TABLE OF CONTENT D3FY Sports Inc. Visit www.d3fysports.com for our contact information.
4 WA R N I N G IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES • The D3S marker is not a toy. Misuse may cause serious injury or death. • Please read, understand and follow the directions in the D3S owner’s manual. • Eye protection that is designed specifically for paintball and meets ASTM/CE standards must be worn by user and persons within range. • Recommend 18 years or older to purchase. Person under 18 must have adult supervision. • Always treat the D3S marker as if it were loaded and able to fire.
6 GETTING STARTED 1. Remove the three left hand side grip panel screws(S-048) using a 2mm Allen key that is provided with the D3S. Open the grip panel and attach a 9V battery onto the battery harness(E-076). Close the grip panel and tighten on the three screws(S-048). While closing the panel observe that no wires get caught between the frame and grip panel. 2. Screw the two piece barrel to the front of the D3S. Make sure it threads all the way in and is secure.
9 D3S TRIGGER ADJUSTMENT SCREW F2 BOLT ENGINE CLOCKWISE 10 COUNTER-CLOCKWISE The F2 Bolt engine unique design integrates both the bolt and pressure regulator into a single functioning system. Allowing the marker to operate between 140 and 150 psi. To adjust your trigger. Locate the trigger adjustment screw(S-051) on the upper portion of the trigger. Turning the trigger adjustment screw in (clockwise) with 1.5mm Allen key will shorten the trigger pull.
11 REGULATOR VELOCITY ADJUSTMENT LPC FEED NECK CLOCKWISE COUNTER-CLOCKWISE To adjust the D3S velocity, use a 3mm Allen Key to turn the Regulator screw(S-042). To increase the velocity, turn the screw in (clockwise). To decrease the velocity, turn the screw out (counter-clockwise). Make only small adjustments at a time, shooting 3 to 5 shots between each adjustment to allow the regulator to set its new pressure . LPC FEED NECK NOTE: NEVER ALLOW YOUR D3S MARKER TO EXCEED 180 PSI AND 300 FPS AT ANY TIME.
13 DIRECT DRIVE SYSTEM SOLENOID The Direct Drive System Solenoid directs air to the F2 Bolt engine allowing for a smooth and low operating pressure. Specific air ports were placed to reduce the amount of air needed to propel the paintballs from the barrel without compromising it’s efficiency. Thus giving you more time on the field and less time off.
15 RYSE ON/OFF ASA O-RINGS CLOCKWISE The slick contour profile On/Off ASA raises the airflow from the bottom of the trigger frame up to the regulator without the use of fittings or hose lines. It’s smooth beveled knob gives the player a reliable grip for an effortless transition of switching the knob on or off. To place the RYSE On/Off ASA ON turn the ASA knob clockwise. 16 Item# Description Qty Item# Description Qty O-002 Barrel Tip O-ring (CS 1.78 x 18.
17 O-RINGS SCREWS 18 Item# Description Qty Item# Description Qty Item# Description Qty Item# Description Qty O-035 Airport / Regulator Piston Cover O-ring (CS 1.5 x 9.5 ID) 2 O-062 ASA Knob O-ring (011) 1 S-004 Front Trigger Frame Screw (M5x19L - P0-8) 1 S-016 Solenoid Housing To Valve Plate Screw (M3x14L - P0.5) 1 O-046 Trigger Port O-ring (CS 1.5 x 5.5 ID) 1 O-066 ASA Pin O-ring (CS 2 x 4 ID) 1 S-007 LPC Feedneck Screw (M4x12L - P0.
19 SCREWS SCREWS Item# Description Qty Item# Description Qty S-042 Regulator Adjustment Screw 1 S-060 Solenoid Timing Screw (M4x18L - P0.7) 1 RYSE ASA Screw (M5x28L - P0.8) 2 S-045 Rear Trigger Frame Screw 1 (M5x8L - P0.8) S-063 S-048 Grip Panel Screw (M3x6L - P0.5) 6 S-068 Solenoid Timing Retention Nut (M4) 1 S-051 Trigger Adjustment Screw (M3x5L - P0.5) 2 S-071 Foregrip Retention Screw (M4x6L - P0.
21 INTERNAL PARTS INTERNAL PARTS 22 Item# Description Qty Item# Description Qty Item# Description Qty Item# Description Qty I-011 D3S Receiver 1 I-020 Solenoid Piston Spring 1 I-029 Bolt Guide Piston Spring 1 I-036 Regulator Piston Cover 1 I-012 Ball Detent 2 I-022 Bolt Can 1 I-031 Regulator Piston Housing 1 I-038 Regulator Piston Base 1 I-014 Valve Plate 1 I-024 Bolt 1 I-032 Regulator Piston Seat Seal 1 I-041 Regulator Spring 1 I-017 Solenoid Housing 1
23 INTERNAL PARTS Item# I-052 Description Solenoid Piston EXTERNAL PARTS Qty 1 Item# I-065 Description ASA Pin Qty Item# Description Qty X-001 Barrel Tip 1 I-054 Solenoid Piston Sleeve 1 I-072 Valve Plate Seal Coil Set back plate 1 I-083 Regulator Retention Spring Barrel Back Description Qty X-009 Rhyno Skin Rear Attachment Plate 1 X-043 Regulator Housing 1 X-044 Trigger Frame 1 1 1 X-006 I-056 Item# 1 X-003 Feed Neck Collar 1 1 X-008-L Feed Neck 24 1
25 EXTERNAL PARTS EXTERNAL PARTS Item# Description Qty Item# Description Qty X-050 Trigger 1 X-067 On/Off ASA Knob 1 X-061 Fore Grip 1 X-064-B RYSE On/Off ASA Housing (Black) 1 X-064-G (Green) 1 X-064-T (Teal) 1 X-070 Membrane Pad Item# Description Qty X-079 Right Optic Cover 1 X-081 1 X-080 X-075 Fore Grip Bottom Cover 1 X-078 Left Optic Cover 1 Rhyno Skin Body Cover 1 Wrap around Grip Panels 26 1
27 ELECTRONICS WARRANTY Item# Description Qty Item# Description Qty E-013 ACROS (Eyes) 1 E-069-R SQ Ronin Circuit Board 1 E-047 Trigger Switch 1 E-076 Battery Harness 1 D3FY Sports Inc. provides one year warranty from date of purchase on D3FY OEM products. D3FY will repair or replace any product which is deemed to possess a manufacturer defect. Normal wear and tear is not covered under warranty. REGISTER YOUR MARKER AT WWW.D3FYSPORTS.COM number.
D3S DIAGRAM S-077 X-001 X-080 O-002 X-079 X-006 S-004 S-007 O-005 X-003 X-008 S-077 I-034 X-078 I-036 O-035 E-013 O-005 S-060 I-012 E-057 I-052 I-056 I-054 I-020 S-018 I-014 I-019 S-015 O-053 S-016 I-022 O-062 I-072 S-015 E-047 O-046 O-021 O-005 O-026 O-021 X-070 I-037 I-065 E-076 S-048 I-029 O-030 S-048 X-081 S-018 S-048 E-069-R S-063 I-031 I-028 S-018 X-064 O-021 S-025 S-048 S-048 X-050 X-043 O-027 S-045 O-035 X-067 I-083 I-041 I-024 S-082 X-044 S-071