The Da-Lite Difference. Instruction Book for Advantage® Electrol® DA-LITE SCREEN COMPANY, INC. 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 Toll Free Fax: 877-325-4832 www.da-lite.com e-mail: info@da-lite.
IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. 3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat. 4.
ADVANTAGE® ELECTROL® INSTALLATION FOR 120V SCREENS 120V WIRING DIAGRAM WITH OPTIONAL BUILT-IN VIDEO PROJECTOR INTERFACE 120V WIRING DIAGRAM FOR STANDARD WALL SWITCH GREEN (GROUND) BLACK (DOWN) WHITE (COMMON) RED (UP) BLACK (HOT) WHITE (COMMON) WHITE JUNCTION BOX LOCATED IN LEFT ENDCAP RED BLACK GREEN MOTOR 110VOLT AC/60HZ POWER SOURCE WHITE RED (UP) BLACK (DOWN) GREEN (GROUND) SPDT SWITCH WITH CENTER OFF FRONT OF WALL SWITCH AC (COMMON) BLACK UP UP STOP AC HOT 120VAC 60HZ 1 AMP OFF THIS SW
ADVANTAGE® ELECTROL® INSTALLATION FOR 220/240V SCREENS 240V WIRING DIAGRAM WITH OPTIONAL BUILT-IN VIDEO PROJECTOR INTERFACE GREEN/YELLOW (GROUND) BROWN (DOWN) BLUE (COMMON) BLACK (UP) BROWN (HOT) BLUE (COMMON) 240VOLT AC/ 50HZ POWER SOURCE 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH: GREEN/YELLOW (GROUND) Da-Lite offers two styles of 240 volt wall switches for standard operation. Please see wiring diagram included in wall switch box included with screen.
SCREEN ADJUSTMENT FOR 120V SCREENS WITHOUT BUILT-IN LOW VOLTAGE CONTROL Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner: Remove two screws to remove access door. NOTE: Use a screw driver or 5/32" Allen wrench to make adjustments. More screen drop 1. Place operating switch in “down” position. 2.
SCREEN ADJUSTMENT FOR 120V SCREENS WITH A BUILT-IN LOW VOLTAGE CONTROL 1. Locate the wall switch and remove the cover plate from the 3-button wall switch and remove the switch from the junction box. 2. Locate the two tactile buttons on the back of the switch. They are square silver with black round buttons. (See Figure 5 for diagram) 3. To adjust the down limit switch, press and hold the down tactile button until the LED on back of switch turns solid red. This will put the motor in limit set mode.
ADVANTAGE® ELECTROL® INSTALLATION 6-1/16" 6-7/16" VARIABLE POSITION MOUNTING BRACKET 7-3/4" MOTOR END 8" AUDIENCE SIDE 6-1/16" 3/8" THREADED ROD (NOT INCLUDED) ATTACHED TO MOUNTING BRACKET ELECTRICAL JUNCTION BOX 6-3/8" SELF-TRIMMING FLANGE FINISHED CEILING 7-3/4" SEE DETAIL A 3.41" 3/8" THREADED ROD (NOT SUPPLIED) 6.42" 7.75" HANGER BRACKET DETAIL A 6 7.
TROUBLESHOOTING Symptom Cause Solution 1. Screen will not operate. Motor does not hum. (a) Incorrect line voltage. (a) Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line. (b) Replace fuse. (c) Reset circuit breaker. (d) Check above. Tighten all loose wire connections. Correct any improper connections. “Down” Position Check for power across black and white leads. “Up” Position Check for power across red and white leads. (b) Blown fuse.
