INSTRUCTION BOOK FOR IDEA™ Panoramic
Preparation Note: It requires at least four people to assemble an IDEA Panoramic. To maintain optimal projected image geometry and screen alignment, a flat and straight wall free from obstructions and angular distortions should be used. Choose a clean work area for assembly using padded material or other soft, clean materials. The work area should be larger than the overall screen size and directly in front of the location where the screen is to be installed.
Hardware Provided Wall Brackets Included Center Panel Viewing Area (H x W) Center Panel Wall Brackets Side Panel Wall Brackets 36¾" x 144¾" 36" x 64" (2) 28" (2) 28" 36¾" x 144¾" 36" x 57½" (2) 28" (2) 28" Item Number Overall Dimensions 27966 27981 27963 46¾" x 144¾" 46" x 81¾" (2) 28" (2) 28" 27978 46¾" x 144¾" 46" x 73½" (2) 28" (2) 28" 27960 50¾" x 144¾" 50" x 89" (2) 44" (2) 18" 27975 50¾" x 144¾" 50" x 80" (2) 28" (2) 28" 27957 53¾" x 144¾" 53" x 94¼" (2) 44" (2) 18
Assembly Instructions for Panoramics with 24” Marker Tray 1. Carefully unpack unit and place all panels on top of the clean work area. The viewing surface of each panel must face down. NOTE: For optimal seam alignment, use labels on the back side of each panel to arrange for assembly. 5. Use ⅜” open wrench or socket driver and (4) 10-32 nuts to attach seam brace onto the studs on the top and bottom of screen frame at the panel seam. Tighten all four nuts once attached to the frame (Figure 2).
Wall Mounting for Panoramics with 24” Marker Tray NOTE: The screen is shipped with four wall brackets and lengths shipped vary by screen size. Two brackets will be used on the center panel and one bracket on each of the side panels. Measure gap on each side panel to determine which two brackets will be used with these panels. These brackets will be of an equal length. The remaining two brackets (also of an equal length) will be used to hold the weight of the center panel.
Wall Mounting Instructions for Screens with 24” Marker Tray (continued) 5. Repeat Steps 3-4 to install the (4) remaining L-brackets for the side panels. NOTE: At this point, all six L-brackets will be mounted on the wall; two L-brackets for each panel. Do not proceed if all six-L brackets are not level with each other on the wall. Steps 6-7 require at least four people.
Assembly Instructions for Panoramics with Full Length Marker Tray 1. 5. Use ⅜” open wrench or socket driver and (4) 10-32 nuts to attach seam brace onto the studs on the top and bottom of screen frame at the panel seam. Tighten all four nuts once attached to the frame (Figure 6). Carefully unpack unit and place all panels on top of the clean work area. The viewing surface of each panel must face down. NOTE: For optimal seam alignment, use labels on the back side of each panel to arrange for assembly.
Wall Mounting for Panoramics with Full Length Marker Tray NOTE: The screen is shipped with four wall brackets and lengths shipped vary by screen size. Two brackets will be used on the center panel and one bracket on each of the side panels. Measure gap on each side panel to determine which two brackets will be used with these panels. These brackets will be of an equal length. The remaining two brackets (also of an equal length) will be used to hold the weight of the center panel.
Wall Mounting for Panoramics with Full Length Marker Tray (continued) Steps 3-8 require at least four people. Place one person on the far left end of the screen, one person at the left panel seam, one person at the right panel seam and one person on the far right end of the screen. More people can be utilized as needed. When lifting the screen off of the clean work area to the wall and then onto the wall, it is crucial that the screen remain coplanar and does not bend at the seams.
Wall Mounting for Panoramics with Full Length Marker Tray (continued) 7. Using all four people, carefully lift the fully assembled three panel screen with the marker trays to an upright position and briefly place underneath the mounted wall brackets. The screen will be parallel to the wall at the end of this step. 8. Using all four people, carefully and in a smooth motion lift the screen to hang it on the four installed wall brackets.
Cleaning The supplied cleaning cloth can be used to clean marks on the screen surface made by everyday dry erase marker usage. Use clean or dry sections of the microfiber cloth when erasing the screen. This is important to prevent smearing on the screen while cleaning. To clean persistent marks from dry erase markers, use the supplied Da-Lite spray cleaner and cleaning cloth. Windex Original spray cleaner can be used to remove tough to clean or smeared areas.
LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the factory.