AUTO FOCUS, DAY&NIGHT ZOOM COLOR CAMERA USER MANUAL 사용 설명서 27X / 33X / 37X 용 서
Contents 1. 2. 3. 4. 5. 6. 7. 8.
1. Precautions Cautions This information is provided to ensure your safety and to prevent any loss, financial, Please read it carefully and use the products accordingly. - Warning Installation of this product by unqualified personnel is strictly prohibited, Please consult an experienced installer or authorized retailer for proper installation to avoid possible fire or electric shock. If the camera overheats or smoke is noticed, turn off immediately.
2. Features High Magnification Zoom Lens High 432 x zoom function. (x27 Optical zoom, x16 Digital zoom) High 528 x zoom function. (x33 Optical zoom, x16 Digital zoom) High 592 x zoom function. (x37 Optical zoom, x16 Digital zoom) High resolution 600TVL Color : more than 600TVL, B/W : more than 700 TVL. SSNR3 Function Low illumination noise has been significantly reduced and resulting in a clear and sharp image display in the dark.
3. Products 구성물 Components 1. Color zoom camera 2.
4. Name and Functions of Each Part 1) Front ①Tripod Mounting Bracket Screw Hole Used to fix tripod mounting bracket on top of the camera. Tripod mounting is attached on bottom of the camera but it can install the mounting in the top of camera when the user need.
2) BACK ① Key Buttons ▪ UP (TELE button): To move the arrow indicator to up - To close in on a far object. (ZOOM IN) ▪ DOWN (WIDE button): To move the arrow indicator to down - To widen the view. (ZOOM OUT) ▪ SET: To access the main setup menu.
☞ Notes • If the Adaptor Power Line is extended improperly, it may cause malfunctions since the camera is affected by unstable voltage condition. • Ensure Power Supply Source: DC 12V ± 10%, 500㎃ • The wire is polarized. Match “+” and “-“terminals properly ③ Video Output Jack - Used to connect an external video monitor in jack. ④ External Control Connector - Zoom and focus functions can be controlled by using external signal, RS-485 communication. ⑤ Power LED - Illuminates when power is supplied.
5. Connection 1) Connecting to Monitor Connect Video Out Jack to the monitor's Video In jack as shown below. • Connect cables with the unit powered down.
Focus and Zoom functions can be controlled by using external signals. * It can be broken by using Overvoltage.
6. Operating Your Camera 1) Menu Configuration MAIN SETUP MENU SSNR ▪ OFF ▪ ON WHITE BALANCE ▪ ATW ▪ OUTDOOR ▪ MANUAL ▪ INDOOR ▪ AWC → SET BACKLIGHT ▪ OFF ▪ BLC ▪ HLC MOTION DET ▪ OFF ▪ ON FOCUS ▪ MODE ▪ ZOOM TRK ▪ ZOOM SPEED ▪ D-ZOOM ▪ ZOOM POS INIT ▪ USER PRESET ▪ LENS INIT ▪ RET EXPOSURE ▪ BRIGHTNESS ▪ SSNR3 SPECIAL ▪ PRIVACY ▪ DAY / NIGHT ▪ DIS ▪ SYNC ▪ COMM ADJ ▪ IMAGE ADJ ▪ MONITOR ▪ DISPLAY ▪ RET ▪ IRIS ▪ SENS-UP RESET EXIT 2) Menu Setup Use the six buttons on back of the camera.
1. Press the SET button for 2 seconds to access the main setup mode. • Main setup menu is displayed on the monitor screen. MAIN SETUP SSDR ON ↙ WHITE BAL ATW BACKLIGHT OFF MOTION DET OFF FOCUS ↙ EXPOSURE ↙ SPECIAL ↙ RESET EXIT 2. Select the desired feature by using the UP or DOWN button. MAIN SETUP Select feature by using The UP button. or DOWN SSDR ON ↙ WHITE BAL ATW BACKLIGHT OFF MOTION DET OFF Change the status by using the LEFT or RIGHT button.
SSDR(Super Dynamic Range) SSDR illuminates darker spots of an image while retaining the same light level for brighter spots to even out the overall brightness of images with high contrast between bright and dark spots. 1. When the SETUP menu screen is displayed, select „SSDR‟ by using the button so that the arrow indicates „SSDR‟. 2. Use the button to change the SSDR level according to the contrast between bright and dark areas.
※ The five white balance control modes are as follows. ▶ ATW (Auto Tracking White Balance): Select This when the color temperature is between 1800°K and 10500°K ▶ AWC→SET (Auto White balance Control): To find the optimal setting for the current luminance environment in this mode, set the point the camera towards a sheet of white paper and press the SET button. If the environment changes, readjust it. ▶ OUTDOOR: Select this when the color temperature is between 1800°K and 10500°K.
BACKLIGHT When there is a strong backlight behind the object, clear images of the Background as well as the object can still be obtained by using the BACKLIGHT function. MAIN SETUP SSDR ON ↙ WHITE BAL ATW BACKLIGHT OFF MOTION DET OFF FOCUS ↙ EXPOSURE ↙ SPECIAL ↙ RESET EXIT 1. Please position the arrow to point to 'BACKLIGHT' on the SETUP menu by using the UP and DOWN buttons. 2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
Enhancement level. Select „HLC‟ to adjust the HLC MASK TONE and LEVEL. ☞ Notes Since the following symptoms may occur according to the ambient illumination when BLC is selected, set it to OFF. 1 Color or screen changes unnaturally. ○ 2 Noise appears in the bright part of the screen. ○ Since the performance of the BLC function may be affected by the area of the bright part of the screen, optimize the installation angle for the best BLC performance.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button. MAIN SETUP SSDR ON ↙ WHITE BAL ATW BACKLIGHT OFF MOTION DET OFF FOCUS ↙ EXPOSURE ↙ SPECIAL ↙ RESET EXIT ① Please press the SETUP button. - OFF : MOTION DETECTION mode is cancelled. - ON : Any motion in the selected areas is observed. ▶ AREA SEL : Select the area user wants to observe in the 8 areas ▶ AREA MODE : Select to appear the word “ MOTION DETECTED” on the screen.
• START ZOOM : Use the left or right button in the „START ZOOM‟ item to select the zoom position from 1x to 27x (or 33x) to be returned after the „SMART ZOOM‟ action is over. • TARGET ZOOM : Use the left or right button in the ‟TARGET ZOOM‟ item to select the zoom position from 1x to 27x (or 33x) to be used during motion detection.
• ONE PUSH : Focus is automatically adjusted just once, after zoom position is changed. Select 'ONE PUSH' and press the SET button to confirm. Increase or decrease optical zoom (ZOOM) or digital zoom (D-ZOOM) positions by using the directional buttons while verifying the changes on screen. Press the SET button once desired image quality is obtained. • AUTO : Select AUTO and press the SET button to confirm.
• AUTOTRACK: Zooming in while deciding or adjusting the status of the focus. • TRACK: Zooming in with no relevance to the focus. • OFF: Only the zoom lens moves. ▶ ZOOM SPEED : Configure zoom tracing speed by using this feature. Position the indicator over 'ZOOM SPEED' by using the UP or DOWN button and then set todesired mode by using the LEFT or RIGHT button. FAST : To move zoom fast. MEDIUM : To move zoom at medium speed. SLOW : To move zoom slowly.
☞ Notes When the DIS is enabled, you cannot use the D-ZOOM. ▶ ZOOM POS INIT : Moves to the controlled ZOOM position when the power truned on and is a function of the initial ZOOM position control. AUTO : If you turn the power off and on, the zoom magnification level is set to the previous level that was set before the power went off. MANUAL : The zoom magnification level can be set from 1x to 27x (or 33x, 37x).
● ● ● ● PRESET NO : Up to 128 preset configurations are supported. PRESET SAVE : Save configured preset. PRESET CLEAR : Clear configured preset. END : Revert to the FOCUS SETUP menu. ▶ LENS INIT : Use the left or right button in the „Lens initialization‟ item to select „Automatic‟ or „Manual‟ and press the SET button to set up the initialization of the lens. • AUTO : The lens is initialized by setting the date.
MAIN SETUP SSDR ON ↙ WHITE BAL ATW BACKLIGHT OFF MOTION DET OFF FOCUS ↙ EXPOSURE ↙ SPECIAL ↙ RESET EXIT ▶ BRIGHTNESS : Use this feature to adjust image brightness. Position the indicator over 'BRIGHTNESS' using the UP or DOWN button. Then increase or decrease brightness level by using the LEFT or RIGHT button while verifying the changes on screen. Set END once desired level is obtained. ▶ IRIS : Set 'IRIS' to 'AUTO' or 'MANUAL'.
• AUTO: The iris is automatically activated upon illumination. • MANUAL: Manual iris configuration. Set 'IRIS' to 'MANUAL' by using the LEFT or RIGHT button and then press the SET button. Increase or decrease iris level by using the LEFT or RIGHT button while verifying the changes on screen. ▶ SHUTTER : Control image brightness by adjusting shutter speed. ① Position the indicator over 'SHUTTER' by using the UP or DOWN button. Then select the desired shutter mode (A.
• A.FLK (NTSC: 1/100, PAL: 1/120): Flicker-free mode. • ESC : Automatic shutter speed setting (optimal). Auto operation is possible only when the IRIS is set to MANUAL. • MANUAL : Manual shutter speed setting. If you choose „MANUAL‟, select the optimal shutter speed. · In MANUAL mode, the optimal shutter speed needs to be designated. Select from 1/60 to 1/120,000 (NTSC) or from 1/50 to 1/120,000 (PAL). ② * 'Sens-Up' mode can be configured manually (2x to 512x).
• MEDIUM • LOW • MANUAL • OFF : MEDIUM range gain value adjustment : Narrow range gain value adjustment : Selecting gain value range.(5dB~41dB) : Disabled ▶ SSNR3 : On screen noise reduction. ① ② Position the indicator over 'SSNR' by using the UP or DOWN button. Set 'SSNR' to the desired mode by using the LEFT or RIGHT button • OFF : Disabled. • LOW : Low noise reduction. • MEDIUM : MEDIUM noise reduction. • HIGH : High noise reduction.
• SSNR function is disabled in AGC mode „OFF‟. ▶ Sens-UP: This feature ensures clear images at night or under low lighting conditions. ① ② ③ Position the indicator over 'SENS-UP' using the UP or DOWN button. Set 'SENS-UP' to the desired mode using the LEFT or RIGHT button. Select SET button is AUTO mode then, SENS-UP limit can be adjusted from x2~ x512. • AUTO: Select this mode for use in night time or under low lighting conditions. • OFF: Disabled ☞ Notes • SENS-UP doesn‟t work when AGC mode off.
SPECIAL 1. Press the SET button to access the main setup menu and then position the indicator over 'SPECIAL' using the UP or DOWN button. 2. Press the SET button to confirm. SPECIAL SETUP PRIVACY OFF DAY/NIGHT AUTO↙ DIS OFF SYNC INT COMM ADJ ↙ IMAGE ADJ ↙ MONITOR CRT↙ DISPLAY RETURN ▶ PRIVACY: Mask privacy area by using this feature. The mask area expand/contract upon the zoom position.
• AREA MODE Mask area display. - TOP : To move the mask area up. - BOTTOM : To move the mask area down. - LEFT : To move the mask area left. - RIGHT : To move the mask area right. • MASK COLOR Adjust desired mask color level. • MASK TONE Adjust desired mask transparency level. • END Select this to save the PRIVACY menu settings and return to the SPECIAL menu. ▶ DAY & NIGHT : Select from COLOR, BW or AUTO modes.
☞ Notes • When “AGC” is set to “OFF”, AUTO MODE cannot be used but, only use “COLOR MODE” and “B/W MODE”. • When Use B/W mode under Sunlight or Halogen Lamp, the focus may be smear than normal light. ▶ DIS : The DIS mode can compensate for vibration of the camera. ☞ Notes • When DIS is operating, D-ZOOM does not operate. ▶ SYNC : Apply INIT mode. • INIT : Internal synchronization ▶ COMM ADJ : Use this feature to select communication protocol.
▶ IMAGE ADJ : Includes image quality or special function factors. 1 When the SETUP menu screen is displayed, select „IMAGE ADJ‟ by using the Up and ○ Down buttons so that the arrow indicates „IMAGE ADJ‟. 2 Selected a desired mode using the Up and Down buttons. ○ • H-REV : Use this feature to horizontally inverse the screen. • V-REV : Use this feature to vertically inverse the screen. • SHARPNESS : Increasing this value sharpens object edges.
▶ DISPLAY: Includes image quality or special function factors. • CAM TITLE : Use this feature to designate a name for the camera, which will display on the monitor screen. ①Press the SET button to display the main setup menu and move the arrow indicator to 'CAM TITLE' by using the UP or DOWN button. ②Set 'CAM TITLE' to 'ON' by using the LEFT or RIGHT button. ☞ Notes • If the CAM TITLE feature is set to 'OFF', the name will not displayed in the monitor. ③Press SET button. ④You can enter up to 20 characters.
⑤Select on screen position of the CAM TITLE. a. Move the cursor to 'POS' and press SET button. b. The CAM TITLE is displayed on the top-left of the monitor screen. (Default position) c. Select the position by using the 4-directional buttons, then press the SET button to confirm the position. ⑥When completed, move the cursor to 'END' and press SET button. • CAM ID : Displays camera ID on top left corner of the screen. • CAM INFO : Displays camera information on screen.
• LANGUAGE : You ca n select the menu language according to your requirements (ENGLISH, Chinese, DEUTSCH, ITALIANO, FRANCAIS, ESPANOL, Korean, Japanese, PORTUGUESE ) • END : Select this to save the DISPLAY menu settings and return to the SPECIAL menu. RESET To reset your camera to factory default condition. ☞ Notes • Some in „COMM ADJ‟ mode can not be reverted even if it is RESET. EXIT To finish setup menu.
7. Troubleshooting Problem Solution No display • Check the power cable and the wiring between the camera and the monitor. • Ensure proper video cable connection (Video Out Jack). Dim display • The lens could be dirty. Clean with a soft, clean piece of cloth. • Adjust monitor settings. • Adjust camera position if exposed to a strong light source. Dark display • Adjust the monitor's contrast level.
8. Specifications Signal system Image Sensor Total Pixels Effective Pixels Resolution Scanning Frequency Scanning System Shutter Speed Min. Illumination Zoom Rate Digital Zoom DIS Min. Focus Distance Angle Field of view Back Light SSDR Day & Night Privacy Zone AGC Camera ID White Balance SSNR OSD Flip / Mirror Communication S/N Ratio Video Output Sync. System Operating Humidity Operating Temp.