Installation Instructions Modernist Built-In Electric Wall Oven DOB30M977 Part No.
Contents Before you begin... 3 Important 3 3 If You Need Help...
Before you begin... Important Installer • • • Design/accessories vary with the model. For safety and to minimize problems, read this manual thoroughly before starting the installation. Leave this manual with the user. Write the oven’s model/serial numbers in this manual for service/ maintenance reference. User • Keep this manual for personal and professional reference. Customer-service info If You Need Help...
Important safety instructions Related equipment safety Remove all tape and packaging before using the oven, and dispose of the packaging. Never let children play with packaging material. Do not modify the oven (e.g., do not remove panels, wire covers, or screws). Transport Oven (side) Pallet To avoid damaging the oven vent, use the transport method shown at left. Lift/support the oven bottom from either side, and move it to the installation site.
Important safety instructions • • • • • WARNING Follow the information in this manual precisely to avoid fire or electrical shock that may cause property damage, personal injury, or death. Ensure the oven is properly installed and grounded by a qualified technician. New branch-circuit installations (1996 NEC), mobile homes, RVs, or installations where local codes prohibit grounding through the neutral conductor, require 4-wire branch-circuit connection.
Installation requirements Location requirements IMPORTANT: Observe all governing ordinances. • • • • • Specified cutout dimensions are minimums and must be used. The cabinet recess must completely enclose all but the face of the oven. A grounded electrical supply is required. (See Electrical Requirements.) Put the electrical-supply junction box at most 3” (7.6 cm) below the support platform. Drill a 1” (2.5 cm) min.
Installation Materials Provided items 6 screws (M4 L16) (4 needed for installation, 2 extra) Install Handle (only for double oven) Needed Items Junction Box Wire Nuts /4” Conduit Connector Phillips Screwdriver 3 Drill English 7
Installation requirements Single ovens—Product Dimensions 13⁄8” (33 mm) 31⁄2” (89 mm) 287⁄8” (731 mm) 271⁄4” (691 mm) 297⁄8” (757 mm) 231⁄8” (587 mm) Front Side 471⁄4” (1200 mm) Conduit length 281/2” (724 mm) Top 8 English
Standard cabinet dimensions • Dimensions are minimums (except electrical supply location E) • Allow at least 22” between the open oven door and opposing cabinetry, walls, etc. • Leave at least 1” clearance under oven and 1-3/8 in. from cutout opening to cabinet above or countertop. • (Flush-mount only) Leave at least 2 1/2” unobstructed space below oven. 231⁄2” (597 mm) Top 13/8” (34.9 mm) Max. 91⁄2" (241 mm) 271/4” (692 mm) Side 283/4” (730.25 mm) Min.
Installation requirements Flush-cabinet dimensions • Dimensions are minimums (except electrical supply location E) • Allow at least 22” between the open oven door and opposing cabinetry, walls, etc. • Leave at least 1” clearance under oven and 1-3/8 in. from cutout opening to cabinet above or countertop. • (Flush-mount only) Leave at least 2 1/2” unobstructed space below oven. 231⁄2” (597 mm) 247⁄8” (630 mm) 13⁄8” (33 mm) Top Max. 91⁄2” (241 mm) 291/8” (739.77 mm) 301⁄4” (767 mm) 283/4” (730.
Double ovens—Product dimensions 13⁄8” (33 mm) 511⁄2” (1307 mm) 297⁄8” (757 mm) Front 31⁄2” (89 mm) 50” (1267 mm) 231⁄8” (587 mm) Side 67” (1700 mm) Conduit length 281/2” (724 mm) Top English 11
Standard cabinet dimensions • Dimensions are minimums (except electrical supply location E) • Allow at least 22” between the open oven door and opposing cabinetry, walls, etc. • Leave at least 1” clearance under oven and 1-3/8 in. from cutout opening to cabinet above or countertop. • (Flush-mount only) Leave at least 2 1/2” unobstructed space below oven. 231⁄2” (597 mm) Top 11/4” (31.75 mm) Max. 91⁄2” (241 mm) 283/4” 501/4” (1276 mm) (730.3 mm) 12” (305 mm) Side Front Min.
Installation requirements Flush-cabinet dimensions • Dimensions are minimums (except electrical supply location E) • Allow at least 22” between the open oven door and opposing cabinetry, walls, etc. • Leave at least 1” clearance under oven and 1-3/8 in. from cutout opening to cabinet above or countertop. • (Flush-mount only) Leave at least 2 1/2” unobstructed space below oven. 231⁄2” (597 mm) 247⁄8” (630 mm) Top 13⁄8” (33 mm) Max. 91⁄2” (241 mm) 51 3/4” (1314.5 mm) 301⁄4” (767 mm) 283/4” (730.
If codes permit and a separate ground wire is used, a qualified electrician should verify that the ground path and wire gauge comply with local codes. Check with a qualified electrician if you are unsure of the oven's grounding status. This oven must connect to a grounded-metal, permanent wiring system. Verify that the electrical connection and wire size are adequate and comply with the Nat'l Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.
Installation instructions Preparing to install the oven WARNING Excessive Weight Hazard To avoid personal injury and property damage, use two or more people to move the oven. 1. Decide the oven's final location. Avoid drilling/cutting household wiring/plumbing. 2. To avoid floor damage, set the oven on a cardboard sheet. (Do not lift by the door handle or any part of the front frame.) 3. Reduce the oven's weight to ease installation: a. Remove packing material and tape from the oven. b.
1. Carefully pull out the wire to reveal the connector. 2. Uncouple the connector. 1. 2. Open the oven door fully flat. Find the door hinge locks in both corners of the door, and flip them down to the unlocked position (see left) so the door can be removed. 3. Partially close the door to engage the door hinge locks. (The door stops at this point.) Removing the oven door(s) Locked Unlocked 4. Grasp each side of the door, and pull it away from the oven.
Installation instructions Replacing the oven door(s) CAUTION If needed, get help lifting the door into the hinge slots. Do not lift the door by the handle. 1. Slot Grasping each side at the midpoint, lift the door, and face the oven. 2. With the door at a 45° angle, align the hinges with the slots in the lower front of the oven. 3. Slowly insert the hinges into the slots. (You will know the hinges are engaged when you feel the door drop slightly.) 4. Open the oven door fully flat.
Electrical connection WARNING Electrical Shock Hazard • • • • Disconnect power before servicing. Use 8-gauge solid copper wire. Ground the oven. Failure to follow these instructions can result in fire, electrical shock, or death. This oven is manufactured with a neutral (white) power-supply wire and a cabinetconnected ground (green or bare) wire twisted together. 1. 2. UL-listed or CSAapproved conduit connector 3. 4. 5. 6. 7. Disconnect power.
Installation instructions 4-Wire Cable from Home Power Supply IMPORTANT: Use the 4-wire cable from home power supply in: • the US where local codes do not allow grounding through neutral • New Branch circuit installations (1996 NEC) • mobile homes and recreational vehicles • new construction • Canada. A B E F G H C I D A. B. C. D. E. F. G. H. I.
3-Wire Cable from Home Power Supply - U.S. Only IMPORTANT: Use the 3-wire cable from home power supply where local codes permit a 3-wire connection. NOTE: Connect all wires with UL-listed wire connectors (H). A B C G H D E I F A. B. C. D. E. F. G. H. I.
Installing the oven 1. Using 2 or more people, lift the oven partially into the cabinet cutout. Hang the install handle on the side of the oven. (See left.) NOTE Install Handle Before the next step, remove the install handle; keep it for future use. 2. Push against the oven's front frame until the back of the frame contacts the cabinet face or cleat*. *Flush installation WARNING When inserting the oven, take care not to damage the barrier beneath the oven. Barrier 3. 4. 5.
Self-diagnosis 1. 2. 3. After connecting the power, verify that the display works properly. Remove all accessories from the oven chamber. You cannot proceed with self-diagnosis if the oven cavity is hot or the door is open.(In this case, Hot or door appears on the display.) 4. To start self-diagnosis, press-hold both "hidden keys" for 5 seconds. • See the table below for each model's hidden keys. • Self-diagnosis takes 4-5 minutes.
Notes
DG68-00923A-00 Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745 ∙ Phone: (800) 793-0093 ∙ Fax: (626) 403-3130 ∙ www.dacor.
