TABLE OF CONTENTS • Introduction..........................................3 • Product Overview ................................3 • Features ................................................4 • Package Contents .................................4 • BTB 800 Parts & Functions .................4 • BTB 800 Operation..............................5 • BTB 809 Parts & Functions .................6 • BTB 809 Operation..............................6 • Recharging the Collar Battery .............
INTRODUCTION Thank you for choosing a D.T. Systems Beeper Collar! The BTB 800 and BTB 809 give you the ability to keep track of your dog’s location when he is out of sight and lets you know when he has gone on point. This allows you to find the dog quickly and prevents you from making the mistake of calling the dog to you when he’s on point. The BTB 800 and BTB 809 beeper collars are light weight and built to withstand the rugged conditions and heavy cover dogs often encounter.
FEATURES • • • • • • Easy Operation - One touch push button system. Long Range Audibility - Audio booster element. Reliability - State-of-the-art microcomputer technology. Two Operating Modes - Run/Point, or Point only. Rechargeable Batteries - Charger included. Remote Control Activation - (BTB 809 only) 250 yard range.
BTB 800 OPERATION Turning the unit ON: To turn the BTB 800 ON, depress the Power and Mode Selector Switch for approximately two seconds. (When you press the switch the LED indicator will light for two seconds. As soon as the light goes out you may let go of the switch). The unit is now ON. The LED light will blink once every two seconds. Turning the unit OFF: Turning the BTB 800 OFF works the same way as turning it on, depress the Power and Mode Selector Switch for approximately two seconds.
BTB 809 PARTS & FUNCTIONS BTB 809 OPERATION Turning the unit ON: To turn the BTB 809 ON, depress the Power and Mode Selector Switch for approximately two seconds. (When you press the switch the LED indicator will light for two seconds. As soon as the light goes out you may let go of the switch). The unit is now ON. The LED light will blink once every two seconds. Turning the unit OFF: Turning the BTB 809 OFF works the same way as turning it on, depress the Power Switch for approximately two seconds.
The BTB 809 has Two Operating Modes. Run/Point and Point only. When the unit is first turned on it is automatically set to Run/Point mode. To switch to Point only mode quickly depress the Power and Mode Selector Switch (less than one second). The LED indicator light will blink once and then resume blinking once every two seconds.
CHANGING THE REMOTE BATTERY (BTB 809) 1. Unscrew the small screw on the back of the Remote Control unit. 2. Replace both 3 Volt watch style batteries as shown below. Note: Watch “+” “-” while installing. If battery is installed backward it may cause the unit to operate in Vibration mode only. TROUBLESHOOTING Q & A 1. 2. 3. Q : My Collar’s range is not as far as when I first bought the unit. A : (a) Test batteries. They may be low. (b) Fully extend transmitter antenna.
TROUBLESHOOTING Q & A CONT. 4. Q : My Transmitter LED lights when any button on the transmitter is pushed, and the collar LED is blinking (indicating the unit is ON), but the unit is not working. A: The transmitter and collar frequencies are not in synch. Try the following procedure to restore... 1. Turn the collar ON by depressing and holding the Power and Mode Selector Switch for approximately two seconds. DO NOT STOP PRESSING THE SWITCH. 2.
GETTING YOUR DOG ACCUSTOMED TO THE SOUND • Turn on the collar and leave it outside the dog’s kennel area for about a half an hour. Make sure you leave the mode set at Run/Point and do not change the mode to Point only. • Repeat this several times, until you can see that the dog is disregarding the beeper. • Next, fill the Speaker Horn with tissue paper and fit the beeper collar on the dog. Let him run around a little while.
WARRANTY All BTB beeper collars have a One Year Parts and Labor Warranty, effective from the original date of purchase. (A copy of the original sales receipt is required to validate the date of purchase). NOTE BTB 809 Remote Control batteries are replaceable/ disposable and are not covered under the warranty. Damage by user, abuse or loss of parts, and attempted repair damage by the user or his agent are not covered by warranty.
D.T. Systems, Inc. 2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) LUV-U-DOG Fax: (214) 350-7847 Website: http://www.dtsystems.com E-mail: customerservice@dtsystems.