Installation Guide

01
Uncrating the refrigerator
Ƹ͝ϑʀθʪиϩ˵ʪɵͱ̷ϩϑ
đՑуՌՋ׋ՌՋʪɇ
• Remove the brackets from the pallet by
unscrewing the bolts (ve per bracket).
02
Attaching the anti-tip bracket
Cabinet
Height

đՏуՎՐ׋Վʪɇ
Wooden Wall
󰞌
Concrete wall
đՏуՎՐ׋Վʪɇ
ØՑуՎՋ׋Վʪɇ
󰞌
󰞔
ՍٓطՐՋظ
ƊΧɇʀʪθطиͱͱʒظ
ΧΧ̷̈ɇ͝ʀʪ ΧΧ̷̈ɇ͝ʀʪ
󰞆
• Bracket height is measured from the oor
and depends on the cabinet height.
• Attach the anti-tip brackets. Ensure the
screws hold the bracket tightly.
• The anti-tip brackets must extend at least
2” (50 mm) over the appliance to secure the
appliance. If this minimum length cannot
be observed for structural conditions
it is possible to do this by fastening a
spacer(wood) behind the anti-tip angle.
Cabinet Height A
1 83 1/2”(2121 mm) 79 1/2”(2019 mm)
2 83 3/4”(2127 mm) 79 5/8”(2023 mm)
3 84”(2134 mm) 79 7/8”(2030 mm)
4 84 1/4”(2140 mm) 80 1/8”(2036 mm)
03
Cabinet special requirements
5”
(127)
D
A
C
E
F
B
Electric supply
location
6”
(154)
ø1/4”(6.5)
1”
(25.4)
Water supply
location
A : Cabinet Width
B : Cabinet Depth
C : Cabinet Height
D : Electrical supply width location
E : Electrical supply height location
F : Water supply outlet location
*B : Includes the standard door panel
thickness with 1/4”
* Installation insidea cabinet of
this width allows the refrigerator
trim to be attached directly to the
surrounding cabinets.
• Connect refrigerator power cord plug to a
properly earthed receptacle. Set the Master
Power Switch to the “I” (ON) position.
• Check to make sure power to refrigerator
is on by opening refrigerator door to see if
interior lights are on.
36”
A 36” (915 mm) D 26” (660 mm)
B 25” (635 mm) E 80” (2032 mm)
C 84” (2,134 mm) F 9” (228 mm)
04
Moving the refrigerator into its enclosure
ĮЭʪθ̷ɇцƟцΧʪ
Aɇɵ̈
Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ
ƟͱΧӬʪи
ƟͱΧӬʪи
θɇ͔ʪ̷ʪϑϑƟцΧʪ
Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ
Aɇɵ̈
â̈˝
طťͱϑ̈ϩ̈ͱ̈͝͝˝ɇ̈ʒظ
ĮЭʪθ̷ɇц
θɇ͔ʪ̷ʪϑϑ
󰞓
ťɇ͝ʪ̷
θʪɇʒц
ťɇ͝ʪ̷
θʪɇʒц
ťɇ͝ʪ̷
θʪɇʒц
ťɇ͝ʪ̷
θʪɇʒц
Ռժٗٗ
طՏՋ͔͔ظ
Ռժٗٗ
طՏՋ͔͔ظ
• According to the type of cabinet, a jig
(positioning aid) can be used to align the
refrigerator’s custom door panel with cabinet
by marking vertical line on the cabinet.
• Position the cabinet side chassis to align with
your vertical line.
05
Leveling the refrigerator
θͱ͝ϩ
ʒ̟Їϑϩɇɵ̷ʪϑ˵ɇ˙ϩ
طՎ؏Փٓ׋ՌՋ͔͔ظ
đɇу
ՍՋ͔͔
âɇʀ̧ϩцΧʪط˵ʪ̈˝˵ϩɇʒ̟Їϑϩ͔ʪ͝ϩظ
ŵʪɇθ
• Attach the refrigerator’s top cover and trim
top cover to the hook at the top front of the
chassis.
• Using your drill and the bit shown below,
engage each of the refrigerator’s adjuster
shafts in turn, and level the refrigerator.
( CW ↑, CCW ↓)
Adjust the gap between the furniture and
upper chassis cover to 1/8 in. (3mm ).
• The front and rear leveling legs have a
maximum height adjustment of 3/4 in.
(20mm).
Installation guide
06
Securing the refrigerator
̈уʪʒ̷ͱʀɇϩ̈ͱ͝
ƟͱΧǤ̈ʪи
󰞊
ťɇ͝ʪ̷θʪɇʒц Aɇɵ̈
Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ
طƟ²ظđՏуՌՏ׋ՌՍʪɇ
• Remove freezer box.
• Secure the refrigerator to its enclosure with
(TH) M4 x 14 screws (6 screws per side, as
shown in the graphic).
07
Attaching the Front-Panel Insulation
󰞕
󰞖
Ã͝ϑЇ̷ɇϩͱθ
Ã͝ϑЇ̷ɇϩͱθ
ՏٓطՌՋՍ͔͔ظ
ՏٓطՌՋՍ͔͔ظ
• Attach the insulation to the front of
refrigerator door. (Ensure the mounting
position is correct.)
• Center the door panel and the insulation .
• Attach the insulation 4 in. (102 mm) from top
of the door. (See the graphic.)
08
Attaching the Custom-Door-Panel Brackets
Ƹťť׊ՌՋʪɇ؏øĮǮ׊ՌՋʪɇ
󰞉
θ̈ʒ˝ʪUͱͱθøͱи
ط²ظđՏуՌՏ׋ՍՋʪɇ
ŵʪʀͱ͔͔ʪ͝ʒʪʒɇϑϑʪ͔ɵ̷ц˵ͱ̷ʪ
θʪʪіʪθUͱͱθ
θ̈ʒ˝ʪUͱͱθƸΧ
Custom Panel: STS
• Drive 10 screws each to the top and bottom
brackets as shown in the graphic.
(The other holes on each side of the bracket
are for a different application.)
Ƹť
øĮǮ
Panel
Template
REFFRE
ط²ظđՏуՌՏ׋ՍՋʪɇ
Ƹťť׊ՌՋʪɇ؏øĮǮ׊ՌՋʪɇ
󰞉
Custom Panel: Wood, Other
• The template informs you the position of the
bracket and holes.
• Mark hole positions on every corner of the
panel according to the template and drive
the screws into the holes.
θͱ͝ϩ
Ɗʀθʪи
ծٓ
կٓ
9ɇʀ̧
9θɇʀ̧ʪϩ
ط²ظđՏуՌՏ׋ՍՋʪɇ
Ƹťť׊ՌՋʪɇ؏øĮǮ׊ՌՋʪɇ
󰞉
θ̈ʒ˝ʪUͱͱθ
θʪʪіʪθUͱͱθ
Ɗʀθʪи²ͱ̷ʪ
Custom Panel: Recessed Back, Other
• If, by the nature of its design, the panel
cannot be attached at the center of the
bracket, use the whichever suitable screw
holes on the sides of the bracket to attach
the panel.
09
Aligning the panel
UͱЇɵ̷ʪϩ˵θʪɇʒʪʒ
ɵͱ̷ϩ
Ɗ̈ʒʪϑʀθʪи
Ęͱ׵Սϑʀθʪи
Ęͱ׵Ռϑʀθʪи
đՑуՌՍ׋ՌՍʪɇ
kɇʀ˵ՌՍϑʀθʪиϑΧʪθUͱͱθ
󰞈
ťɇ͝ʪ̷Χͱϑ̈ϩ̈ͱ͝ɇʒ̟Їϑϩʪθ
󰞇
đՌՎ
• There are two panel-adjustment mechanisms
at the top and two at the bottom of the door.
• Adjust the panel so it aligns with the
surrounding cabinetry.
• A side screw to shift the panel side to side;
Screw 1 to shift the panel forward/backward;
Screw 2 to set the panel in place.
• To attach the Panel to the Door, screw nuts
snugly onto the double-threaded bolts. (2
nuts per door)
DA68-03576B-01
CAUTION
Please read the installation insturctions carefully before you install the product.
No NAME Q'TY
1 PANEL BRACKET RL-UP RR-LOW 2
2 PANEL BRACKET RR-UP RL-LOW 2
3 PANEL BRACKET FRE 2
4 ANTI-TIP BRACKET 1
5 NUT-HEXAGON FLANGE 6
6 BOLT-HEX 36
7 SCREW-TAPPING 62
8 SCREW-TAPPING 12
9 SCREW-TAPPING 5
10 SCREW-TAPPING 3
11 TOP TABLE 1
12 LOWER DOOR CAP REF LEFT 1
13 LOWER DOOR CAP REF RIGHT 1
14 UPPER CAP DOOR FRE 1
15 LOWER CAP DOOR FRE 1
16 TRIM TOP COVER 1
17 GAP GUIDE 1
18 HOLDER LOCK 3
19 INSULATOR-REF 2
20 INSULATOR-FRE 1
21 BRACKET TEMPLATE-REF 1
22 BRACKET TEMPLATE-FRE 1
23 INSTALLATION GUIDE 1
     
M13 M6 x 12
     
(FH) M4 X 14 (TH) M4 X 14 M5 x 16 M4 x 35
     
 
INSTALLATION
GUIDE