Installation Instructions Modernist Pro Range DOP48M96DL*/DOP36M94DL* Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
Contents Contents Before you begin 5 Important About this manual Important note to the installer Important note to the consumer Important note to the servicer 5 6 6 6 6 Customer service information 7 Important safety instructions 8 Read all instructions before using this appliance Symbols used in this manual 9 9 Product specifications 21 What's in the box 21 Installation requirements 24 Pre-installation checklist General requirements Location requirements Gas requirements Special gas requi
To Our Valued Customer: Congratulations on your purchase of the very latest in Dacor® products! Our unique combination of features, style and performance make us The Life of the Kitchen™, and a great addition to your home. In order to familiarize yourself with the controls, functions and full potential of your new Dacor Appliance, read this use and care manual thoroughly, beginning with the Before you begin section.
WARNING: Failure to follow the instructions in this manual exactly may cause a fire or explosion, and, consequently, property damage, personal injury, or death. • DO NOT keep or use gasoline or other flammable products near this appliance. • IF YOU SMELL GAS: - DO NOT light any appliances. - DO NOT touch any electrical switches. - DO NOT use any phone in your building. - Immediately call your gas supplier from a neighbor's phone, and follow the supplier's instructions.
Before you begin Important Installer • • Contents To promote safety and minimize problems, read this manual thoroughly before starting the installation. Leave this manual with the user. Write the appliance’s model/serial numbers in this manual for service/ maintenance reference. User • The overall design and/or accessories may • differ with the model. Keep this manual for personal reference and for that of inspectors, service personnel, etc.
Before you begin About this manual READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. Important note to the installer • Before you begin • • • • • • Read all instructions contained in these installation instructions before installing the cooktop. Remove all packing materials from the cooktop compartments before connecting the electric and gas supply to the cooktop. Observe all governing codes and ordinances. Be sure to leave these instructions with the consumer.
Customer service information If you have questions or problems with installation, contact your Dacor dealer or the Dacor Customer Service Team. For repairs to Dacor appliances under warranty call the Dacor Distinctive Service line. Whenever you call, have the model and serial number of the appliance ready. The serial number can be found on the inner side of door trim. Dacor Customer Service Team Phone: (800) 793-0093 ex. 2813 (U.S.A. and Canada) Monday — Friday 6:00 a.m. to 5:00 p.m.
Important safety instructions ANTI-TIP DEVICE WARNING ALL RANGES CAN TIP, RESULTING IN PERSONAL INJURY. TIPPING RANGES CAN CAUSE BURNS FROM SPILLS, PERSONAL INJURY, AND/OR DEATH. INSTALL AND CHECK THE ANTI-TIP BRACKET FOLLOWING THE INSTRUCTIONS AND TEMPLATE SUPPLIED WITH THE BRACKET. Important safety instructions • To prevent accidental tipping of the range, attach an approved anti-tip device to the floor. (See Installing the Anti-Tip Device in the Installation Instructions.
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE • • Electrical and gas equipment with moving parts can be dangerous. The important safety instructions in this manual are intended to minimize the risk of property damage, personal injury, and death. Be sure to read them. Keep this manual in a handy place so you can refer to it as needed. Symbols used in this manual WARNING Hazards or unsafe practices that may result in severe personal injury or death.
Important safety instructions State of California Proposition 65 Warning (US only) WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Gas appliances can cause low-level exposure to Proposition 65 listed substances (including benzene, carbon monoxide, formaldehyde, and soot) resulting from the incomplete combustion of LP or natural gas.
• • • • • • • • • Do not use the product as a space heater. This product is to be used for cooking purposes only. Do not use oven cleaners or oven liners in or around any part of the oven. Use only dry pot holders. Do not use the product to heat unopened food containers. Do not strike the oven glass. When disposing of the range, cut off the power cord and remove the door. Unplug the product before service/maintenance. Make sure all meat and poultry is cooked thoroughly.
Important safety instructions Fire safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • Important safety instructions • • • Do not store/place/use combustible materials (e.g., paper, plastic, pot holders, linens, gasoline, alcohol) near the product. Do not wear loose fitting or hanging garments while using the product. To avoid grease buildup, regularly clean the vents.
Gas safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: If you smell gas: • • • • • • • • Close the valve and do not use the product. Do not light a match, candle, or cigarette. Do not turn on any gas or electric appliances. Do not touch any electrical switch or plug in a power cord. Do not use any phone in your building. Evacuate everyone from the building. Immediately call your gas supplier from a neighbor’s phone.
Important safety instructions Electrical and grounding safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • • • • Important safety instructions • • • • • Plug into a grounded 3-prong outlet. Do not remove the ground prong. Do not use an adapter or an extension cord. Do not use a damaged power plug, power cord, or loose power outlet. Do not modify the power plug, cord, or outlet. Do not put a fuse in a neutral or ground circuit.
Installation safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • • • • • Do not try to service/modify/replace the product or any part of it unless specifically recommended in this manual. All other service should be performed by a qualified technician. Use only new, flexible connectors when installing the product. Make sure the anti-tip device is properly installed. (See the Installation Instructions for details.
Important safety instructions Location safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • Important safety instructions • • • • • • This range is for indoor household use only. Do not install the range outdoors or anywhere that it will be exposed to weather/water or wind/ strong drafts. Select a level, well-constructed floor that can support the range’s weight.
Cooktop safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • • • • • • • • • • • • • • Always use the LITE position to ignite a burner, then make sure the burner has ignited. If ignition fails, turn the knob to OFF, and wait a few minutes for the gas to dissipate. When you set a burner to simmer, do not turn the knob quickly. Make sure the flame stays on. Do not place any objects other than cookware on the cooktop.
Important safety instructions • • • • • When frying, always heat the oil slowly, and monitor the oil as it heats. When frying foods at high heat, monitor the oil throughout the cooking process. If combining fats or oils for frying, mix them together before heating. Use a deep-fry thermometer when possible to avoid heating the oil beyond its smoke point. (Know the smoke point of the oil you are using.) Always use a minimum amount of oil for any type of frying.
• • • • • • • Keep the oven free from grease buildup. When repositioning the oven racks, make sure the oven is completely cool. Do not leave plastic items inside the oven. To avoid damaging the burner control knobs or oven control, always bake and/or broil with the oven door closed. Do not broil meat too close to the broil element. Trim excess fat from meat before cooking. When using cooking or roasting bags in the oven, follow the manufacturer’s directions.
Important safety instructions Self-cleaning oven safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • Important safety instructions • • • • • • • • The self-cleaning feature operates the oven at temperatures high enough to burn away food soils in the oven. The range is extremely hot during a self-cleaning cycle. Do not touch any surfaces of the range during a selfcleaning cycle.
Product specifications What's in the box Parts list - DOP48M96DL* Burner heads (6) and Burner caps (7) Griddle (1) Convection filter (3) Temp. Probe (2) Glide racks (2) WOK ring (1) Anti-tip bracket (1) Wire rack (1) Small rack (1)* Steam tray (2)* Half steam tray (2)* Product Specifications Grates (3) NOTE • • The range is supplied with two different types of burner caps (brass and porcelain) to suit the customer’s preference. Parts with asterisk (*) is only for Steam oven.
Product Specifications Parts list - DOP36M94DL* Product Specifications Grates (2) Burner heads (4) and Burner caps (5) Wire rack (1) Convection filter (2) Temp. Probe (1) Glide racks (2) Griddle (1) WOK ring (1) Anti-tip bracket (1) The range is supplied with two different types of burner caps (brass and porcelain) to suit the customer’s preference. 22 English Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
Parts needed Gas line shut-off valve Flexible metal appliance connector ½ in (ID) x 5 ft Flare union adapter ¾ in (NPT) x ½ in (ID) 135-degree elbow (optional) Lag bolt or ½-in (OD) sleeve anchor Flare union adapter ½ in (NPT) x ½ in (ID) Tools needed Phillips screwdriver Open-end or adjustable wrench Pipe wrench (2) Nut driver Pencil and ruler Level Pipe joint compound Utility knife Soapy water solution Product Specifications Flat-blade screwdriver English 23 Install_NY9900M_PRORANGE_DO
Installation requirements Pre-installation checklist 1. Before preparing the opening in the countertop or cabinet, verify that there will be no conflict between the range and anything in the cabinet below. 2. Remove packing materials, grate boxes, regulator with literature, and literature package from the range, verify that all items are present before beginning the installation.
Minimum dimensions WARNING If overhead cabinets are provided, a range hood should also be provided that projects horizontally a minimum of 5 in (12.7 cm) beyond the front of the cabinets. This will dissipate any heat buildup in the overhead cabinets to prevent death, personal injury, and/or fire hazard. The ventilating hood must be constructed of sheet metal not less then 0.0122" thick.
Installation requirements Product dimensions NOTE Product tolerances: ±1/16” (±1.6 mm) 48” (121.9 cm) 28 1/8” (71.4 cm) 27 1/2” (69.9 cm) 26” (66.0 cm) 23 15/16” (60.8 cm) Front of open door Front of handle Front edge of bull nose Front panel Rear of oven door 1 1/4” (3.2 cm) X* * The optional backguard is available in two heights; 3 and 9 inches high. 15/16” (2.4 cm) to cooking surface (top of grates) from top of trim Finished side panel Width: 36 1/8" (91.8 cm) DOP36M94DL* - 35 7/8” (91.
Cabinet dimensions • • • All maximum and minimum dimensions and clearances shown in the diagrams below must be maintained for safe operation. Check the location where the range is to be installed. It should be placed away from drafts that may be caused by doors, windows and heating and air conditioning outlets. To reduce the risk of fire or personal injury from reaching over a hot appliance, avoid cabinet installations directly above the range.
Installation requirements 1 Vertical from range grate level to combustible overhead surface; if installing an overhead vent hood, also check hood specifications for minimum required clearances. 2 Cabinet/countertop depth is at discretion of customer but cabinet face MUST NOT protrude further than rear of front panel, see product dimensions. 3 Consult local code for exact location requirements. 4 Vertical from grate level to combustible surface.
DOP36M96DL* 28.4 cm (11 3/16") Gas Inlet Back of range 61.6 cm (24 1/4") Shown with electrical access cover removed 16.8 cm (6 5/8") 22.5 cm (8 7/8") 1 Measurement with appliance legs adjusted to lowest height. Installation requirements The hole size for the electrical wiring may be increased to 1 1/8” (2.9 cm) by removing the conduit bracket in the bottom of the range electrical box. 2 English 29 Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
Installation requirements Gas and Electrical Service • • • • • • The shaded area shown below denotes the location of the gas inlet and the electrical junction box/receptacle. This is the recommended location. For replacement purposes, the location of the existing utilities may be utilized provided they do not interfere with the sides or rear of the range. Check local building codes for permissible gas valve locations.
Gas requirements Provide adequate gas supply. The installation of this appliance must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54. The cooktop of this range is designed to operate at a manifold pressure of 5 in (13 cm) of water column on natural gas. Be certain that the appliance being installed is correct for the gas service provided (natural gas).
Installation requirements The pressure regulator located at the inlet of the cooktop manifold must remain in the supply line regardless of whether natural or LP gas is being used. NOTE • • • • The rangetop has its own regulator. Use only the provided regulator, which must be installed in the gas line that runs from the cooktop gas inlet to the gas shut-off valve. An external manual shut-off valve must be installed between the gas inlet and the cooktop for turning on/off gas to the appliance.
Electrical requirements • Failure to follow these instructions can result in death, fire, or electrical shock. • It is the owner’s responsibility to make sure that the electrical service meets electrical requirements and that he electrical outlet has been properly installed by a licensed electrician. To reduce the risk of fire, electric shock, or personal injury: WARNING • All range • • • • • • • KW Rating (240 V) Recommended Circuit Size (Dedicated) 7.3 KW - 9.6 KW 40 Amp 9.7 KW - 12.
Installation instructions Preparing for installation WARNING • • If the gas or electric service provided does not meet the product specifications, do not proceed with the installation. Call the dealer, the gas supplier or a licensed electrician. Before installing the range, you must locate and secure the anti-tip bracket to the floor. NOTE Within the Commonwealth of Massachusetts, this appliance must be installed by a licensed plumber or gas fitter.
Installing the Anti-Tip Bracket on the Floor WARNING To perform its intended function, the anti-tip bracket must be attached as instructed to the concrete slab or wood sub-floor below any floor coverings (including cement board) on top. Do not attach the anti-tip bracket directly to floor coverings such as ceramic/asphalt tile or linoleum.
Installation instructions Attaching the bracket to a concrete floor: • • Drill four (4) 3/8” diameter countersink holes through any existing floor covering down to the concrete slab below. Drill the 4 holes for the anchors 1 1/4” (3.2 cm) deep into the concrete slab using a 3/16” masonry bit. This hole length is longer than the anchor, but is required for proper installation. Clear the holes of dust and any other material.
SCREW SIZE TABLE Sub-Floor Type/Floor Covering Thickness Screw Size Concrete or wood subfloor, no floor covering over top #8 x 1 * Concrete or wood subfloor, floor covering up to 1/4” thick #8 x 1 * Concrete or wood subfloor, floor covering over 1/4” and up to 1/2” thick #8 x 1 1/4 * Wood sub-floor, floor covering over 1/2” and up to 1 3/16” thick #12 x 1 3/4 * Concrete under floor covering over 1/2” thick Must be purchased separately ** Wood sub-floor, floor covering over 1 3/16” thick Must be
Installation instructions Installing the Anti-Tip Bracket on the Wall 1. Determine the suitability of wall mounting the anti-tip bracket. To use the wall mount option, the range front panel must not be more than 26 1/2” (67.3 cm) from the wall and the bracket screws must be able to thread into the base plate inside the wall behind.
#12 x 1 3/4” screw, 4 places This hole lines up with bracket center line Back wall Range center line C Bracket center line C C Range front panel Top View - Location of Wall Mounted Anti-Tip Bracket ANTI-TIP BRACKET PLACEMENT DOP36M94DL* DOP48M96DL* C 14 1/8” (35.9 cm) 3 1/2” (8.9 cm) Installation instructions Dimension English 39 Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
Installation instructions Removing the Oven Door WARNING • • Do not attempt to disengage the hinge catches with the door(s) removed from the range. The hinge springs could release causing personal injury. Do not lift or carry the oven door(s) by the handle. NOTE When installing a backguard, always install it before sliding the range into place. See page 34. To make the range easier to move, remove the door(s) to reduce weight. Catch Retaining arm 1. Open the door to its fully opened position. 2.
Electrical connection CAUTION For personal safety, do not use an extension cord with this appliance. Remove house fuse or open circuit breaker before beginning installation. This appliance must be supplied with the proper voltage and frequency, and connected to an individual properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as specified on the rating plate. The rating plate is located on the inner side of each side panels covering oven door.
Installation instructions Effective January 1, 1996, the National Electrical Code requires that new construction (not existing) utilize a 4-conductor connection to an electric range. When installing an electric range in new construction, follow Steps 2 and 3 for 4-wire connection. You must use a 3-wire or 4-wire, single-phase A.C. 240 Volt, 60 hertz electrical system. If the electrical service provided does not meet the above specifications, have a licensed electrician install an approved outlet.
Accessing the power cord connection Remove the rear access cover and loosen the screw with a screwdriver. The terminal block will then be accessible.
Installation instructions Installing the power cord Conduit connection plate Power cord Strain relief For power cord installations, hook the strain relief over the power cord hole (1⅜") located below the rear of the drawer body. Insert the power cord through the strain relief and tighten the device. • You must install the power cord with a strain relief. • Attach the strain relief to the 1⅜" opening in conduit connection plate.
Installing a 4-wire power cord WARNING The neutral wire of the supply circuit must be connected to the neutral terminal located in the lower center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block. The grounding lead (Green) must be connected to the frame of the range with the ground plate and the ground screw. 1. Remove the 3 lower terminal screws from the terminal block. Remove the ground screw and ground plate and retain them.
Installation instructions Installing the conduit Remove the conduit connection plate from the rear of the drawer body and rotate it as shown below. The conduit hole (1⅛") must be used. 1⅛" 1⅜" 1⅜" 1⅛" 1. Prepare the conduit cord shown in Figure 1. 2. Install the conduit cord as shown in Figure 2.
Installing a 3-wire conduit • Aluminum building wire may be used but it must be rated for the correct amperage and voltage. Connect wires according to Step 4 depending on the number of wires. • Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes. Ground strap Neutral terminal Black Black White Red White Red Wire tips 1. Loosen the 3 lower terminal screws from the terminal block. 2.
Installation instructions Installing a 4-wire conduit • Aluminum building wire may be used but it must be rated for the correct amperage and voltage. Connect wires according to this Step 4 depending on the number of wires. • Wire used, location and enclosure of splices, etc., must conform to good wiring practices and local codes. 1. Loosen the 3 lower terminal screws from the terminal block. Remove the ground screw and ground plate and retain them. Ground strap 2. Cut and discard the ground strap.
Gas connection WARNING • • • • • • • Make sure the gas supply valve is off and that the power to the range is turned off at the circuit breaker or fuse box prior to connecting the gas line. Do not apply excessive pressure when tightening gas connections and fittings. Do not use Teflon tape or plumber’s putty on gas flex line connections. The maximum gas supply pressure to the regulator must never exceed 1/2 pound per square inch (psi) or 3.5 kPa.
Installation instructions Before sliding the range into the cabinet: 1. Make sure the gas supply valve is in the off position and that power to the range is off. 2. Connect a flexible gas supply line to the gas shut-off valve previously installed on the stub out. The gas line needs to be long enough to allow the range to be pulled out for service. 3. Slide the gas line up through the access holes in the chassis and up to the regulator.
Final installation 1. Peel the protective coating off of the range, including the door. * Distance to floor: 4 1/16” to 5 5/16” Rear leg Back of range 1 1/4” * up down Anti-Tip Foot (location varies) 2. Measure from the floor to the countertop. Adjust the leveling legs as required to position the trim around the cooktop even with or above the countertop. 3. Locate the anti-tip foot on the back of the range and lower (turn) it until it is 1/16” (2 mm) off the floor. 4.
Installation instructions Re-installing the Oven Door(s) WARNING To avoid personal injury or damage to the door from it falling off its hinges: • Make sure that the notch on the bottom of each hinge rests on top of the lower lip of each hinge receptacle before attempting to open the oven door. • Rotate the hinge locks toward the front of the range immediately after installation of the door. 1. Grasp the oven door on opposite sides and hold it at a 15° angle from the front of the oven.
Door adjustment (DOP48M96DL* Only) After re-installing the oven doors, make sure the oven doors to be parallel and flush. There are 3 bolts around the Steam oven, one on the right-upper side of the steam oven, and two under the each door hinge. The upper bolt helps adjusting the door back and forth. The lower two bolts help adjusting the door up and down. To adjust door up and down 1. Remove door and remove 2 screws on door hinge latch. 2. Turn the bolt under each door hinge latch. 3.
Installation instructions Installing the knobs for surface burners WARNING Installing the range knobs in the wrong position may result in damage to the griddle included with the range. The knobs for the center burners are marked with the maximum griddle settings. NOTE When installing the knobs, align the “D” shaped opening on the back of the knob with the end of the valve shaft. Carefully push the knob on until it stops. There are two (2) different types of knobs supplied with the range.
Cooktop assembly Assembling the rangetop burners CAUTION • • • Do not operate the rangetop burners without all burner parts in place. Do not push in any rangetop controls while removing the burner; a slight electrical shock might result, perhaps causing you to knock over hot cookware. Do not risk electric shock by removing the top or touching the electrode of any burner while another burner is on. 1. Place the burner heads on the burner bases as shown at left.
Installation instructions Dual Burner head / caps 1. Orient the burner head so the opening for the electrode aligns with the electrode. 2. Install the burner head so the electrode passes through its opening in the head. Ensure the burner head lies flat on the stove top. 3. Match the burner caps to the burners by size, then install the caps on the heads. Installation instructions 56 English Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
Round Burner head / caps 1. Put the burner heads on the burner bases as shown at left. The bottom of the head fits within the burner base. 2. Turn the head until it drops into place. Twist the head back and forth slightly to ensure it is properly seated. 3. Put the burner caps (brass or porcelain) atop the burner heads. The ridge around the bottom edge of the cap fits around the top of the burner head. CAUTION Ensure all burner components (heads and caps) rest flat and snugly in place.
Installation instructions SimmerSear Burner Assembly (18K BTU Burner) Burner head Locating tab 1. Put the burner heads in place as shown below. The locating tab on the burner head goes in the keyed hole as shown. Burner base Keyed hole Burner ring Tabs Slots Ridge on bottom of burner cap 2. Put the burner rings on the burner heads as shown below. Match the tabs on the bottom of the ring to the slots on the burner head. Twist each ring back and forth slightly to make sure it is properly seated.
Installing the grates NOTE For best results and longest life, install the grates as instructed below. When installed properly, the openings in the grates are centered over the burners. The grates occupy specific positions on the rangetop. For maximum stability and safe operation, these grates should only be used in their proper positions. The back of the right grate is notched to help orient the grates correctly. (See the graphic below.) To correctly position the grates: 1.
Installation instructions Verifying proper operation Before operating the range, read the accompanying use and care manual completely. It contains Important safety, service and warranty information. 1. Before beginning the test procedure, ensure that all cooktop control valves are in the OFF position, and all burner rings, burner caps, and grates are properly positioned on the cooktop frame. 2. Turn on the gas supply at the shut-off valve. Check for gas leaks. 3.
If the range does not operate properly, follow these troubleshooting steps: 1. Verify that power and gas are supplied to the range. 2. Check the electrical connections and gas supply to ensure that the installation has been completed correctly. 3. Repeat the above bake test or burner ignition test. 4. If the appliance still does not work, contact Dacor Distinctive Service at (800) 7930093 ex. 2822. Do not attempt to repair the appliance yourself. Have the model and serial numbers available when you call.
Installation instructions This page left blank intentionally Installation instructions 62 English Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
Removal and Re-installation Removing the Range for Service 1. Turn the gas supply valve to the off position. 2. Turn off power to the range at the circuit breaker panel or fuse box. 3. Pull the range out from the wall Reinstalling the Range After Service 1. Push the range into operating position, making sure the anti tip bracket is engaged (see page 51). 2. Turn on power to the range at the circuit breaker panel or fuse box. 3. Turn the gas supply valve to the on position.
Installation instructions Installation checklist WARNING • • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor range cannot be overemphasized.
MEMO Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
MEMO Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
Please visit www.Dacor.com to activate your warranty online. WARRANTY INFORMATION IMPORTANT: Your warranty will not begin until you activate it online or return this form to Dacor. If you have purchased more than one Dacor product, please return all forms in one envelope, or activate the warranty for each product online. cut here Please rest assured that under no conditions will Dacor sell your name or any of the information on this form for mailing list purposes.
DG68-00936A-00 Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745 ∙ Phone: (800) 793-0093 ∙ Fax: (626) 403-3130 ∙ www.dacor.com Install_NY9900M_PRORANGE_DOP48M96DLM_DA_DG68-00936A-00_EN+MES+CFR.
