INSTRUCTION BOOK FOR Dual Format Imager
Important Safety Instructions Pre-Installation When using your video equipment, basic safety precautions should always be followed, including the following: Have space for this unit available on a flat clean surface such as a large table or floor. The work area should be larger than the frame size. If the floor is used, clean papers should be spread to keep all dirt from the Pro-Trim surfaces. 1. Read and understand all instructions before using. 2.
Unpackaging the Frame: 1. The frame will arrive in two separate cardboard boxes. One box will be very long and will house the top & bottom pieces. The smaller cardboard box will house the side frame pieces, hanger hardware, hardware required to put frame together and the wall switch. 3. Inside each box the frame pieces will be individually paper wrapped and taped. Remove all paper from pieces.
Frame Assembly (continued) 3. Assemble left side of frame to the top of frame. The large black metal L bracket will slide into the aluminum extrusion while the small L bracket will slide into the aluminum channel. The pin end bracket needs to be on the outer surface to bolt into the rivnuts of the left side piece. The slat will need to be guided in between the standing fin and the front of the frame. Guide slat in front of fin Loosen set screws for clearence before inserting side pieces. 4.
Frame Assembly (continued) 6. Assemble right side of frame to the top of frame. This is done exactly the same way as the left side. When assembling the unit, route the motor wire behind bracket as shown and attach field wiring box to side of frame (Figure 6 and 7). 7. Assemble bottom of frame to the right and left sections of frame. This is done by sliding the large black metal L brackets into the aluminum extrusion while the small L brackets will slide in the aluminum channels.
Wall Mounting Assembly 1. Depending on size of screen it will be shipped with either 2 wall brackets that are 48" long or 2 wall brackets that are 64" long. Two small L brackets included will be used to hold frame securley to wall at bottom. 2. To install the Dual Format lmager over a Da-Lite Perm-Wall screen you will need to place the supplied wooden spacers between the screen and the wall. A NOTE: Da-Snap, lmager and Cinema Contour frames do not require any spacers. 3.
Wall Mounting Assembly (continued) 6. Hang the frame assembly on the hanger brackets as shown in image. Carefully slide bracket between the top of the frame extrusion and the roller assembly. There is a lip on the back of the frame that wedges itself into the hanger bracket once fully installed on bracket. This is a two person installation. Do not attempt to do this without two people. The top of the frame assembly will be approximately 1 3/4" above the hanger brackets when mounted.
120V Wiring Diagram for Standard Wall Switch NOTE: Junction box located on left upper side of frame Note: A single switch cannot be used to operate more than one screen. Contact Da-Lite for further information. White Black (Up) Red (Down) White Black Red Green AC Common Red UP AC Hot 120VAC 60Hz 1 Amp OFF DOWN Black Black/Yellow SPOT Switch with Center Off CAUTION: This switch can not be used with LVC. ATTENTION: Ce commutateur ne peut être utilisé avec le tableau de contrôle basse tension.
Post Installation Procedures Travel Adjustments: 1. Masking travel is stopped automatically in the up and down positions by limit switches that are properly adjusted at the factory. Should it be necessary to adjust the stop positions, proceed in the following manner: Test installation by carefully running mask surface up and down 2-3 times. Be prepared to stop screen. Standard Duty Cycle: 1 MIN. ON I 3 MIN. OFF. CAUTION! Excessive countinous operation may cause overheating.
Troubleshooting Symptom Cause Solution Incorrect line voltage. Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line. Blown fuse. Replace fuse. Tripped circuit breaker. Reset circuit breaker. Masking System will not operate. Motor does not hum. Check above. Tighten all loose wire connections. Correct any improper connections. No power to operating switch or junction. Down Position Check for power across black and white leads.
LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the factory.