I n stall at i o n I n str u ct i o n s B u i lt - I n R e f r i g e r ato rs Part No. 100500 Rev.
Table of Refrigerator Safety........................................................................1 Design Specifications................................................................2-6 Product Dimensions.....................................................................2 Door Swing Dimensions..............................................................2 Custom Overlay Panels............................................................3-6 Installation Specifications.................................
Design Specifications Product Dimensions ◊ The depth from the front of the top grill (w/o decorator panel) to the back of the refrigerator chassis is 25 1/4” (641mm). ◊ The depth from the rear of the top grill to the back of the refrigerator chassis is 23 13/16” (605mm). ◊ The power cord is 40” (1016mm) long.
Design Specifications Custom Overlay Panels (A) Grille Panel The decorator panels for overlay models cover the door trim for an attractive, seamless look that flows into the overall design of the room. This application is often accomplished by using three panels: the decorative front panel, a spacer panel of .10-inch thickness, and a 1/4-inch backer panel.
Design Specifications Overlay Panel Specifications NOTES: (See Illustrations on page 3.
Design Specifications Custom Toe Kickplate Specifications If using custom toe kickplate with your Dacor® Built-In Refrigerator, refer to the following specifications. Angled cut for thicker plates Panel thicker than 3/16" 6 1/4" 5 5/8" 15/16" Typ 4 13/16" 7/8" (A) 5/16" (A) (B) (B) 2 3/16" Typ 1 13/16" 3/4" Typ 1 1/8" Typ Cut out for Dispenser (B) (A) (B) R. 1/2" 3" 3 3/4" Allow relief here for dispenser models with panels thicker than 3/16" “C” Model 42-Inch 48-Inch Hole “A”Dia.
Design Specifications 90˚ Door Opening (Top View) Cabinet Trim 90° Door Stop Both doors are designed to open 135°. To restrict one or both doors to a 90° opening, use the door stops supplied in this kit.
Tools and IMPORTANT: Installation Specifications Parts ◊ Installer: Leave these Installation Instructions with the homeowner. ◊ Homeowner: Keep these Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use. Tools needed: Make sure that you have the necessary tools and materials available for a proper installation.
Installation Specifications Electrical Requirements Rough-In Dimensions ◊ The solid sofit or ceiling should be within 1” (25mm) above the refrigerator. If the solid sofit is higher than 1” (25mm) or one is not available, then the refrigerator must be braced to prevent tipping during use. If the anti-tip blocking is need. (see “Anti-Tip Blocking” on page 9) NOTE: A clearance of 1/2” (13mm) must be maintained above the top grill in order for the top grill to be opened.
Installation Instructions Unpack Refrigerator WARNING Tip over Hazard – Refrigerator is top heavy and tips easily when not completely installed, Keep doors taped closed until refrigerator is completely installed. Use two or more people to move and install refrigerator. Failure to do so can result in death or serious injury. Anti-Tip Blocking Blocking the Refrigerator If there is a solid sofit or ceiling above the unit and the clearance is 1” (25mm) or less you will not need to block the unit.
Installation Instructions Water Line Connection ◊ Before attaching the copper tubing to the unit, flush at least 2qt (1.9L) of water through the copper tubing into a bucket to get rid of any particles in the water line. Level Unit ◊ Slide the unit in place and raise the front and rear levelers until the unit touches the brackets. (Use a 3/8” socket to raise and lower the unit.) ◊ Check for leaks around the saddle valve. Do not overtighten the clamp or sleeve. This will crush the copper tubing.
Installation Instructions Install Custom Panels Panel Installation Before you begin installing panels, refer to the “Custom Panel Specifications” for overlay models and verify that you are working with the panel design called for in your installation. If you have chosen the stainless steel design, your refrigerator has been shipped complete with a finished stainless steel front. It will not be necessary to install panels or handle hardware.
insTallaTion insTRuCTions 7. Remove the four #15 Torx plastic collar screws from the fountain/escutcheon collar. Terminals Control Panel 7 8. Place the fountain/ escutcheon collar onto the backer panel. Use tape to hold in place. Stainless Steel Splashguard Spill Tray Grille CAUTION 8 9. Open the freezer door and slide panel onto the door. WARNING – Do not exceed the panel dimensions shown in the chart on page 4 for the grille panel.
Installation Instructions Side Panel Installation If using side panels with the Dacor® Built-In Refrigerator, they will need to be 1/4-inch thick. Slide the panel into position and secure with screws indicated by the shaded area. A 3/16-inch spacer is required between the cabinet and side panel. A 1/2-inch thick by 10 1/4- inch tall spacer is required if the side panel extends up into the machine compartment area on the refrigerator side.
Installation Instructions Installation Checklist The importance of the proper installation of your Dacor Built-In Refrigerator cannot be overemphasized. Proper installation is the responsibility of the homeowner. IMPORTANT: To ensure a safe and proper installation, the following checklist should be competed by the installer to ensure that no part of the installation has been overlooked.
Notes 15
Notes 16
Web Site: Phone: www.dacor.com (800) 793-0093 The information and images in this book are the copyright property of Distinctive Appliances, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Distinctive Appliances, Inc. ©Distinctive Appliances, Inc. all rights reserved.