INSTRUCTION BOOK FOR ViewShare Tensioned Advantage Electrol
Important Safety Instructions Pre-Installation When using your video equipment, basic safety precautions should always be followed, including the following: 1. Carefully unpack case from shipping carton. 1. Read and understand all instructions before using. 2. Set aside the Installation Kit. Items inside will be used during installation. 2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. 3.
Suggested Methods of Installation Method 1 6 1/16" 6 7/16" 7 3/4" Variable Position Mounting Bracket 8" Audience Side Motor End 6 1/16" 3/8" Threaded Rod (Not Included) Attached To Mounting Bracket Electrical Junction Box 6 3/8" Self-Trimming Flange Finished Ceiling 7 3/4" Method 2 3/8" Threaded Rod (Not Supplied) Hanger Bracket 3 7/16" 7 7/16" 6 7/16" 7 3/4" 3
Screen Adjustment for 120V Screens If your Tensioned Advantage Electrol was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and roller assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the 120V Wiring Diagram 1. Locate the wall switch and remove the cover plate from the wall switch and remove the switch from the junction box. 2. Locate the two tactile buttons on the back of the switch.
Wall Switch Installation for 120V Screens 120V Wiring Diagram UP IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 3-conductor connection that is accessible. 3-conductor 20–24 gauge wire can be used in place of the supplied RJ-14 cable to connect the wall switch. Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board.
Video Projector Interface Installation for 120V Screens (Optional) 120V Wiring Diagram with Optional Built-In Video Projector Interface CAUTION: The projector must be turned off before connecting the trigger wires to the projector. Failure to do so may damage the controller. IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 3-conductor connection that is accessible.
Wall Switch Installation for 220/240V Screens 240V Wiring Diagram ILT RJ-9 Pin-Outs (Tab Is Facing Up) IMPORTANT NOTE: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 4-conductor connection that is accessible.
Camera and Speakerphone Installation The following components are necessary for camera and speakerphone installation. Included: • Local CAT5 to USB Extender with Power Supply • 6’ USB Cable • USB Speakerphone • Powered USB Hub You also will need enough CAT5 or CAT5e network cable to run from the ViewShare Advantage to the Local CAT5 to USB Extender. THE CAT5 CABLE IS NOT PROVIDED. The length of the CAT5 cable cannot exceed 200 feet.
Camera and Speakerphone Installation (continued) Camera and Speakerphone Setup You are now ready to run the initial camera setup. The computer will recognize the camera as a new component and load the appropriate drivers. This can take up to several minutes and you may need to follow on-screen instructions. If the computer is using Windows 7 or later version, the computer will automatically detect the camera, choose the proper drivers, and install the drivers without your input.
Troubleshooting Visit www.da-lite.com/products/tutorials.php to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support. Symptom You can contact us by email at info@da-lite.com or by phone at 800.622.3737 or 574.267.8101 with any additional troubleshooting questions. Cause Solution Incorrect line voltage. Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker.
LIMITED WARRANTY – VIEWSHARE PRODUCTS Milestone AV Technologies LLC warrants its Da-Lite branded ViewShare products to the original purchaser only, to be free from defects in materials and workmanship in accordance with the following warranty term: A period of five (5) years for the Advantage screen and related components; and A period of three (3) years for the ViewShare camera and related components.
