Digital Day & Night COLOR CAMERA USER MANUAL
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER WERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Warning The camera needs periodic inspection. Contact an authorized technician for Contents 1. Features 4 2. Components & Cable Connection 6 3. Names and functions of parts 7 inspection. Stop using your camera when you find a malfunction. If you use your camera around smoke or unusual heat for a long time, fire may be caused. Do not Install the camera on a surface 4. Installation & Dimension 10 5. Setup Menu Operation 16 6. Special Menu operation 27 7. Troubleshooting 36 8.
1. Features Horizontal Resolution 530 TVLines Clear image quality has been achieved by employing a SONY CCD with 410,000 (effective) pixels, which provides a horizontal resolution of 530 TV lines. DAY & NIGHT This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions The COLOR mode operates in daytime conditions to provide optimum colors, and BW mode operates in nighttime conditions to enhance the definition of the image.
2. Components 1) COLOR CAMERA 3. Names and Functions of Parts DAY & NIGHT, DSS 00F DCC-5CAMERA R N COLO LUTIO HIGH RESO T, DSS NIGH DAY & 00F DCC-5CAMERA LOR N CO LUTIO HIGH RESO 2) AUTO IRIS LENS CONNECTION PLUG 1) Front 3) C-MOUNT ADAPTOR Lens protection cap Please cover the lens when not using it. CS-Mount lens adaptor Please attach the CS-Mount lens here. Back Focus clamp screw Please loosen the clamp screw with a screwdriver before adjusting the Back Focal length.
The mounting bracket can be separated and attached to the top of the camera. In this instance please do not tighten the screw to a depth of more than 5mm, otherwise serious damage can occur to the inside of the camera. 2) Back ¶ Power lamp Lights up when the correct power is supplied to the camera. Setting button SETUP button : Used for the menu display. This button can be used to confirm settings after changing the value of the selected function or current conditions.
4. Installation 1) Lens Lenses are sold separately. Lenses such as auto iris lens, CS-Mount lens and C-Mount lens can be used. Note Use of the DC auto iris lens is recommended to achieve the best results for operating this product effectively. Please keep the lens clean. Any foreign objects and fingermarks on the lens can cause inferior image quality in low light level conditions. - Please remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug.
then attach the auto iris lens to the camera by screwing it in clockwise. - Please insert the connection plug that is connected to the auto iris lens cable into the auto lens connector, which is located on the back of the camera When using a CS-Mount lens Please take off the lens protection cap and attach the CS-Mount lens to the camera by screwing it in clockwise.
Note Please use the specified lens connection parts as shown in the picture below. The use of the wrong sized parts may cause damage to the inside of the camera or result in poor fitting. Use of a lens which is too heavy affects the balance of the camera and may cause a malfunction. Please use a lens that weighs less than 450g. Please select Av mode if possible when adjusting the automatic light control (ALC) of an auto lens. Use of PK mode may cause hunting the type of monitor and accessories.
5. Setup Menu Operation SETUP Select any function you wish to operate by using the UP and DOWN buttons. 1) Settings SETUP MNUAL ESC ATM OFF LOW LOW OFF The arrow can be moved up or down by using the UP and DOWN buttons. Please position the arrow to point to the function you wish to operate. 16 MNUAL ESC ATM OFF LOW LOW OFF Modes can be changed using the LEFT and RIGHT buttons. Please press the LEFT or RIGHT button if you wish to change mode.
When the SETUP menu is displayed on the screen, please position the arrow to point to 'LENS' by using the UP and DOWN buttons. Please select the type of the lens you wish to use by pressing the LEFT or RIGHT Button Please press the SETUP button if you wish to return to the previous menu MANUAL : Manual lens selection DC : Auto iris lens selection SETUP LENS SHUTTER WHITE BAL BACKLIGHT AGC DNR SENS-UP SPECIAL EXIT DC ESC ATM OFF LOW LOW OFF Note The brightness of the screen can be adjusted in DC mode.
Please select 'MANUAL' mode if you wish to adjust the shutter manually. - You can select speed from '1/60' to '1/120,000'sec (NTSC Models), '1/50' to '1/120,000'sec (PAL Models). Please press the SETUP button when all the settings are complete. Note While using the internal synchronous system, if the shutter setting is on 'ESC' and the camera is directly facing a bright fluorescent light, the image on the screen can dirersely affected. Therefore please choose the installation location with care.
Note Under the following conditions the WHITE BALANCE function may not operate properly. In such cases, please select the AWC mode. When the object's surroundings have a very high color temperature (eg, a clear sky and sunset) When the object's surroundings are dark If the camera directly faces a fluorescent light or is installed in a place where there are considerable changes in illumination, the WHITE BALANCE function may become unstable.
As the level of gain increases, the screen gets brighter and the level of noise also increases. - HIGH : The gain increases or decreases within the range of 6dB ~ 42dB. - MIDDLE : The gain increases or decreases within the range of 6dB ~ 30dB. - LOW : The gain increases or decreases within the range of 6dB ~ 18dB. - OFF : The gain is fixed at 6dB. - MIDDLE : The most effective mode. There is a sufficient reduction in noise levels without causing much ghost imaging.
by pressing the SETUP button in 'AUTO' mode.(X2~X128) As the magnification increases, the screen gets brighter; however the after image also increases If storage magnification is increased while SENS UP is operating, it may cause noise, and spots may appear; however this is normal. AUTO : Low light level auto mode OFF : The function does not operate Note When SHUTTER is in the manual mode, SENS UP does not operate. When AGC is turned off, SENS UP does not operate.
Camera ID ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz -. 0123456789 CLR POS END ------------------------- Up to 15 letters can be used for the ID. - Please move the cursor to the letter you wish to choose by using the UP and DOWN button. Camera ID ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz -. 0123456789 CLR POS END ------------------------- - Select an ID from A,B~Y,Z, a,b~y,z, 0,1~8,9 by using the UP, DOWN,LEFT and RIGHT buttons.
SPECIAL ←→↑↓ Please find the position you wish to display the name by using the 4 directional buttons, and then press the SETUP button. CAMERA ID COLOR SYNC MOTION DET PRIVACY MIRROR SHARPNESS RESET RETURN OFF ON INT OFF OFF OFF ON ON : The color mode is selected by default, and the modes do not change Automatically. Note When the AGC is turned off, COLOR does not operate. When an infrared light is used, there may be a problem with focusing. 4) SYNC " Sync " mode is fixed to INT in DC12V input power.
individual can conduct supervision efficiently. The camera detects an object's movement by sensing disparity of outline, and level of brightness and color. Please press the SETUP button. - OFF : MOTION DETECTION mode is cancelled. - ON : Any motion in the selected areas is observed. Please select the area you wish to observe from the 4 areas in AREA SEL mode. Please select ON mode for the chosen area. Please adjust the size of the area to be observed by using the UP, DOWN, LEFT or RIGHT button.
Please adjust the size of the area to be concealed by using the UP, DOWN, LEFT Or RIGHT button. 7) MIRROR The outline of the video image becomes cleaner and more distinctive as the level of SHARPNESS increases. If the level goes up excessively, however, it may affect the video image and generate noise. SPECIAL CAMERA ID COLOR SYNC MOTION DET PRIVACY MIRROR SHARPNESS RESET RETURN OFF ON INT OFF OFF OFF ON ON : Sets a horizontal image inversion OFF : Cancels the inversion.
7. Troubleshooting If there are problems in operation, please refer to the items below. If the problem persists, please contact the agent you purchased this product from. Problems Troubleshooting The MOTION Please check if an appropriate power DETECTION source to the camera complies with the function is not manufacturer's standard requirement, or working. if the voltage keeps changing. Please check if 'MOTION DETECTION' mode is turned on.
8. Specifications SIGNAL SYSTEM TOTAL / EFFECTIVE PIXEL IMAGE SENSOR NTSC PAL 410K / 380K Pixels 1/3" SONY interline transfer CCD HORIZONTAL RESOLUTION MINIMUM ILLUMINATION 470K / 440K Pixels 530 TV Line 0.3 Lux / F 1.2, 0.01Lux with Sensitive Up DAY & NIGHT ON / AUTO OSD Available LENS CS Mount DNR OFF/LOW/MIDDLE/HIGH SENS-UP OFF / AUTO MOTION DETECTION LUMINANCE S/N RATIO ON / OFF More than 50dB (AGC Off) SYNC.
DISTRIBUTED BY