HIGH SPEED DOME CAMERA USER MANUAL DSC-300Si5/Se5
Table of contents 1. CAUTION -------------------------------------------------------------------------------- 2 2. INTRODUCTION OF PRODUCT 4 1). DESCRIPTION AND FEATURES --------------------------------------------- 4 2). INSTALLATION AND CONNECTION ---------------------------------------- 5 3. 2-1. NAME AND FUNCTION OF EACH PART ----------------------------- 5 2-2. INSTALLATION -------------------------------------------------------------- 6 2-3.
1.CAUTION Thank you for purchasing our product. Please operate the product after being fully aware of the manual. Pease contact us if you have any queries. Precaution Note the following matters before the installation of the product. Avoid the following places for the installation. A high/low temperature: Using indoor-cameras Snow, rain and wet: Humidity or water and in the places of +50°C~ -10°C can cause any liquid inside-camera can cause troubles. troubles and lower its capacity.
Caution in Use Do not disassemble the unit and put alien substances in the unit. - Disassembling the unit or putting alien substances such as a metal can make the camera defective. - Make sure of power switch-off before the installation. : Ensure power switch-off and check the voltage the camera before the installation. - Do not give the unit a shock and an operation. : Giving a strong shock or an excessive power on the button, terminal can cause problem.
2. INTRODUCTION OF PRODUCT 1) DESCRIPTION AND FEATURES This camera has been designed elegantly for buildings, department stores that need to be in harmony with the interior as a high speed dome camera, including various observation functions.
2) INSTALLATION AND CONNECTION 2-1.
2-2. Installation INDOOR TYPE OUTDOOR TYPE SEPARATION OF LOWER COVER Loosen the bolt of the back of lower cover by Loosen the four bolts of the lower cover, then a screwdriver(+), then turn the cover as separate. above the picture and pull the lower cover to the down SEPARATION OF UPPER COVER Loosen the three bolts, the round head shaped, of the camera body. The three bolts are not loosened completely and not come up more than 1cm of the lower cover, then separate.
Pull the cover up with grabbing the bottom of the camera after loosening the three bolts Open the connector cover, then connect power, data, video cable and sensor The cover is opened if user loosens the one bolt on the connector cover by using a screwdriver(+). The bolts not loosened completely to protect from missing of them.
Have you connect the power cable in the right direction ? If yes ① RED led, in the niddle of the connector, is lighted ② Use AC24V power souce and user can use any power input that is connected with a terminal and a jack(But use 1 input).
2-3. Connection diagram DC12V/1A adaptor and junction box are provided on Connect the image line of a a purchase, Junction box consists of 2 data ports monitor ( Each data port can be connected with maximum up to 128 cameras and sub keyboard terminal. Reference to the following page. User can control maximum up to 255 cameras connected by using the exclusive control keyboard. User can connect it maximum up to 1.
Must use AC24V power source, current intensity must be less than 1.5A and must use a double winding transformer Alarm output is tangency output of relay non-load, it can be used up to AC220/10A by connecting the load.
3. DIRECIONS FOR USE 1). DIP SWITCH SETTING Ser the camera numbers in the state of It is a notice to turn the data signal ADDR. on.(in power on, the green led is Set communication speed. Protocol in the state od INIT. turned on - This part is each address od camera Set the power of the camera switch-off to control the dip switch and set switch-on after using it.
2) HOW TO SET PROTOCOL Set this part up Do not necessary to set it up O 4 I P I N 2 N A N 2 I L T ADDRESS O ON T . F F O N OFF 1 2 3 4 5 6 7 T 4 A N E M 8 D T X S2 5 D S T R C .
3) SETTING ADDRESS OF DIP SWITCHES. Use DIP switches No.1 to No.8 for address, it can be set 1 program to 255 program.
4) HOW TO USE OSD MENU 4-1. How to control OSD menu ● OSD (ON SCREEN DISPLAY) CONTROL It is the function to call up the Menu ＊User can not only set Preset, Group, Tour, Swing, Trace functions of the camera up by the menu, but also set them up by shortening keys. (Refer to 3-3 content) ● Accessing OSD MENU (1) The menu is displayed on the screen with the key tone when user presses No.1 and menu key. ● OSD Menu Control. << CAMERA SETUP p1 >> 1. ID Set : 2.
4-2. Functional Descriptions of each Menu. 1. ID SET. It is the function to set ID of the camera. Move to No.1 menu and the screen moves as following when user presses F/F key. User can choose letters that they want, if user control a joystick up / down / right / left, and user can reselect the previous letters, if user presses Z/I, Z/O or turn the head of the joystick to right/left.
<< CAMERA SETUP p1 >> 1. ID Set : CAM-001 2. OSD Display : ON 4. SHUTTER SPEED Shutter speed is the duration of the electronic shutter. Set shutter speed to operate automatically (Auto) or manually (Numeric Value). 3. Back Light : OFF ●AUTO (default) – The electronic shutter speed is set automatically by 4. Shutter speed : AUTO the amount of light sensed by the camera. 5. BLC level : 052 ●Manual – it allows to control iris with this menu. Before setup, please 6.
9. ZOOM MAX LIMIT << CAMERA SETUP p2 >> Zoom max limit allows the user to define a limitation on the amount of telephoto zoom. The default setting is X46. 9. Zoom MAX Limit : x70 10. DSS Control : 16 fields 11. WDR On off : 12. WDR Level : 100 13. DAY&NIGHT of/off : AUTO-LOW Off 14. PRESET SET & RUN PAGE 15. TRACE SET PAGE - NEXT MENU PAGE Camera with 420X zoom (35X optical zoom and 12X digital zoom) can be set for X35, X70, X105 …….. and X420. 10.
according to low light condition with medium sensing. << CAMERA SETUP p2 >> ●AUTO-LOW: Convert to monochrome mode automatically according to low light condition with low sensing. 9. Zoom MAX Limit : x70 10. DSS Control : 16 fields 11. WDR On off : 12. WDR Level : 100 13. DAY&NIGHT of/of f: AUTO-LOW Off ● AUTO-HI: Convert to monochrome mode automatically according to low light condition with high sensing ● OFF: Do not convert to monochrome mode, even if the camera in low light condition.
F/F key, then it is moved to the previous screen automatically from the menu. • [SAVE]: Previous screen. [DELETE]: Remove. [ESC]: Cancel ＊Repeat the same way after changing the number of Preset, if user set another Preset. ③ Preset Swing SET: Set Preset Swing, • P/T Swing: TILT-Observe up and down, It moves to next SWING page for the setting. If F/F key is pressed in selection PAN-Observe right and left • Start Preset: Preset number of the location that of the menu the observation is started.
④GROUP SET: User can set maximum 12 groups • [P]: Set Preset (1~250) Select a channel then move to next page after • [S]: Move speed (1~64) pressing F/F key • [T]: Dwell time ■Set 12 Preset points in one Group, it is a function that observes the Preset points in the Group repeatedly and in order with regular speed, time order with regular speed and time 1. Set Preset 2. Next setting 4. Next setting 5. Delay time 3. Set move speed 6. Out of menu after saving data 1. Select Group channel 2.
■ You can look at how to set TRACE at “18. TRACE SET PAGE” ⑦ RETURN MENU PAGE: Move to a higher menu page if select this menu, then control the joystick Right/Left << CAMERA SETUP p2 >> 15. TRACE SET PAGE 9. Zoom MAX Limit : x70 Set TRACE. 10. DSS Control : 16 fields You can control the camera Zoom In / Out anywhere by 11. WDR On off : a joystick and can memorize or play it 12. WDR Level : 100 13. DAY&NIGHT of/off : AUTO-LOW Off 14.
■ How to set TRACE Move to [SET] after pressing „ F/N KEY ‟ F/F KEY Check – Control the scenes that you want to save a joystick after the message “Set Trace: OO%” on the middle of the screen. If you are done with above action, move to [SAVE] with „ F/N Key „ It goes to a higher menu after saving the data with the message “Save TRACE”, if ‟ F/F KEY is pressed. 16. ALRAM CHANNEL ON/OFF << CAMERA SETUP p3 >> ■ What is the ALARM function? : It uses a sensor and 16.
17. ALARM PRESET SET PAGE << CAMERA SETUP p3 >> 16. ALARM CH ON/OFF PAGE 17. ALARM PRESET SET PAGE 18. Select Alarm : Sensor 19. Motion on/off : Off 20. Motion Detection Set : ■ The camera moves to a preset point automatically when Alarm activates in each ALARM CHANNEL. ■ Set preset points to move to and give a Preset number to each ALARM CHANNEL. ■ If ALARM CHANNEL No. is „0‟, the unit doesn‟t move to Preset position. 21. PRIVACY ZONE SET : ■ You can select PRESET number from 1 to 250.
20. MOTION DETECTION SET << CAMERA SETUP p3 >> Detect Level: 00 ~ 05 (High number is high sensing) 16. ALARM CH ON/OFF PAGE Detect Position: 01 ~ 08 (Set up to 8 zones) 17. ALARM PRESET SET PAGE 18. Select Alarm : Sensor 19. Motion on/off : (To set this function, „Select Alarm‟ should be set „Motion‟ and the video will be fixed in this function) Off 20. Motion Detection Set : 21. PRIVACY ZONE SET : . - NEXT PAGE - Set up the parameter of detection position 01 to 08.
③ Confirm, Next page ④ Fix the black square on the middle of area that you want to hide by a joystick, then go back to the previous page by [F/F] key after controlling the size of the square by [Z/I], [Z/O] key and saving it. Set the position BOX Extension / Reduction Check ⑤ The Channel is changed BLANK to „OFF‟. The screen displays the black square, if you change the CH „ON‟ as the left picture. Move to the Channel Change the CH „ON‟ Check ⑥Out of OSD MENU << CAMERA SETUP p4 >> : On 24.
<< CAMERA SETUP p4 >> 24. MANUAL P/T SPEED You can control the maximum speed when controlling up and 22. Auto Tilt Mode : OFF down. It consists of Low, Medium, Max and one turn (360°)/sec 23. Smart Pan/tilt is possible in Max. : On 24. Manual P/T Speed : Medium 25. Language: English 25. LANGUAGE 26. FACTORY RESET! WARNING! English, Portuguese, Polish - PREV MENU PAGE 26.
4-3. Functional Setting, Operating/Deletion by the Keyboard 1. Preset setting You can set Preset point up to 250. ① Preset Input. Preset setting can be set 1 to 250 sequentially after moves the camera to where you want ② Preset Move The camera moves to the preset point, if you press Preset No.
② Operation of Swing (Run Pan) ③ End of Swing (Run Tilt) 3. Group setting ① Start Group setting mode Start the Group Select the Group in 1~12 Select in Preset No.1~250 setting mode and input them. Move Speed: The Speed from A to B 64=High, 1=Low Dwell Time: The dwell time at the point of A or B before the move. (sec) - Set Preset No. again if you want to input it continuously.
EX). Register Group No. 1,3,6 as Tour Start Register Register Register Finish Tour mode Tour No.1 Tour No.2 Tour No.3 Tour mode ② Start / End Tour Start Tour ③ Delete Tour Finish Tour 5. Spiral Function It is a function to observe objects in the spiral direction. ① Spiral observation „ON‟ ② End 6. PTZ Trace It memorizes P/T/Z motions for 200sec, then operates them at the same Trace.
4-4. OSD MESSAGE DISCRIPTION 1. PRESET MESSAGE CAM-001 SET PST 001 User can PRESET 001 check that preset No.1 is saved as an appeared CAM-001 message It is CAM-001 CLEAR PST 001 displayed when moving to the preset No.1 in It is displayed when user deletes preset No.1.
CAM-001 CAM-001 CAM-001 TOUR&GP:01 PRESET:001 CLEAR TOUR & GRP As the message in the time As the message in the It shows the data in group of operation of Tour set, time of operation of tour anf tour saved was deleted. “GP:01” means group No.1 run, and it shows that group No.1 moving to preset No.1 in was saved. group No.1 SET TOUR GP:01 it will show that CAM-001 RUN SPIRAL RUN SPIRAL : It is the message in the time of operation of spiral sequence.
4. TROUBLE SHOOTING 1. You must turn off the power switch before installation of this equipment 2. Avoid installation places where it is the ultimate cold, hot, and humid. 3. Use a power supply of AC24V, 1.5A output. 4. Please be careful that you connect respective wires without mismatching in installation. 5. Check the controlled cable‟s insulation connecting to exterior and supply to power sources. 6.
exactly presser position or different. mode? preset in the set mode. When it activate alarm state, there is Did you use the exclusive control It is need to use an exclusive control no sign on the keyboard controller keyboard? keyboard so that the alarm sound is activated on the controller Yes, I do. Please select on to enable alarm of the related camera.
5.
In-ceiling mount bracket 35
6. ASSEMBLY DSC-30EWP Wall mount bracket ① Remove main the body of camera from the housing ③ Fix the upper cover into a wall bracket with turning it in the same direction as the picture ④ Connect the data cable, video ② Fix four bolts after connecting each line cable and power source cable. and block up the hole of the bracket‟s body with 34mm block rubber.
DSC-20ECP Wall mount bracket 17.2 Assembly of outdoor dome with pole mount pendant 1 3 Remove the Main body of Turn the ceiling The camera pole to connect. From the Housing. Fix the pole 2 box on 4 the ceiling. Turn the joint coupler 5 Turn the cover coupler connect. 6 7 Connect the cover coupler with the Connect the data lines. housing and fix it Connect the video lines. with 3-bolts. Connect the power. 9 8 Rejoin the main body of the camera to the housing.
Sub keyboard Sub keyboard 38
Set one main keyboard 39
7. SPECIFICATION MODEL Signal system INDOOR NTSC PAL 1/4” Sony Ex-View CCD Image sensor Effective pixels 768(H) X 494(V), 752(H) X 582(V), Horizontal resolution More than 520 TVL Lens 35x Optical zoom, f =3.4 –119mm Digital zoom 12x (Total zoom 420x) Angle of view Approx 55.8° (Wide), Approx 1.7° (Tele), Minimum illumination 0.1Lux, MAX: 0.
MODEL Signal system OUTDOOR NTSC PAL 1/4” Sony Ex-View CCD Image sensor Effective pixels 768(H) X 494(V), 752(H) X 582(V), Horizontal resolution More than 520 TVL, B/W 570 TVL Lens 35x Optical zoom, f =3.4 –119mm Digital zoom 12x (Total zoom 420x) Angle of view Approx 55.8° (Wide), Approx 1.7° (Tele), Minimum illumination 0.1Lux, MAX: 0.
