HIGH SPEED DOME CAMERA User Manual 600 TVL
Table of contents Ⅰ CAUTION --------- 4 Ⅱ INTRODUCTION OF PRODUCTS --------- 6 Ⅲ DIRECTIONS FOR USE --------- 14 Ⅳ FUNCTIONAL SETTING BY THE KEYBOARD --------- 27 Ⅴ OSD MESSAGE DISCRIPTION --------- 30 Ⅵ TROUBLE SHOOTING --------- 32 Ⅶ DIMENSION --------- 34 Ⅷ ASSEMBLY --------- 36 Ⅸ SPECIFICATION --------- 39 3
Ⅰ. CAUTION Thank you for purchasing our product. Please operate the product after being fully aware of the manual. Pease contact us if you have any queries. Precaution Note the following matters before the installation of the product. Avoid the following places for the installation. A high/low temperature: Using indoor-cameras Snow, rain and wet: Humidity or water and in the places of +50°C~ -10°C can cause any liquid inside-camera can cause troubles. troubles and lower its capacity.
Caution in Use Do not disassemble the unit and put alien substances in the unit. - Disassembling the unit or putting alien substances such as a metal can make the camera defective. - Make sure of power switch-off before the installation. : Ensure power switch-off and check the voltage the camera before the installation. - Do not give the unit a shock and an operation. : Giving a strong shock or an excessive power on the button, terminal can cause problem.
Ⅱ. INTRODUCTION OF PRODUCT 1. DESCRIPTION AND FEATURES Description This camera has been designed elegantly for buildings, department stores that need to be in harmony with the interior as a high speed dome camera, including various observation functions. Features ☺ High Resolution and Zoom Rate High resolution 600 TVL and Built-in High Zoom ( 27X, 33X, 37X )Rate Camera with 16x Digital Zoom ☺ A low light function Surveillance with optimum picture is possible owing to digital-slow-shutter function.
2.
2) Installation Indoor Type Outdoor Type SEPARATION OF LOWER COVER (Indoor type) Loosen the bolt of the back of lower cover by a screwdriver(+), then turn the cover as above the picture and pull the lower cover to the down (Outdoor type) Loosen the four bolts of the lower cover, then separate. Loosen the three bolts, the round head shaped, of the camera body. The three bolts are not loosened completely and not come up more than 1cm of the lower cover, then separate.
Open the connector cover, then connect power, data, video cable and sensor The cover is opened if user loosens the one bolt on the connector cover by using a screwdriver(+). The bolts not loosened completely to protect from missing of them.
3) How to connect equipments DC12V/1A adaptor and junction box are provided on a purchase, Junction box consists of 2 data ports ( Each data port can be connected with maximum up to 128 cameras and sub keyboard terminal Connect the image line of a monitor Reference to the following page. User can control maximum up to 255 cameras connected by using the exclusive control keyboard. User can connect it maximum up to 1.
Alarm output is tangency output of relay non-load, it can be used up to AC220/10A by connecting the load. The switch is automatically turned on when the sensor works and it is possible to cancel by using the controller after a limited The sensor time Can be connected maximum 4 channels and the camera can be moved automatically to the point by preset mode, DATA Can be processed by RS485 or RS422 and use parallel connection to use a large quantity of cameras.
4) HOW TO SET PROTOCOL You have to change this switch when you Use to change this switch Protocol change protocol and communication speed ADDRESS O O 4 I P I N 2 N A N 2 I L T T 4 A N E M 8 D T X ON F O OFF 1 2 3 4 5 6 7 8 S1 The switch to select protocol The switch Change No.
5) SETTING ADDRESS OF DIP SWITCHES.
Ⅲ. DIRECTIONS FOR USE ● OSD (ON SCREEN DISPLAY) menu control It is the function to call up the Menu ＊User can not only set Preset, Group, Tour, Swing, Trace functions of the camera up by the menu, but also set them up by shortening keys. ● Accessing OSD menu ● The menu is displayed on the screen with the key tone when user presses No.1 and menu key. ◄◄ CAMERA SETUP p1 ►► 1. ID Set : CAM-001 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Max 5. Shutter speed. : AUTO 6.
1. ID SET. ◄◄ CAMERA SETUP p1 ►► 1. ID Set : CAM-001 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Max 5. Shutter speed. : AUTO 6. Sharpness level :6 7. Brightness :9 8. Flickerless : OFF 9. DNR Control : Medium - NEXT MENU PAGE This function is to set camera ID up to 16 letters on the monitor.
5. SHUTTER SPEED ◄◄ CAMERA SETUP p1 ►► 1. ID Set : CAM-001 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Max 5. Shutter speed. : AUTO 6. Sharpness level :6 7. Brightness :9 8. Flickerless : OFF 9. DNR Control : Medium - NEXT MENU PAGE ◄◄ CAMERA SETUP p1 ►► 1. ID Set : CAM-001 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Max 5. Shutter speed. : AUTO 6. Sharpness level :6 7. Brightness :9 8. Flickerless : OFF 9.
◄◄ CAMERA SETUP p1 ►► 1. ID Set : CAM-001 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Max 5. Shutter speed. : AUTO 6. Sharpness level :6 7. Brightness :9 8. Flickerless : OFF 9. DNR Control : Medium - NEXT MENU PAGE ◄◄ CAMERA SETUP p2 ►► 10. Back Light : WDR Mode 11. Set Back Light Mode 12. White Balance : Auto 13. Focus Mode :Oneshot 14. Zoom Max Limit : Off 15. DSS Control : 10 Field 16. Day&Night : Auto+Hi 17. Stabilize On/Off : Off - PREV MENU PAGE - NEXT MENU PAGE 9.
After complete all setup, press F/N button, and then move to RETURN MENU PAGE. It is automatically saved. ◄◄ CAMERA SETUP p2 ►► 10. Back Light : WDR Mode 11. Set Back Light Mode 12. White Balance : Auto 13. Focus Mode :Oneshot 14. Zoom Max Limit : Off 15. DSS Control : 10 Field 16. Day&Night : Auto+Hi 17. Stabilize On/Off : Off - PREV MENU PAGE - NEXT MENU PAGE ◄◄ CAMERA SETUP p2 ►► 10. Back Light : WDR Mode 11. Set Back Light Mode 12. White Balance : Auto 13. Focus Mode :Oneshot 14.
◄◄ CAMERA SETUP p2 ►► 10. Back Light : WDR Mode 11. Set Back Light Mode 12. White Balance : Auto 13. Focus Mode :Oneshot 14. Zoom Max Limit : Off 15. DSS Control : 10 Field 16. Day&Night : Auto+Hi 17. Stabilize On/Off : Off - PREV MENU PAGE - NEXT MENU PAGE 16. DAY& NIGHT The function is used to distinguish an object clearly in the dark condition.
◄◄ CAMERA SETUP p3 ►► 18. Select Alarm : Sensor 19. Motion Detection : Off 20. Preset Set & Run Page 21.Trace Set Page 22. Alarm CH On/Off Page 23. Alarm Preset Set Page 24. Privacy Zone Set Page - PREV MENU PAGE - NEXT MENU PAGE 20. PRESET SET & RUN PAGE It is a function to set and operate Preset, Group, Tour. User can see the screen when moves the joystick to Right/Left after fixing the cursor on the menu. <> ① Preset set CH : User can set Preset No. and title on this menu.
③ Preset Swing SET : Set Preset Swing Move next SWING page for the setting, if user presses F/F key in the state of selection of the menu ※The preset must be set before the setting as Swing Is a function to repeat an auto observation of 2 Preset points user fixes in Preset set ④ GROUP SET: User can set maximum 12 groups. Select a channel then move to next page after pressing F/F key ※The Preset point in the Group that 12 Preset points are set is observed repeatedly and order with regular speed and time.
⑤ Tour SET Group: User can set continual Group motion that can be put 12 Groups in 1 Tour Move to the setting page if user presses F/F key on this menu ■ The Group user wants to set must be set firstly ※Setting is only possible when Preset is set first in the state of setting of Swing, Group, Tour, otherwise, it displays the message “Sorry Undefined”. ⑥ Run Function: Operate one of SWING/ ＊Set / Stop order with a control keyboard without menu GROUP / TOUR / TRACE. (It is operated on the screen.
22. ALRAM CHANNEL ON/OFF ◄◄ CAMERA SETUP p3 ►► 18. Select Alarm : Sensor 19. Motion Detection : Off 20. Preset Set & Run Page 21.Trace Set Page 22. Alarm CH On/Off Page 23. Alarm Preset Set Page 24. Privacy Zone Set Page - PREV MENU PAGE - NEXT MENU PAGE - CH On/Off : Alarm Input – Each channel can be ON/OFF - Alarm Relay : It can be set On or not when ALARM OUTOUT PORT operate wrong. - Active Alarm : It selects ACTIVE OPEN or ACTIVE CLOSE by tangency when something is wrong.
※You can set ALARM setting MENU not only in CAMERA SET MENU MODE, but also a KEYBOARD in direct 24. PRIVARCY ZONE SET ◄◄ CAMERA SETUP p3►► 18. Select Alarm : Sensor 19. Motion Detection : Off 20. Preset Set & Run Page 21.Trace Set Page 22. Alarm CH On/Off Page 23. Alarm Preset Set Page 24. Privacy Zone Set Page - PREV MENU PAGE - NEXT MENU PAGE ☞ This function does not work on 27X speed dome camera. Max 16 privacy zones can be configured for the protection of privacy.
◄◄ CAMERA SETUP p4►► (27x -33x/37x) 24 - 25. Auto Tilt Mode : Off 25- 26. Smart Pan/tilt : ON 26- 27. Manual P/T Speed : Medium 27- 28. Auto Refresh Time :1day 28- 29. Shortcut Key : On 29- 30. Use Password :Off 30- 31. Language :English 31- 32. Factory Reset Warning - PREV MENU PAGE 24-25. AUTO TILT MOVE ◄◄ CAMERA SETUP p4►► (27x -33x/37x) 24 - 25. Auto Tilt Mode : Off 25- 26. Smart Pan/tilt : ON 26- 27. Manual P/T Speed : Medium 27- 28. Auto Refresh Time :1day 28- 29. Shortcut Key : On 29- 30.
◄◄ CAMERA SETUP p4►► (27x -33x/37x) 24 - 25. Auto Tilt Mode : Off 25- 26. Smart Pan/tilt : ON 26- 27. Manual P/T Speed : Medium 27- 28. Auto Refresh Time :1day 28- 29. Shortcut Key : On 29- 30. Use Password :Off 30- 31. Language :English 31- 32. Factory Reset Warning - PREV MENU PAGE 28-29. SHORTCUT KEY The Shortcut Key can make some of the functions to perform faster and easily.
◄◄ CAMERA SETUP p4►► (27x -33x/37x) 24 - 25. Auto Tilt Mode : Off 25- 26. Smart Pan/tilt : ON 26- 27. Manual P/T Speed : Medium 27- 28. Auto Refresh Time :1day 28- 29. Shortcut Key : On 29- 30. Use Password :Off 30- 31. Language :English 31- 32. Factory Reset Warning - PREV MENU PAGE 31-32. FACTORY RESET WARNING Please be careful of that all setting data of OSD MENU are reset into the first default when operates FACTORY RESET WARNING.
Ⅳ. Functional Setting by the Keyboard 1. Preset setting You can set Preset point up to 250. ① Preset Input. Preset setting can be set 1 to 250 sequentially after moves the camera to where you want ② Preset Move The camera moves to the preset point, if you press Preset No.
② Operation of Swing (Run Pan) ③ End of Swing (Run Tilt) 3. Group setting ① Start Group setting mode Start the Group Select the Group in 1~12 Select in Preset No.1~250 setting mode and input them. Move Speed: The Speed from A to B 64=High, 1=Low Dwell Time: The dwell time at the point of A or B before the move. (sec) - Set Preset No. again if you want to input it continuously.
■ Repeat input in continual input EX). Register Group No. 1, 3, 6 as Tour Start Register Register Register Finish Tour mode Tour No.1 Tour No.2 Tour No.3 Tour mode ② Start / End Tour ③ Delete Tour Start Tour Finish Tour 5. Spiral Function It is a function to observe objects in the spiral direction. ① Spiral observation ‘ON’ ② End 6. PTZ Trace It memorizes P/T/Z motions for 200sec, then operates them at the same Trace.
Ⅴ. OSD MESSAGE DISCRIPTION 1. PRESET MESSAGE CAM-001 SET PST 001 User can PRESET 001 check that preset No.1 is saved as an appeared CAM-001 message It is CAM-001 CLEAR PST 001 displayed when moving to the preset No.1 in It is displayed when user deletes preset No.1.
CAM-001 CAM-001 CAM-001 TOUR&GP:01 PRESET:001 CLEAR TOUR & GRP As the message in the time As the message in the It shows the data in group of operation of Tour set, time of operation of tour and tour saved was deleted. “GP:01” means group No.1 run, and it shows that group No.1 moving to preset No.1 in was saved. group No.1 SET TOUR GP:01 it will show that CAM-001 RUN SPIRAL RUN SPIRAL : It is the message in the time of operation of spiral sequence.
Ⅵ. TROUBLE SHOOTING 1. You must turn off the power switch before installation of this equipment 2. Avoid installation places where it is the ultimate cold, hot, and humid. 3. Use a power supply of AC24V, 1.5A output. 4. Please be careful that you connect respective wires without mismatching in installation. 5. Check the controlled cable’s insulation connecting to exterior and supply to power sources. 6.
When it occurred alarm state, it is not Did you set the preset in the set Check setting status of the alarm exactly presser position or different. mode? preset in the set mode. When it activate alarm state, there is Did you use the exclusive control It is need to use an exclusive control no sign on the keyboard controller keyboard? keyboard so that the alarm sound is activated on the controller Yes, I do. Please select on to enable alarm of the related camera.
Ⅶ.
Ceiling mount bracket Indoor Type Outdoor Type In-ceiling mount bracket 36
Ⅷ. ASSEMBLY DSC-30EWP Wall mount bracket ① Remove the body of main camera from the housing ③ Fix the upper cover into a wall bracket with turning it in the same direction as the picture ④ Connect the data cable, video cable and power source cable. ② Fix four bolts after connecting each line and block up the hole of the bracket’s body with 34mm block rubber.
DSC-20ECP Wall mount bracket Assembly of outdoor dome with pole mount pendant 1 Remove the 3 Main body of The camera Turn the ceiling From the Housing. pole to connect. Fix the pole 2 box on the 4 ceiling. Turn the joint 5 Turn the cover coupler to connect. 6 7 Connect the cover coupler with the Connect the data lines. housing and fix it Connect the video lines. 9 8 Unite the clear Rejoin the main bubble with the body of the camera housing. to the housing. 38 coupler connect.
Main & Sub Keyboard configuration 39
Ⅸ. SPECIFICATIONS MODEL 27X Zoom □ 33X Zoom □ 37X Zoom □ Image sensor 1/4” Sony Super HAD CCD Effective pixels NTSC 768(H) X 494(V), PAL 752(H) X 582(V), Horizontal resolution Color : 600 TVL, B/W 700 TVL 27x Optical zoom(16x), 33x Optical zoom(16x), 37x Optical zoom(16x), f =3.5 –94.5mm f =3.5 –115.5mm f =3.5 –129.5mm H : 55.5° ~2.24° , V : H : 55.5° ~1.77° , V : H : 55.5° ~1.59° , V : 42.5°~1.79° 42.5°~1.33° 42.5°~1.19° Lens (Digital Zoom) Angle of view Minimum illumination 0.
1
2
3
DISTRIBUTED BY 4
