Instruction Book for TENSIONED CountouR® Electrol®
IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. 3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat. 4.
INSTALLATION (continued) 3. Make sure the bracket is level. 4. Hang the screen case on the wall mount bracket as shown in Figure 2. Be sure the case is fully seated on the bracket. 5. Tighten the two stop screws against the wall mount bracket using a #2 Phillips screwdriver (Figure 1). Wall Ceiling Flush Mount 1. The ceiling hook brackets are attached to the top side of the housing. They must be removed prior to ceiling flush mount.
electrical installation 1. Open the junction box on the left end of the case using a #2 Phillips screwdriver. Install electrical connections that apply to your unit. Make sure to review the wiring diagram for proper hook up. Replace the junction box cover. NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70. 2. Test installation by running screen up and down a few times.
SCREEN ADJUSTMENT FOR 120V SCREENS If your Tensioned Advantage Electrol was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and roller assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the 120V Wiring Diagram 1. Locate the wall switch and remove the cover plate from the wall switch and remove the switch from the junction box. 2. Locate the two tactile buttons on the back of the switch.
® CONTOUR TENSIONED ELECTROL Contour®®INSTALLATION ELECTROL® INSTALLATION FOR 120V SCREENS FOR 120V SCREENS 120V WIRING DIAGRAM UP 3-conductor 20–24 gauge wire can be used in place of the supplied RJ-14 cable to connect the wall switch. Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board. STO P DO WN IMPORTANT Note: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used.
TENSIONED Contour® ELECTROL® INSTALLATION FOR 120V SCREENS 120V Wiring Diagram with Optional Built-In Video Projector Interface IMPORTANT Note: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 3-conductor connection that is accessible. CAUTION: The projector must be turned off before connecting the trigger wires to the projector. Failure to do so may damage the controller.
TENSIONED Contour® ELECTROL® INSTALLATION for 240v Screens 240V WIRING DIAGRAM ILT RJ-9 Pin-Outs (Tab Is Facing Up) IMPORTANT Note: The wall switch is REQUIRED to make any limit switch adjustments, EVEN if a third party control system is used. Therefore, it is advised to wire the switch or provide a 4-conductor connection that is accessible.
TROUBLESHOOTING Visit www.da-lite.com/products/tutorials.php to find installation and troubleshooting tutorials. You will also find a link to Live Chat for interactive support. Symptom Screen will not operate and motor does not hum. You can contact us by email at info@da-lite.com or by phone at 800.622.3737 or 574.267.8101 with any additional troubleshooting questions. Cause Solution Incorrect line voltage. Verify 115-125V (or 220-240V). If insufficient voltage, rewire incoming electric line.
LIMITED FIVE YEAR WARRANTY ON DA-LITE TENSIONED CONTOUR® ELECTROL PRODUCTS ONLY Da-Lite Screen Company LLC warrants these products to the original purchaser only, to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original purchaser provided they are properly operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the factory.
