High Resolution / Day & Night COLOR DOME TYPE CAMERA MANUAL 680 TVL 960H, UTC, Defog
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
■ Warning The camera needs periodic inspection. Contact an authorized technician for inspection. Stop using your camera when you find a malfunction. If you use your camera around smoke or unusual heat for a long time, fire may be caused. Do not Install the camera on a surface that can not support it. Unless the surface is suitable, it could cause falling or other hazards. Do not hold plug with wet hands. It could cause an electric shock. Do not disassemble the camera.
■ Precautions Only use the camera under conditions It can cause the image quality to be where temperatures are between poor. -10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures. Severe lighting change or flicker can It is one of the most important parts of cause the camera to work improperly. the camera. Be careful not to be stained by fingerprint. It can cause malfunctions to occur. It can damage the CCD. If it gets wet, wipe it dry immediately.
■ Contents 1.Features 2. Cable Connection & OSD Control 3. Setup Menu Operation 4. Troubleshooting 5. Dimensions 6.
1. Features ■ 1/3" 520K/610K Sony Super-HAD CCD II Minimum Low Illumination (F1.2, 50 IRE) ■ High Resolution 680 TV Lines This camera has realized high resolution of 680 TV lines using the top-notch full digital image processing, 10 Bit A/D serial signal processing and special algorithm technologies. ■ DNR(Digital Noise Reduction) The DNR technology removes low-light gain noise and afterimage to provide distinct and clear images even in dark environments.
2. Cable Connection & OSD Control 1) Cable Connection 2) OSD Control ① 3AXIS BRACKET - Please loosen screws and fix tilted and panned position. ③ LENS : Vari-Focal Auto Iris Lens ③ OSD PCB - SETUP button : Used for the menu display. This button can be used to confirm settings after changing the value of the selected function or current conditions. - UP & DOWN buttons : Used for selecting items by moving the cursor up or down on the menu screen.
3. Setup Menu Operation ◆ Menu configuration CAMERA SET CAMERA TITLE CAM ID ID DISP FONT COLOR COMMUNICATION LANGUAGE LENS BRIGHTNESS SHUTTER FLK AGC AUTO NIGHT DAY ATW MANUAL PUSH GAMMA CHROMA SHARPNESS SHADING PED. LV. BLACKLIGHT CONTRAST H-MIRROR PRIVACY LOW HIGH MIDDLE SENSITIVITY AREA NO. AREA USE TOP BOTTOM LEFT INITIAL RESTORE VERSION EXPOSURE DAY/NIGHT WHITE BAL. MONITOR IMAGE DNR MOTION EXT.
■ CAM TITLE Make a set camera title using below numbers and alphabets (0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,G,H,I,J,K,L, M,N,O,P,Q,R,S,T,U,V,W,X,Y, Z) ◇OFF: disable CAMERA TITLE. ◇ON: display CAMERA TITLE. ■ CAM ID You can set CAMERA number from 1 to 255. ■ ID DISP ◇OFF: disable CAMERA NO/ID. ◇ON: display CAMERA NO/ID ■ FONT COLOR You can set CAMERA OSD Color. (white, cyan, green, magenta, red, blue, yellow, gray) ■ COMMUNICATION (COAXIAL) This camera can be adjust by remote controller via coaxial.
◇ BRIGHTNESS(1~20) The BRIGHTNESS menu is used to adjust the overall brightness, where "▶" will increase the brightness and "◀" will decrease it. ◇ SHUTTER The SHUTTER menu is used to set the fixed high-speed electronic shutter, auto high speed electronic shutter. You can select one of 13 options from 1/100( PAL:1/120 ) for the fixed high speed electronic shutter, which is mostly used for imaging a fast moving object. You can select one of shutter speed, 1/120(1/100), 1/250, 1/500, 1/700, 1/1K, 1/1.6K, 1/2.
◆ DAY/NIGHT(AUTO, DAY, NIGHT, EXT) ■ AUTO The camera will automatically switch between DAY and NIGHT mode, according to the lighting condition. If you press the ⓔ( Enter ) switch with an AUTO based sub menu selected, you will see the appropriate screen. ◇ AGC THRESHOLD Set AGC THRESHOLD that is standard value of the AGC gain, when changing from DAY to NIGHT or from NIGHT to DAY. ◇ AGC MARGIN: Set AGC MARGIN. ◇ DAY & NIGHT DELAY TIME: Set day/night switching delay time.
■EXT. This enables to switch between DAY and NIGHT mode using the interface with external signal. ◆ WHITE BAL.(White Balance) Use the White Balance function to adjust the screen color. ◇ ATW The camera can automatically adjust the color temperature in real time, according to the ambient conditions. The color temperature ranges from 2,000K ~ 10,000K.
◇ PUSH If you press the ⓔ( Enter ) switch in the appropriate item position, Auto White Balance will perform once. ◇ MANUAL In this mode, you can set the color temperature of RED and BLUE. ◆ MONITOR Please change the settings value of video appropriate to your monitor. ◇ GAMMA 0.4,0.45,0.5,0.55,0.6,0.
◇ CHROMA: Color Gain Set ◇ SHARPNESS: Aperture (Horizontal,Vertical) Set ◇ SHADING: Lens Shading ◇ PED. LV.:Pedestal Level Set ◆ IMAGE ■ BACK LIGHT ◇ BLC Adjusts the area to be enhanced and sets the level. ◇ HLC If the scene contains extremely bright light areas such as; from car headlight, the light can mask out much of the on-screen detail. - LEVEL: Adjusts the brightness level of a monitoring area.
■ CONTRAST ◇ D-WDR When there are both bright and dark areas at the same time, this mode makes both areas distinctive. ◇ DEFOG This camera supports DEFOG function which does a process of clearing blurred image caused by fog and snow by analyzing the brightness of input image and compensating the color of the image ◇ POSI / NEGA Switch to negative color.
■ H - MIRROR ◇ H – MIRROR You can flip the picture - MIRROR: Horizontal reverse pictures on the monitor. ◇ PRIVACY You may conceal specific area on the screen with this ‘PRIVACY’ function. You can set masking areas up to 8 zones. ◆ DNR(Digital Noise Reduction): OFF, LOW, MIDDLE, HIGH You can configure the DNR(Digital Noise Reduction) related settings. It reduces the noise on the screen. This is especially useful for a severely distorted screen ◆ MOTION You can specify a detection area.
◇ SENSITIVITY Set the sensitivity of the motion detection from 0(Highest) to 15(Lowest). ◇ AREA NO Specify a detection area. You can set the area from 1 to 4. ◇ AREA USE With the DISPLAY option set to ON, a motion function will be displayed on the screen, if detected. ◇ TOP/ BOTTOM/LEFT/ RIGHT -. TOP: extends or reduces upper detection area. -. BOTTOM: extends or reduces lower detection area. -. LEF: extends or reduces detection area on the left. -.
4. Troubleshooting If there are problems in operation, please refer to the items below. If the problem persists, please contact the agent you purchased this product from . Problems Nothing appears on the screen. Troubleshooting • Please check the power connection. • Please check the video signal line connection. • Please check and make sure that the auto lens switch is set to DC (VIDEO) when using a VIDEO(DC) lens. The video image is not clear. • Please check if the lens is clean.
5.
N4 VANDAL DOME CAMERA N5 N6 20
IR DOME CAMERA N7 IR VANDAL DOME CAMERA N8 21
6. Specifications ▪ GENERAL Signal system NTSC PAL 1/3” 960H Super HAD Sony CCD∥ Image Sensor Total Pixels 1028(H)X508(V) 1028(H)X596(V) Effective Pixels 976(H)X494(V) 976(H)X582(V) Resolution Scanning Frequency 680 TV lines (B/W 750 TV Lines with ICR) 15.734KHz(H), 60Hz(V) Min. Illumination Day & Night OSD 15.625KHz(H), 50Hz(V) 0.
Dome type 1 2 3 4 Indoor Indoor Indoor Indoor 120x95(H) 100x103(H) 81x87(H) 2 Axis 2 Axis 3Axis 3Axis Plastic Body & Plastic Body & PC Bubble & PC Bubble & Bubble Bubble Plastic Body Plastic Body 300g 560g 600g 300g Max 1.8W Max 2.5W Max 2.5W Max 2.5W Number Install Type Dimension(mm) 100x76.5(H) 3 Axis Material Weight Power Consumption Power DC12V DC 12 V 500mA(10.2V~14.5 V) Supply (10.2V~14.