MINI SPEED DOME CAMERA MINI SPEED DOME CAMERA USER MANUAL DMS-200 DMS-200Se
TABLE OF CONTENTS 1. CATION ------------------------------------------------------- 3 2. INTRODUCTION OF PRODUCT -------------------------------5 1). DESCRIPTION AND FEATURES -----------------------------5 2). INSTALLING AND CONNECTING ---------------------------- 6 2-1. NAME AND FUNCTION OF EACH PART -------------------6 2-2. INSTALLATION --------------------------------------7 2-3. CONNECTION DIAGRAM --------------------------------8 3.
1. CAUTION Thank you for purchasing mini speed dome camera DMS-200. Please operate the product after being fully aware of the manual. Pease contact us if you have any queries or face any problems. DO NOT CONTROL PAN, TILT BY FORCE Do not move the inside Pan/Tilt motor by force after removing dome cover. It can cause damages. HANDLE WITH CARE OF CAMERA LENS AND DOME Be careful of handle with dome cover Please use a soft fabric due to a scratch when you clean the cover.
CAUTION IN USE. Do not disassemble the unit and put alien substances in the unit. It can cause troubles. Ensure power switch-off before the installation. Ensure power switch-off and check the voltage the camera before the installation. Do not give the unit a shock and an operation. Giving a strong shock or an excessive power on the button, terminal can cause troubles.
2. INSTRUCTION OF PRODUCT 1). DESCRIPTION AND FEATURES - Description This camera has been designed elegantly for buildings, department stores that need to be in harmony with the interior as a mini speed dome camera, including various observation functions. It moreover is effective for true Day & Night. - Features High magnification zoom lens 250 Preset positions Max 192 times zoom A maximum of 250 preset positions can be (optical x12 zoom, digital x16 zoom) programmed.
2) INSTALLATION AND CONNECTION 2-1.
2-2. INSTALLATION Indoor Make 4 holes after attaching ceiling guide where the camera is set. Set up DIP switch (Reference to XXP) Tighten 4 screws. Take out the cables from the ceiling. Take apart 4 bands of camera body cover Connect with cables.
Outdoor Unscrew the 4 bolts of the bubble cover then separate the camera housing. Connect the power, data, and video cables at Recombine Connect Cover, then set DIP SWITCH. (Go to and attach the bracket.
2-3.
Outdoor
3. DIRECTIONS FOR USE 1) DIP SWITCH SETTING Outdoor Indoor Set the camera numbers in the state of ADDR, set communication speed, protocol in the state of INIT. -This part is each address of It shows the status of Power On/Off. Green LED is On while power is alive. In the status of operation, red LED is off. camera.- -TERMINALATION RESISTOR (DIP S2/SW1) ~Turn the last camera on the data line as a switch to turn on/off the terminal resistor on.
2) HOW TO CHANGE PROTOCOL Set up this part. The switch that selects Protocol. The switch that selects Baud Rate. . Change No.3 at S2 to INIT if want to change Protocol. ① ② ③ ④ ⑤ Please make Power off. Switch Protocol that wants to change on as above table. Make Power on, then set Protocol and Baud rate are appealed. Make Power off, if every setting is right. Then it is done. Change No.3 of S2 to ADDR before Power on, then make Power on after setting the address of the camera.
3) HOW TO SET ADDRESS DIP SWITCHES Use DIP switches No.1 to No.8 for address, it can be set 1 program to 255 program.
4) HOW TO USE OSD MENU 4-1. HOW TO CONTROL OSD MENU OSD (ON SCREEN DISPLAY) CONTROL It is the function to call up the Menu ＊User can not only set Preset, Group, Tour, Swing, Trace functions of the camera up by the menu, but also set them up by shortening keys. (Refer to 4-3 content) ACCESSING OSD MENU ① ② ● The menu is displayed on the screen with the key tone when user presses No.1 and menu key. ◄◄ CAMERA SETUP p1 ►► 1. ID Set : CAM-001 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4.
4-1. FUNCTIONAL DESCRIPTIONS ON EACH MENU 1. ID SET. ◄◄ CAMERA SETUP p1 ►► 1. ID Set : Press F/F Key 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Medium 5. Shutter speed. : AUTO 6. Sharpness level : 06 7. Brightness : 09 8. Flickerless : OFF 9. DNR Control : Medium - NEXT MENU PAGE This function is to set camera ID up to 16 letters on the monitor.
◄◄ CAMERA SETUP p1 ►► 1. ID Set : Press F/F Key 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Medium 5. Shutter speed. : AUTO 6. Sharpness level : 06 7. Brightness : 09 8. Flickerless : OFF 9. DNR Control : Medium - NEXT MENU PAGE 4. AGC CONTROL AGC(Automatic Gain Control)- It adjusts the amount of video amplification to maintain a full 1volt peak-to-peak video signal output automatically. ▶ Low, Medium, Max 5. SHUTTER SPEED ◄◄ CAMERA SETUP p1 ►► 1. ID Set : Press F/F Key 2.
◄◄ CAMERA SETUP p1 ►► 1. ID Set : Press F/F Key 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Medium 5. Shutter speed. : AUTO 6. Sharpness level : 06 7. Brightness : 09 8. Flickerless : OFF 9. DNR Control : Medium - NEXT MENU PAGE ◄◄ CAMERA SETUP p1 ►► 1. ID Set : Press F/F Key 2. OSD Display. : ID + Status 3. H-V Reverse. : Normal 4. AGC Control : Medium 5. Shutter speed. : AUTO 6. Sharpness level : 06 7. Brightness : 09 8. Flickerless : OFF 9.
◄◄ CAMERA SETUP p2 ►► 10. Back Light : WDR Mode 11. Set Back Light Mode 12. White Balance : Auto 13. Focus Mode :Oneshot 14. Zoom Max Limit : Off 15. DSS Control : 10 Field 16. Day&Night : Auto+Low 17. Stabilize On/Off : Off - PREV MENU PAGE - NEXT MENU PAGE 11. SET BACK LIGHT MODE ▶ WDR MODE - Limit: Adjust the WDR Sensitivity by selecting Low or Max - Level: Adjust the WDR Brightness by controlling 0~15.
◄◄ CAMERA SETUP p2 ►► 10. Back Light : WDR Mode 11. Set Back Light Mode 12. White Balance : Auto 13. Focus Mode :Oneshot 14. Zoom Max Limit : Off 15. DSS Control : 10 Field 16. Day&Night : Auto+Low 17. Stabilize On/Off : Off - PREV MENU PAGE - NEXT MENU PAGE ◄◄ CAMERA SETUP p2 ►► 10. Back Light : WDR Mode 11. Set Back Light Mode 12. White Balance : Auto 13. Focus Mode :Oneshot 14. Zoom Max Limit : Off 15. DSS Control : 10 Field 16. Day&Night : Auto+Low 17.
◄◄ CAMERA SETUP p3 ►► 18. Select Alarm : Sensor 19. Motion Detection : Off 20. Preset Set & Run Page 21.Trace Set Page 22. Alarm CH On/Off Page 23. Alarm Preset Set Page 24. Privacy Zone Set Page - PREV MENU PAGE - NEXT MENU PAGE ◄◄ CAMERA SETUP p3 ►► 18. Select Alarm : Sensor 19. Motion Detection : Off 20. Preset Set & Run Page 21.Trace Set Page 22. Alarm CH On/Off Page 23. Alarm Preset Set Page 24. Privacy Zone Set Page - PREV MENU PAGE - NEXT MENU PAGE 18. SELECT ALARM Set alarm mode you want to use.
② Preset PTZ set : Set the position of Preset Select the main menu with the joystick, then press F/F key for next page. Select [SAVE] with F/N key after setting the Preset point by using the joystick and. In/Out function, then the data is saved if user presses F/F key, then it is moved to the previous screen automatically from the menu ※ Repeat the same way after changing the number of Preset, if user set another Preset .•[SAVE]: Previous screen. [DELETE]: Remove.
③ Preset Swing SET : Set Preset Swing Move next SWING page for the setting, if user presses F/F key in the state of selection of the menu ※The preset must be set before the setting as Swing Is a function to repeat an auto observation of 2 Preset points user fixes in Preset set ④ GROUP SET: User can set maximum 12 groups. Select a channel then move to next page after pressing F/F key ※The Preset point in the Group that 12 Preset points are set is observed repeatedly and order with regular speed and time.
⑤ Tour SET Group: User can set continual Group motion that can be put 12 Groups in 1 Tour Move to the setting page if user presses F/F key on this menu ■ The Group user wants to set must be set firstly ※Setting is only possible when Preset is set first in the state of setting of Swing, Group, Tour, otherwise, it displays the message “Sorry Undefined”. ⑥ Run Function: Operate one of SWING/ ＊Set / Stop order with a control keyboard without menu GROUP / TOUR / TRACE. (It is operated on the screen.
If user saves new positions without “DELETE”, all saved positions will be deleted automatically. 22. ALRAM CHANNEL ON/OFF ◄◄ CAMERA SETUP p3 ►► 18. Select Alarm : Sensor 19. Motion Detection : Off 20. Preset Set & Run Page 21.Trace Set Page 22. Alarm CH On/Off Page 23. Alarm Preset Set Page 24. Privacy Zone Set Page - PREV MENU PAGE - NEXT MENU PAGE - CH On/Off : Alarm Input – Each channel can be ON/OFF - Alarm Relay : It can be set On or not when ALARM OUTOUT PORT operate wrong.
■ Home Position Preset The camera automatically moves to where master user set, when another user controls the camera to observe other area. (You can set 1~250 points) ■ Home Position Time It sets the dwell time in Home Position Preset. It automatically moves to where observes ordinarily in the regular time that Master user set in observation of other area, if set Home Position Preset. (You can set 1~180sec. Set control Home Position Preset and Home Position Time together for using this function.
◄◄ CAMERA SETUP p4►► 25. Auto Tilt Mode : Off 26. Smart Pan/tilt : ON 27. Manual P/T Speed : Medium 28. Auto Refresh Time :1day 29. Shortcut Key : On 30. Use Password :Off 31. Language :English 32. Factory Reset Warning - PREV MENU PAGE ◄◄ CAMERA SETUP p4►► 25. Auto Tilt Mode : Off 26. Smart Pan/tilt : ON 27. Manual P/T Speed : Medium 28. Auto Refresh Time :1day 29. Shortcut Key : On 30. Use Password :Off 31. Language :English 32. Factory Reset Warning - PREV MENU PAGE ◄◄ CAMERA SETUP p4►► 25.
◄◄ CAMERA SETUP p4►► 25. Auto Tilt Mode : Off 26. Smart Pan/tilt : ON 27. Manual P/T Speed : Medium 28. Auto Refresh Time :1day 29. Shortcut Key : On 30. Use Password :Off 31. Language :English 32. Factory Reset Warning - PREV MENU PAGE 29. SHORTCUT KEY The Shortcut Key can make some of the functions to perform faster and easily.
◄◄ CAMERA SETUP p4►► 25. Auto Tilt Mode : Off 26. Smart Pan/tilt : ON 27. Manual P/T Speed : Medium 28. Auto Refresh Time :1day 29. Shortcut Key : On 30. Use Password :Off 31. Language :English 32. Factory Reset Warning - PREV MENU PAGE 32. FACTORY RESET WARNING Please be careful of that all setting data of OSD MENU are reset into the first default when operates FACTORY RESET WARNING.
4-3. SETTING FUNCTIONS BY KEYBOARD 1. Preset setting User can set Preset point up to 250. ① Preset Input Preset setting can be set 1 to 250 sequentially after moves the camera to the place to will be memorized ② Preset Move Move to the fixed point if user presses P-SET button after pressing Preset number that user wants. ③ Delete a separate Preset Ex) Delete 5th Preset Go on in order as follow when the sound is heard in 3 sec after pressing (waiting for 3 sec) .
3. Group setting ① Start Group setting mode Set Preset No. again in continual input. Set a GROUP again from the first after ending with , if user wants to finish Preset input in one Group to input another Group.
4. Tour set mode ① Tour set mode ② Start / End Tour ③ Delete Tour 5. Spiral Function It is a function to observe objects automatically in the spiral direction. ① Spiral On ② Off * 26.
6. PTZ Trace It memorizes P/T/Z motions for 200sec then operates them at the same Trace. ① Start / End Trace ② Off ② Set Trace ③ Delete Trace * 26.
4-4. OSD MESSAGE DESCRIPTION 1. PRESET MESSAGE It is CAMERA ID and it can be changed in ID SET MODE. CAM-001 Set PST 001 PRESET 001 User can check that Preset No.1 is saved as an appeared message in Preset set 2. SWING MESSAGE CAM-001 [SWING] PRESET:001 It shows that is RUN SWING mode in SWING Run. CAM-001 CAM-001 It appears when moving to the preset No.1 Clear PST 001 It appears when user deletes PRESET No.1. The message ‘All clear PRESET’ is displayed when user delete PRESER data all at once.
3. GROUP MESSAGE CAM-001 GP:01 P002,T001,S64 As the message in the time of operation of GROUP SET, “GP:01” means group No.1, “P002” means PRESET No.2, “T001” means waiting time is 1sec and “S64” means move speed is 64 CAM-001 CAM-001 [GROUP: 01] Save Group 01 As the message in the time of completion of GROUP SET, it is displayed. GROUP No.1 was saved. . PRESET:001 It is displayed in the time of operation of GROUP RUN, it shows GROUP No.1 will move to No.1 4.
4. TROUBLE SHOOTING CAUTION IN USE • Make sure that turn the power switch off before installation. • Avoid the places where is the high/low temperature and humid. • Power supply must be min AC24V/1A for indoor (DMS-200) and min AC24V/1.5A for oudoor (DMS-200Se) • Please be careful of that you connect respective wires without mismatching in installation.
5. ASSEMBLES measurement Indoor Wall Mount Bracket It can be connected with D-max bracket by using mount. (The mount and bracket are optional for indoor, DMS-200) unit : mm ① Connect MOUNT with Wall bracket ② Fix 4 screws. ④ Completion ③ Connect Camera body cover.
Outdoor Wall Mount Bracket ③ Connect the power, data, and video cables at Connect Cover ① Unscrew the 4 bolts of the bubble cover then separate the camera housing. ② -1. Fix four bolts after connecting each line and block up the side hole of the bracket with 34mm block rubber. ④ Recombine the housing and body then attach the bracket. ② -2. Connect the lines as above the picture when setting on the concrete structure such as retaining wall. Then connect TAB/P1/11” flexible connector (28Ø).
6.
▪ SETTING ONE KEYBOARD : Control line : Video line
7. SPECIFICATION MODEL Signal system Image sensor Effective pixels DMS-200 NTSC PAL 410K Pixel, 1/4 " SONY Super HAD CCD 768(H) X 494(V), 752(H) X 582(V), Horizontal resolution More than 600 TVL B/W 700 TVL Lens 10x Optical zoom, f=3.94 – 46.05mm, F1.67~1.88 Digital zoom 12x (Total zoom 192x) Angle of view H: 51.54° (Wide) x 4.49° (Tele), V: 39.28° (Wide) x 3.39°(Tele) Minimum illumination 0.
