Installation Guide
01
Uncrating the refrigerator
Ƹ͝ϑʀθʪиϩ˵ʪɵͱ̷ϩϑ
đՑуՌՋՌՋʪɇ
• Remove the brackets from the pallet by
unscrewing the bolts (ve per bracket).
02
Attaching the anti-tip bracket
Cabinet
Height
đՏуՎՐ
Wooden Wall
Concrete wall
- For 18”, 24” ,30” models : 3 ea
- For 36” models : 6 ea
- 3 screws/holder locks per bracket
đՏуՎՐ
ØՑуՎՋ
ՍٓطՐՋظ
ƊΧɇʀʪθطиͱͱʒظ
ΧΧ̷̈ɇ͝ʀʪ ΧΧ̷̈ɇ͝ʀʪ
• Bracket height is measured from the oor
and depends on the cabinet height.
• Attach the anti-tip brackets. Ensure the
screws hold the bracket tightly.
• The anti-tip brackets must extend at least
2” (50 mm) over the appliance to secure the
appliance. If this minimum length cannot
be observed for structural conditions
it is possible to do this by fastening a
spacer(wood) behind the anti-tip angle.
Cabinet Height A
1 83 1/2”(2121 mm) 79 1/2”(2019 mm)
2 83 3/4”(2127 mm) 79 5/8”(2023 mm)
3 84”(2134 mm) 79 7/8”(2030 mm)
4 84 1/4”(2140 mm) 80 1/8”(2036 mm)
For 36” models, place 2 anti-tip brackets at intervals. For the other models, use one anti-tip bracket.
03
Cabinet special requirements
A : Cabinet Width
B : Cabinet Depth
C : Cabinet Height
D : Electrical supply width location
E : Electrical supply height location
F : Water supply outlet location
*B : Includes the standard door panel
thickness with 1/4”
* Installation insidea cabinet of
this width allows the refrigerator
trim to be attached directly to the
surrounding cabinets.
5”
(127)
D
A
C
E
F
B
Electric supply
location
6”
(154)
ø1/4”(6.5)
1”
(25.4)
Water supply
location
• Connect refrigerator power cord plug to a
properly earthed receptacle. Set the Master
Power Switch to the “I” (ON) position.
• Check to make sure power to refrigerator
is on by opening refrigerator door to see if
interior lights are on.
CAUTION
After power has been established, turn the
Master Power Switch to the “O” (OFF) position.
18” 24” 30” 36”
A
18’(457 mm) 24”(610 mm) 30”(762 mm) 36”(915 mm)
B
25”(635 mm) 25”(635 mm) 25”(635 mm) 25”(635 mm)
C
84”(2,134 mm) 84”(2,134 mm) 84”(2,134 mm) 84”(2,134 mm)
D
8”(203 mm) 14”(356 mm) 20”(508 mm) 26”(660 mm)
E
80”(2032 mm) 80”(2032 mm) 80”(2032 mm) 80”(2032 mm)
F
3”(76 mm) 5 1/2”(140 mm) 6”(152 mm) 9”(228 mm)
04
Moving the refrigerator into its enclosure
ĮЭʪθ̷ɇцƟцΧʪ
ťθͱʒЇʀϩ
ťθͱʒЇʀϩ
Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ
ƟͱΧӬʪи
ƟͱΧӬʪи
θɇ͔ʪ̷ʪϑϑƟцΧʪ
Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ
â̈˝
طťͱϑ̈ϩ̈ͱ̈͝͝˝ɇ̈ʒظ
ĮЭʪθ̷ɇц
θɇ͔ʪ̷ʪϑϑ
ťɇ͝ʪ̷
θʪɇʒц
ťɇ͝ʪ̷
θʪɇʒц
ťɇ͝ʪ̷
θʪɇʒц
ťɇ͝ʪ̷
θʪɇʒц
Ռժٗٗ
طՏՋ͔͔ظ
Ռժٗٗ
طՏՋ͔͔ظ
• Before moving the refrigerator into its
enclosure, attach cabinet side insulators to
both side of the refrigerator properly. Refer
to gures below.
• According to the type of cabinet, a jig
(positioning aid) can be used to align the
refrigerator’s custom door panel with cabinet
by marking vertical line on the cabinet.
• Position the cabinet side chassis to align with
your vertical line.
θͱ͝ϩ
ŵʪɇθՌՓٓ؏ՍՏٓ؏ՎՋٓ؏ՎՑٓ ՍՏٓ؏ՎՋٓ
θʪʪіʪθθ̈ʒ˝ʪ θʪʪіʪθθ̈ʒ˝ʪ
ՌՓٓ؏ՍՏٓ؏ՎՋٓ؏ՎՑٓ ՎՑٓ
Ռ؏Տٓ
طՑ͔͔ظ
Ռ؏Փٓ
طՎ͔͔ظ
Ã͝ϑЇ̷ɇϩͱθ
ʀ˵ɇϑϑ̈ϑ
Įŵ
ƟͱΧǤ̈ʪи
θͱ͝ϩ
ŵʪɇθՌՓٓ؏ՍՏٓ؏ՎՋٓ ՎՑٓՎՑٓ
Ɗ̈ʒʪǤ̈ʪи
Attaching insulators: For more information, refer to the installation manual.
• Single Installation
Example of 36” installation
• Pair Installation
Installation guide
05
Leveling the refrigerator
θͱ͝ϩ
ʒ̟Їϑϩɇɵ̷ʪϑ˵ɇ˙ϩ
طՎ؏ՓٓՌՋ͔͔ظ
ɇу
ՍՋ͔͔
âɇʀ̧ϩцΧʪط˵ʪ̈˝˵ϩɇʒ̟Їϑϩ͔ʪ͝ϩظ
ŵʪɇθ
• Attach the refrigerator’s top cover and trim
top cover to the hook at the top front of the
chassis.
• Using your drill and the bit shown below,
engage each of the refrigerator’s adjuster
shafts in turn, and level the refrigerator.
( CW ↑, CCW ↓) Adjust the gap between the
furniture and upper chassis cover to 1/8 in.
(3mm ).
• The front and rear leveling legs have a
maximum height adjustment of 3/4 in.
(20mm).
06
Securing the refrigerator
ƟͱΧǤ̈ʪи
طƟ²ظđՏуՌՑՌՍʪɇ
ťɇ͝ʪ̷θʪɇʒц Aɇɵ̈
Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ
Aɇɵ̈͝ʪϩϑ̈ʒʪʀ˵ɇϑϑ̈ϑ̈уʪʒ̷ͱʀɇϩ̈ͱ͝
• Secure the refrigerator to its enclosure with
(TH) M4 x 16 screws (6 screws per side, as
shown in the graphic).
07
Attaching the Front-Panel Insulation
Ã͝ϑЇ̷ɇϩͱθ
ՏٓطՌՋՍ͔͔ظ
• Attach the insulation to the front of
refrigerator door.
(Ensure the mounting position is correct.)
08
Attaching the Custom-Door-Panel Brackets
STS Type
Wood Type
Recessed Back Type
Ƹť ťɇ͝ʪ̷
øĮǮ
ط²ظđՏуՌՏՍՋʪɇ
ƸťťՌՋʪɇ؏øĮǮՌՋʪɇ
Ƹť
øĮǮ
Panel
Panel
Template
For Lower
(Align the bottom of the panel)
For Upper
(Align the top of the panel)
BRACKET TEMPLATE
COLUMN
Align the side of the panel
Align the side of the panel
ط²ظđՏуՌՏՍՋʪɇ
ƸťťՌՋʪɇ؏øĮǮՌՋʪɇ
Ɗʀθʪи²ͱ̷ʪ
Front
Ɗʀθʪи
ծٓ
կٓ
Back
9θɇʀ̧ʪϩ
ط²ظđՏуՌՏՍՋʪɇ
ƸťťՌՋʪɇ؏øĮǮՌՋʪɇ
Custom Panel: STS
• Drive 10 screws each to the top and bottom
brackets as shown in the graphic.
(The other holes on each side of the bracket
are for a different application.)
Custom Panel: Wood, Other
• The template informs you the position of the
bracket and holes.
• Mark hole positions on every corner of the
panel according to the template and drive
the screws into the holes.
Custom Panel: Recessed Back, Other
• If, by the nature of its design, the panel
cannot be attached at the center of the
bracket, use the whichever suitable screw
holes on the sides of the bracket to attach
the panel.
09
Aligning the panel
ťɇ͝ʪ̷Χͱϑ̈ϩ̈ͱ͝ɇʒ̟Їϑϩʪθ
UͱЇɵ̷ʪϩ˵θʪɇʒʪʒ
ɵͱ̷ϩ
Ɗ̈ʒʪϑʀθʪи
ĘͱՍϑʀθʪи
ĘͱՌϑʀθʪи
đՑуՌՍՌՍʪɇ
kɇʀ˵ՌՍϑʀθʪиϑΧʪθUͱͱθ
đՓ
• There are two panel-adjustment mechanisms
at the top and two at the bottom of the door.
• Adjust the panel so it aligns with the
surrounding cabinetry.
• A side screw to shift the panel side to side;
Screw 1 to shift the panel forward/backward;
Screw 2 to set the panel in place.
• To attach the Panel to the Door, screw nuts
snugly onto the double-threaded bolts. (2
nuts per door)
DA68-03631A-03
No NAME
Q'TY
18”/24”/30” 36”
1 PANEL BRACKET 2 2
2 ANTI-TIP BRACKET 1 2
3 NUT-HEXAGON FLANGE 2 2
4 BOLT-HEX 12 12
5 SCREW-TAPPING 22 22
6 SCREW-TAPPING 24 24
7 SCREW-TAPPING 3 6
8 TOP TABLE 1 1
9 LOWER DOOR CAP 1 1
10 CAP 2 2
11 GAP GUIDE 1 1
12 TRIM TOP COVER 1 1
13 HOLDER LOCK 3 6
14-1 CABI SIDE INSULATOR 4 2
14-2 CABI SIDE INSULATOR - 2
15 INSULATOR 2 2
16 BRACKET TEMPLATE 1 1
17 INSTALLATION GUIDE 1 1
CAUTION
Please read the installation insturctions carefully before you install the product.
For Lower
(Align the bottom of the panel)
For Upper
(Align the top of the panel)
BRACKET TEMPLATE
COLUMN
Align the side of the panel
Align the side of the panel
(FH) M4 x 14
-
1
INSTALLATION
GUIDE
(TH) M4 x 16
-
2
M8 M4 x 35
M6 x 12