cacor a rare rae Installation 24-Inch Built-in Model DDWF24S Part No. 106811 Rev.
Table of Contents Important Safety Instructions ..........ccceeeeee Important Information on Safety Instructions .. Safety Symbols and Labels ................ cece General Safety Precautions .................cccccee Product Specifications ............cccccceceeeeeeeeeeeeeees Product DIMENSIONS ..........ccccccccceseseeeeseeeeeeeeeees Preparing for Installation..............cccceeeceeee Electrical Specifications 0.0.0... ccceeneeeeee Water Supply Specifications .............cceees Preparing the Location ....
Important Safety Instructions Important Information About Safety Symbols and Labels Safety Instructions DANGER The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand. See Customer Service Information.
Important Safety Instructions General Safety Precautions WARNING - To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING Use this dishwasher only.for its intended purpose as outlined in the use and care manual. It is not intended for. commercial use. Read the use and care manual completely before use. Do.
Product Specifications Product Dimensions <—— 24” (61.0 cm) Product tolerances: +1/16” (41.6 mm) >} Vv Depth with door open ~n—— 49 3/4” (126.4 cm) Depth with door closed ht 23 3/4” (60.3 cm)* TTI Ge Cc Loe] _|*~ Drain hose I< Front ~ 34 3/8” (87.4 cm) to 36 1/2” (92.7 cm) Depth dimensions allow Side for hose on back of unit —5 1/4” (13.5 cm) to 7 1/4” (18.5 cm) ay ~<— 2” (50.0 cm) Shipping weight: 108 Ibs. (49 Kg) * 23 1/2” (59.
Preparing for Installation WARNING Grounding Observe.all.governing codes and ordinances. during planning and insiallation. Contact your local building departmeni for further information. Electrical Specifications WARNING Electrical‘and grounding connections must comply with the applicable portions of the national-electrical code and/or other local electrical codes. Instructions for a Permanently-Connected Appliance This unit must be grounded to operate properly.
Preparing for Installation Preparing the Location WARNING Follow all cabinet dimensions shown to.insure. safe operation. All minimum product dimensions must be met or exceeded (see page 3). Dimensions shown provide the required clearances. ¢« Cutout tolerances: +1/16”, -0, (+1.6 mm, -0) The cabinet must enclose the dishwasher on the top, back and both sides.
Preparing for Installation Preparing the Drain CAUTION Keep the factory installed high loop drain hose in place to ensure proper:dishwasher-operation. Do not modify or move.the mounting bracket in any manner. If it is necessary to. lengthen the hose, install-an aftermarket drain extension kit, available at most home improvement stores. IMPORTANT: Should a drain hose longer than the one provided be required, use a hose extension approved for detergents and high temperature water.
Installation Instructions Verify the Package Contents Remove all styrofoam and plastic wrap from the dishwasher. Be sure to remove the toe kick and toe kick insulation from the top of the dishwasher packaging. With the assistance of at least one person, remove the dishwasher from the shipping pallet. Place the unit to the side of the cabinet opening. Remove the “O” ring attached to the water line in a plastic bag. Set it aside for use during the Water Line Connection.
Installation Installation Preparation WARNING Instructions 4. To make larger tension adjustments to the door springs, remove the back of the springs from the dishwasher by turning them outwards. Move them one hole farther back or forward, then make small adjustments as outlined in step 3 as necessary. « . Before working on wiring for any electrical appliance, be sure the electrical power has been turned off-at the breaker/fuse box.
Installation Level the Dishwasher Instructions 4. Open the door and pull the bottom rack out of the dishwasher. Check to make sure the dishwasher floor is level left to right using a level. Adjust the front legs as necessary. 5. Adjust the rear leg until the floor of the dishwasher is level front to back. CAUTION Alevel unit is very.important to proper operation. Be sure to level the unit front to back and side to side.
Installation Instructions Connecting the Electric Cable (Cont.} Installing the Unit in the Cabinet (Permanently Connected Appliance Only) 1. 4. If anonmetallic cable is being used, install a UL-listed strain relief bushing on the back of the dishwasher. 5. Connect the white wire on the cable to the “N’” terminal on the dishwasher terminal block as shown below. 6. Connect the black wire on the cable to the “L” terminal on the terminal block. 7.
Installation 4. Once the dishwasher sure all slack is pulled water supply line and sure none of them are is in place check to make out of the power cable, drain hose. Check to make pinched or kinked. Instructions 3. Connect the drain hose to the air gap or directly to the waste tee or disposer above the sink trap as shown in one of the examples on page 6. 4. Tighten the holding clamp. NOTE: Do not attach the mounting screws until after Verifying Operation.
Installation 4. Check for leaks under the dishwasher and under the sink. If any leaks are found, immediately push the START/STOP button and disconnect power. If there are leaks under the sink, check the water supply and drain connections. Reconnect power and restart the cycle. If the leak is elsewhere, and a hose extension is installed, check for a loose connection.
Installation . Attach Ng B rac kets ‘4° the Anti-+ti p Instructions 5. Cover the screw holes on the sides with the supplied plastic plugs. Push in the plugs diagonally to fit them in place. 6. Replace the top rack. CAUTION Make sure to anchor one anti-tip bracket on each side of the dishwasher. 1. The anti-tip brackets protect against possible tipping caused by heavy bottom rack loads on the door. Use only the stainless steel screws provided with the machine. 2. Open the door rack out.
Installation 5. Hang the toe kick on the brackets as shown. Check to make sure that the toe kick is even with the kitchen cabinet toe kick. If necessary, remove the toe kick and readjust the brackets. TOOT Installation Checklist WARNING «-.To ensure a safe and proper installation, the following checklist should be completed by ihe installer.to-ensure that no part of the installation has been overlooked and the unit is working properly. «Proper. installation is the responsibility of the homeowner.
dacor 15
16 dacor.
cdacor Item No., 80 889 19 Rev. 04 The Life of the Kitchen® Dacor e 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 Phone: (800) 793-0093 e Fax: (626) 403-3130 e www.Dacor.