User's Manual

ManualsBrandsDacor ManualsRefrigeratorsDacor Dacor Refrigerator IF48NBOL

PLANNING

GUIDE

Web: http://www.Dacor.com

Corporate Phone: 800-793-0093

Specifications are subject to change without notice.

See installation instructions for additional details.

11.14

42” and 48” Wide

Built-In Refrigerators

EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS,

IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL

1/6

Op e n i n g Di m e n s i O n s

To avoid tipping during use, the solid soffit must be within 1” ◊

(2.5 cm) maximum above the refrigerator. If the solid soffit

is higher than 1” (2.5 cm) or one is not available, then the

refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the

rear wall studs 80” to 90” (203 cm to 229 cm) above the floor.

See installation instructions for more information.

NOTE:Aclearanceof¹⁄2” (1.3 cm) must be maintained above

the top grille in order for the top grille to be removed.

(10.2 cm)

¹/2

" (212.1 cm) min.

³/4" (215 cm) max.

to bottom of solid soffit

24"

(60.96 cm) min.

77"

(196 cm)

Width

(see chart following)

Revised

04/22/08

(1.3 cm)

Model Series Cutout Width A

EF42, IF42 41½” (105.4 cm) to 41¾” (106.1 cm)

EF48, IF48 47½” (120.7 cm) to 47¾” (121.3 cm)

NOTE: Flooring under refrigerator must be at same level as the

room. Face of cabinetry must be plumb.

A grounded 3 prong electrical outlet should be placed within ◊

4” (10.2 cm) of the right side cabinets or end panel. See

Electrical Requirements for more information.

The water shutoff should be located in the base cabinet on ◊

either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the

plumbing for the water line can come through the floor or

the back wall. See Water Supply Requirements for more

information.

See Page 11.15

Summary of content (6 pages)

PAGE 1
EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide Built-In Refrigerators Revised 04/22/08 1/6 PLANNING GUIDE Opening Dimensions ◊ To avoid tipping during use, the solid soffit must be within 1” (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1” (2.5 cm) or one is not available, then the refrigerator must be braced.
PAGE 2
EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL Revised 04/22/08 42” and 48” Wide Built-In Refrigerators 2/6 PLANNING GUIDE Electrical Requirements Water Supply Requirements The electrical circuit must meet all local codes and ordinances. ◊ All installations must meet local plumbing code requirements. Recommended Grounding Method ◊ The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible area.
PAGE 3
EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide Built-In Refrigerators Revised 04/22/08 Door Swing Dimension The location must permit both doors to open to a minimum of 90°. Allow 4½” (11.4 cm) minimum space between the side of the refrigerator and a corner wall. 3/6 NOTE: More clearance may be required if you are using overlay panels, custom handles or extended handles on a IF series model. To adjust the door swing, see the installation instructions.
PAGE 4
EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide Built-In Refrigerators Revised 04/22/08 Custom Panels and Handles - IF42/IF48 Series Models Install the panels after moving the refrigerator into place. The weight of the overlay panels cannot exceed: The custom panels must have backer panels attached in order to mount them to the refrigerator. It is most common to work with three panels, as shown in the graphic below. A decorative overlay panel, a ¹/8” (3.
PAGE 5
EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL 42” and 48” Wide Built-In Refrigerators Revised 04/22/08 5/6 PLANNING GUIDE Custom Side Panels - IF42/IF48 Inset Installation Dimensions Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset or Recessed Inset panel installation for models IF42 and IF48. 1.
PAGE 6
EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL Revised 04/22/08 42” and 48” Wide Built-In Refrigerators 6/6 PLANNING GUIDE Custom Side Panels - EF42/EF48 Inset Installation Dimensions Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an inset, flush or recessed inset panel installation for models EF42 and EF48. 1.