network from outside intrusions and malicious attacks. Firewall IP Filter Click Add to add a new filtering rule. Active: Check the box to activate the IP filter rule. Source IP: Enter the source IP address to be filtered. Source From Enter the starting port on the source IP. Port: Source To Port: Enter the ending port on the source IP.
Section 3 - Configuration IPv6 Filter Click Add to add a new filtering rule. Active: Check the box to active the IP filter rule. Source IP: Enter the source IP address to be filtered. Source Port: Enter the port for the source IP. Destination IP: Enter the destination IP address to be filtered. Destination Port: Enter the port on the destination IP. Protocol: Select the protocol for the IP filter rule. Delete: Click the icon to delete the IP filtering rule. Click OK to save the current filtering rule.
Section 3 - Configuration MAC Filter The MAC filter lets you to allow or deny access to your wireless network based on a client’s MAC address. Click Add to add a new MAC filtering rule. Blacklist/ Select Blacklist to deny access to only the MAC addresses Whitelist: listed below. Select Whitelist to allow access to only the MAC addresses listed below. Active: Check the box to activate the MAC filter rule.
Section 3 - Configuration DDOS This section allows you to enable various security features to protect against Denial of Service (DoS) attacks. DoS Prevention Check the box next to the rule to enable prevention against Filters: that specific kind of DoS attack. Click Apply to save the current configuration.
Section 3 - Configuration URL Filter The content filter allows you to allow or deny access to specific URLs. Enable URL Filter: Check the box to enable URL filtering. Blacklist/ Select Blacklist to deny access to only URLs listed in the rule Whitelist: table. Select Whitelist to allow access to only URLs listed in the rule list. Active: Check the box to activate the URL filtering rule. URL: Enter the URL that you wish to allow or deny access to.
Section 3 - Configuration Application This tab allows you to configure the router’s administrative functions, such as time & date, remote access, and firmware. You can also access the system log. About This tab shows the router’s basic information.
Section 3 - Configuration Configuration Backup Click Backup to save the router’s current configuration to a file on your computer. You will then be prompted with a “save file” dialogue, where you can choose where to save the configuration file. Restore Click Browse to locate a previously saved configuration file on your computer. Once you have located the file, click Restore to configure the router according to the selected configuration file.
Section 3 - Configuration Firmware Upgrade You can upgrade the firmware of the router here. Make sure the firmware file you want to use is on the local hard drive of the computer. Please check your local D-Link support site or http://support.dlink.com for firmware updates and language packs. Click Browse to locate a previously downloaded firmware file on your computer. Once the file has been located, click Update to carry out the firmware upgrade process.
Section 3 - Configuration Standby Mode This section allows you to configure the router’s automatic power-saving modes. Enable Auto Check the box to enable the automatic power saving Power Saving: features. Enter Standby Enter the number of minutes after which the router will enter Mode: standby mode if no activity is detected. Enter Hibernate Enter the number of minutes after which the router will enter Mode: hibernate mode if no activity is detected.
Section 3 - Configuration Password This page lets you change the configuration interface passwords for the Administrator (Admin) and User accounts. Select the user Select whether you wish to change the password for the to change admin or user account from the drop down menu. password: Old Password: Enter the existing password for this account. New Password: Enter the new password for this account. Retype New Type the new password again to confirm. Password: Click Apply to save the current configuration.
Section 3 - Configuration Date and Time This page lets you set the time and date for your router, and also configure automatic time synchronization and daylight savings time. Date Current System Displays the current time and date according to the router’s Time: system clock. Mode: Select Manual to manually set the time and date, or select Get from Time Server to have the router automatically synchronize the time with a Network Time Protocol (NTP) server.
Section 3 - Configuration Time Zone Time Zone: Select your time zone from the drop-down menu. Enable Daylight Check the box to enable automatic adjustment for daylight Saving: saving. Start Date: Enter the details of the starting date and time for daylight saving time in your region. End Date: Enter the details of the ending date and time for daylight saving time in your region. Click Apply to save the current settings.
Section 3 - Configuration Language Language: Select your preferred language from the drop-down menu. Click Apply to save the current configuration.
Section 3 - Configuration System Log The system log displays a record of all events which occur while the router is running. Log Setting Enable Log: Check the box to enable the router’s log-keeping function. Click Apply to save the current configuration. Log Display Refresh: Click to update the log display. Clear Log: Click to clear all log entries. Display Log Select the level of log event which you wish to view from the Level: drop-down menu.
Section 4 - Connecting to a Wireless Network Connecting to a Wireless Network Using Windows 8 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key (Wi-Fi password) being used. To join an existing network, locate the wireless network icon in the taskbar, next to the time display.
Section 4 - Connecting to a Wireless Network You will then be prompted to enter the network security key (Wi-Fi password) for the wireless network. Enter the password into the box and click Next. If you wish to use Wi-Fi Protected Setup (WPS) to connect to the router, you can also press the WPS button on your router at this point to enable the WPS function.
Section 4 - Connecting to a Wireless Network Connecting to a Wireless Network Using Windows 7 Windows 7 users may use the built-in wireless utility to connect to a wireless network. If you are using another company’s utility or Windows 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows 7 utility as seen below.
Section 4 - Connecting to a Wireless Network Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to “Networking Basics” on page 90 for more information.
Section 4 - Connecting to a Wireless Network Configuring Wireless Security It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless 2. The utility will display any available wireless networks in your area.
Section 4 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. 4. The following window appears while your computer tries to connect to the router.
Section 4 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 4 - Connecting to a Wireless Network Using Windows Vista™ Windows® Vista™ users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® Vista™ utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.
Section 4 - Connecting to a Wireless Network Configuring Wireless Security It is recommended to enable wireless security (WEP/WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows® Vista™ Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2.
Section 4 - Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 4 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 4 - Connecting to a Wireless Network Configure WEP It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 4 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the same WEP key that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WEP settings are correct. The WEP key must be exactly the same as on the wireless router.
Section 4 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 4 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
Section 5 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DWR-730. Read the following descriptions if you are having problems. 1. Why can’t I access the web-based configuration utility? When entering the IP address of your router (192.168.0.1 for example), you are not connecting to a website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself.
Section 5 - Troubleshooting • Configure your Internet settings: -- Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the Default Level button to restore the settings to their defaults. -- Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. -- Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows® Vista™ users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 8 Click on Start > Control Panel > Network and Internet Connections > Network Connections > Configure your Internet Protocol (IP) settings. Windows® 7 Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.
Appendix C - Technical Specifications Technical Specifications Radio Frequency Bands Wireless Security Cellular Access Firewall • HSUPA/HSPDA/UMTS: 900/2100 MHz or 850/1900 MHz (option) • EDGE/GPRS/GSM: 850/900/1800/1900 MHz • Power Class 3 (+23 dBm) • HSPA+ • Downlink: 21 Mbps • Uplink: 5.76 Mbps Wi-Fi Access Point • 802.11n (150 Mbps compatible) • 802.11g (54 Mbps) • 802.
Appendix D - Safety Warnings and Declarations Specific Absorption Rate (SAR) This mobile device is a radio transmitter and receiver. It is not designed to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health.
CE Warning 1. CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 2. The product shall only be connected to a USB interface of version USB2.0 3. The adapter shall be installed near the equipment and shall be easily accessible. Only can use adapter as below: Adapter brand name: AMIGO Adapter model: AMS47-0501000FV I/P:100-240V,50/60Hz,0.2A,O/P 5V,1.0A The plug considered as disconnect device of adapter 4.
FCC Warning FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
FCC Warning RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
