FS-L4202D ( 42" ) MEDIC AL LCD MONITOR USER'S GUIDE
Table of Contents Symbol Definitions 2 Safety Instructions 4 Caution 7 FCC Information 10 Parts 15 Connector 16 Mechanical Product Drawing 17 Control 18 Power mangement 21 Adjust OSD Menu 22 Stansard Signal table 25 Signal connector Pin Assignments 26 Specification 29 English - 1
Symbol Definitions The following symbols appear on the product. its labeling, or the product packing. Each symbol carries a special definition, as defined below Dangerous : High Voltage. Consult accompanying documents. Maximum Stacking. Indicats proof of conformity to applicable European Econmic Community Council directives and to harmonzed standards published in the official journal of the European Communities. Medical Equipment is in accordance with UL 60601-1 and CAN/CSA C22.2 No.601.
Safety Instructions On Safety 1. Before connecting the AC power cord to the DC adapter outlet make sure the voltage designation of the DC adapter corresponds to the local electrical supply. 2. Never insert anything metallic into the cabinet openings of the Liquid Crystal Display(LCD) monitor. doing so may create the danger of electric shock. 3. To reduce the risk of electric shock, do not remove cover. No user-serviceable parts inside. Only a qualified technician should open the case of the LCD monitor. 4.
CAUTION Environmental Conditions for transport and Storage - Temperature range within -20°C to 60°C - Relative humidity range 10% to 85% Atrnospheric pressure range within 500 to 1060hPa. Intended Use - This TFT-LCD Monitor is as accessory intended for use with Medical Equipment to display alpha, numerical and graphical data. This symbol alerts the user that important literature concerning the operation of this unit has been included.
EEC Safety Compliance: This display unit meets the requirements of EN-60601-1 so as to conform to the Medical Device Directive 93/42/EEC (general safety information). The monitor should be powered from a center tapped circuit when used in the US at voltages over 120 volts. Monitor is intended for continuous operation.(Using Plug for US: 120V rating -5-15P tYPE, 230V rating-615P type) Recycling : Follow local governing ordinances and recycling plans regarding the recycling or disposal of this requirement.
FCC Information This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference. This monitor can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may interfere with other radio communications equipment. There is no guarantee that interference will not occur in a particular installation.
Surge 1kV differential mode IEC 61000-4-5 2kV common mode 1kV differential mode Mains power quality should be that of a 2kV common mode typical commercial or hospital environment.
Parts 0.01 0.116 0.116 0.2333 0.1 0.368 0.3687 0.7378 1 1.166 1.1660 0.2333 10 3.687 3.6872 0.7375 100 11.660 11.6600 23.333 42" LCD Monitor For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m)can be estimated using the equation applicable to the frequency of the transmitter, where p is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
Mechanical Product Drawing Connector Back Panel Jacks 300 600 AC ON/OFF SWITCH S-VIDEO/Y AC Inlet S-VIDEO/C OPTICAL IN C-VIDEO DVI IN RED /Pr DVI OUT GREEN/Y VGA IN BLUE/Pb RS232C C-SYNC/H-SYNC SDI IN V-SYNC 6-M8(USER MUNT HOLE) SDIOUT 16 - English English - 17
Control OSD Button Function OSD Button Position An 8 button keypad, located in button light corner on the front of the display, allows the user to make adjustments to various display parameters using the On Screen Display (OSD) system. Power Indicating LED Green : Normal mode Amber: Standby mode OFF : Monitor off On-Screen Display (OSD) Function Button 1 POWER : Turns ON/OFF the monitor. 2 MENU : With OSD deactivated, Activated to OSD menu. With OSD activated, Exit from main menu or sub menu.
Power management 6 - (MINUS) : With OSD deactivated, Hot key of the contrast control and decreases the contrast. With OSD activated, decreases the adjustment of the selected function. 7 + (PLUS) : With OSD deactivated, Hot key of the contrast control and increase the contrast. With OSD activated, enter sub menu and increases the adjustment of the selected function. 8 INPUT : Change the display signal source.
Adjusting OSD Color temp COLOR TEMP MODE ADJUST BRIGHTNESS 49 CONTRAST 50 SHARPNESS 50 SATURATION 50 COLOR 0 BACK LIGHT 100 EXIT SELECT CVIDEO 50 BLUE 50 2 RED Red balance (Only Working with USER mode) (Range : 0~100) SELECT 3 GREEN Green balance (Only Working with USER mode) (Range : 0~100) 4 BLUE Blue balance (Only Working with USER mode) (Range : 0~100) MOVE NTSC 60Hz/3.58MHz CVIDEO NTSC 60Hz/3.
Standard Signal table PC Supported Mode Setup 1 SETUP LANGUAGE ENGLISH OSD COLOR 50 Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz) Clock Frequency (MHz) 640 X 350 @70Hz 31.469 70.087 25.175 OSD COLOR Adjust the OSD background from white opaque to half translucent. 720 X 400 @70Hz 31.469 70.082 28.324 640 X 480 @60Hz 31.469 59.940 25.175 OSD POSITION Change the osd position. (9 Positions) 640 X 480 @75Hz 37.500 75.000 31.500 800 X 600 @60Hz 37.879 60.317 40.
Signal connector Pin Assignments VGA (15Pin D-Sub) Pin No. 1 2 3 4 5 6 7 8 Assignment Red Green Blue Ground DDC 5V Standby Cable Connection check Ground-Red Ground-Green Ground-Blue Pin No. 9 10 11 12 13 14 15 Assignment No Connection Ground-Sync Ground DDC Data H.Sync V.Sync DDC Clock 1 Pin No. 1 2 3 5 Assignment T.M.D.S. Data2T.M.D.S. Data2+ T.M.D.S.
Specification RGBHV/RGBS/YPbPr (BNC) Model 6 Assignment RGBS Y Pb Pr Pin No. 1 2 3 4 5 6 Red Pr Green Y Blue Pb H-Sync / C-Sync No Connection V-Sync No Connection Ground R/Pr 1 G/Y B/Pb 2 3 CS/HS 4 VS 5 LCD Panel Synchro nization OPTICAL Pin No. 1 2 3 4 Assignment OPICAL Clock OPICAL Blue OPICAL Green OPICAL Red 1 2 3 4 FS-L4202D Type TFT-LCD Screen Size 42 linch Maximum Resolution 1920 X 1080 @ 60Hz Pixel pitch 0.4845(H) mm X 0.4845(V) mm Display Colors 16.