H20Series Electronic Dog Trainer Owner's Manual H20 1810 Series H20 1820 Series H 2 01830 Series H20 1850 Series LJm D.b Systems, Inc.
r NOTICE! 3 According to how you uw your transmitterr, the transmitting range might be much difkrent.
TABLE OF CONTENTS Table of Contents .................................. 3 Introduction............................................ 4 Package Contents ................................. 5 Model Features...................................... 6 Adjusting and Positioning Your Collar for Proper Fit....................... 7 Parts and Functions............................... 8 Batteries ................................................ 13 Setting Intensity Levels.......................... 14 ProgrammingITesting......
Congratulations and thank you for purchasing our HzOSeries TM Training Collar. The H20series represents the absolute latest technological advancement in the Electronic Dog Training World. It offers Maxx-RangeTM,the industry's only internally woven antenna in the collar. With up to a one mile range, they are perfect for hunting, basic obedience and professional training. H20series collars feature Sixteen levels of stimulation intensity, with an easy 'no-look' clicking intensity selection dial.
IMPORTANT NOTE: Please read this owner's manual in its entirety before operating this unit. Should you have any questions about our collars or their operation please contact our Customer Service department (see back page for address and phone number information).
0Series Digital Technology One mile range trainer Lightweight, waterproof collar and transmitter 16 adjustable intensity levels of Momentary ('Nick') Stimulation, and Constant Stimulation Rechargeable Ni-MH battery system Gentle Touch SystemTMExtra Mild Stimulation MAXX-RangeTMInvisible, Embedded Collar Antenna Built in safety shut-off system All models available in two and three dog systems Positive Vibration (H20 1820,1822, & 1823 only) NEW Jump feature allows you to instantly "jump" to a predetermined i
AUJUP I ANU QL r u a I~ AUNANU TUUK COLLAR FOR PROPER FIT Proper collar tightness and position are very important to insure safety and correct functioning every time you use the collar. All electronic collars need to be very snug to work properly. They must be just tight enough to allow the "prongs" or electrodes to make good skin contact. If your collar is too loose, the stimulation may not work properly because good skin contact is not being achieved.
Indicator Light Intensity Dial Momentaw 'Nick' stimulaiion # (Function I varies accordi to model) #2 (Function varies according to model) Continuous Stimulation Multi-Unit Selection Switch \ Charging Battery Transmitter (Multiple dog transmitter shown)
Collar Belt with Embedded Antenna \Beeper Horn Collar Receiver Turnina the Unit On: Press and hold the OnIOff button on the Collar Receiver. The Red LED Indicator will light solidly for two seconds. Continue holding the Button until the Red light goes off. The unit is now On. The LED lndicator will now flash approximately every two seconds. (Note: The Transmitter is always in a permanent sleep state.
Intensity Selection Dial The intensity selection dial allows you to choose between sixteen different levels of stimulation, allowing for very precise control. Transmitter Indicator Linht When orle of the push button switches on the transmitter is pushed, the RED light will turn on to indicate that the transmitter is being operated, When the battery needs charging the RED light will blink once every 112 second while holding the continuous stimulation button.
I PARTS & FUNCTIONS CONT. Vibration Buttons (H20 18201182211823) Pressing the button on the left (#I) of the transmitter causes the collar to vibrate. Pressing the button to the right (#2) of the transmitter causes the collar to vibrate for 112 second. After 112 second, continuous stimulation will be applied simultaneously with the Positive Vibration. Jump Button lH2018301183211833) Pressing the button on the left (#I) of the transmitter causes the collar to administer a 'Jump' Stimulation.
Battery Charging Receptacles The battery charging receptacle is located on the side of the Transmitter, and on the side of the Collar Receiver facing the dog's neck. After charging, always close the jack with the rubber plug to prevent foreign particles from getting inside the unit. Collar Indicator Light When the Collar Receiver is turned on, the RED light will flash steadily once every two seconds to indicate that the unit is active.
I All H20 Series TM collars are equipped with rechargeable Nickel Metal Hydride (NiMH) batteries. NiMH batteries are not memory sensitive and do not require depletion before recharging. The batteries come partially charged from the factory. However, it is recommended that you give the battery a full charge (about 12 hours) before the first use. Remember - Always keep batteries away from flammable substances (especially when charging).
The first and most important step in training your dog with your H20Training System is determining the correct lntensity Level to provide the proper training stimulation without over-shocking your dog. To do this place the Collar on the dog's neck and turn it on. Place the lntensity Selection dial so that the System is set on Level One. Press either the 'NICK' or the 'CONT' Button. Increase the lntensity Level in increments of one until the dog is feeling the stimulation.
Settincl the Jump Stimulation Level: (H20 18301183211833 only) 1. Set the intensity level to the level that you would like it to "jump" to 2. On the transmitter, press and hold buttons #I and #2 ('Jump' and 'Rise' buttons) at the same time. 3. When you see the LED flashing, release both buttons. The number of times the LED light flashes shows you the intensity level for the Jump Stimulation. 4.
Press and hold the power button on the Collar Receiver. You will see the LED light on the collar blink 7 times before staying solid. You must hold down the power button until the LED light becomes solid. Simultaneously, press and release the nick and continuous buttons. In a few seconds, you will see the LED light blink 3 times. The collar ID is now programmed, and the collar receiver is now ON. Before testing, make sure that both units are fully charged and the power to the Collar Receiver is "ON".
To Test the Vibration: (H20 18201182211823 only) A) Follow the directions for testing the Electronic Stimulation, and press the button on the left side of the transmitter. B) If you press the button on the right side of the transmitter, the unit should vibrate for 112 second and then the tester should light while vibrating at the same time. To Test the Beeper: (H20 18501185211853 only) A) Press the button located on the left side of the transmitter (Locate button).
Before beginning training, your dog should be examined by a veterinarian to assure that your dog is in good health. Never leave your don unattended with the unit on. -Since no electronic device is perfect, there is a very slight possibility that your dog may receive an unintentional electric stimulation. Your H20Series TM training collar is a very valuable tool if used correctly.
It is ve important to periodically clean your H20 Seriesy"' systems for maximum performance. Regular cleaning will also lengthen the life of your unit. Clean the H20 Series TM collar box with lukewarm water and a mild anti-bacterial soap. Take care to thoroughly clean the space between the electrodes and the belt. The belt and buckle should be cleaned with water and a mild soap then allowed to dry completely. Always allow the entire unit to completely dry before using.
-- D.T. Systems Premium Lifetime Warranty is the best warranty offered in the industry. This warranty is free to participating U.S. customers. (The warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor warranty to a limited lifetime warranty against manufacturing defects on parts and a one year warranty on labor. What is covered: D.T.
VAKKAN I T LUN I How the Limited Lifetime Warrantv works: To qualify for the Warranty you must fill out the warranty registration card which came with your system and mail it (with your original sales receipt) to D.T. Systems within 30 days of purchase. There is no charge for parts or labor for the first year on any of our lifetime warranty products.
I FCC COMPLIANCE I Your H20 Series has been manufactured under complete compliance with the Federal Communication Commission (FCC). The complex internal structure of each product has been designed to operate within specific regulations of FCC specifications. Any unauthorized modifications to your product is a violation of these specifications. The H20 Series TM has been made with State of the Art equipment. Any fine adjustment should be performed only by D.T. Systems' technicians.
% 0.T. systems, Inc. 2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) LUV-U-DOG Fax: (214) 350-7847 Website: http://www.dtsystems.com E-mail: customerservice@dtsystems.
