Installation Instructions Distinctive ™ Series Cooktop Models: DRT304S, DRT366S THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS APPLIANCES. Part No. 106522 Rev.
Table of Contents Important Safety Instructions........................................... 1 Important Information About Safety Instructions............... 1 General Safety Precautions.............................................. 2 Installation Requirements................................................. 3 Electrical Requirements.................................................... 3 Gas Supply Requirements................................................ 3 Product Dimensions................................
Important Safety Instructions Important Information About Safety Instructions IMPORTANT: If you smell gas: • • Do not use or light any appliance. • Do not touch any electrical switch or use any electrical devices, including the telephone, in your building. • From a neighbor’s phone, immediately call the gas supplier. Follow the gas supplier’s instructions. • If you cannot contact the gas supplier, call the fire department.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING • Do not climb on any part of the appliance. • To avoid a fire hazard, do not hang flammable or heat sensitive objects over the cooktop. • Do not leave children alone or unattended in the area around the cooktop.
Installation Requirements warning • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • To prevent an electric shock hazard, the power supply must meet the specifications stated below. The electrical and gas supply data on this page is for reference only. If the requirements below do not agree with the product data label, use the data on the product data label.
Installation Requirements Cabinet and Countertop Layout • To reduce the risk of personal injury and to reduce accumulated smoke in the room, Dacor strongly recommends installing a range hood. A hood should project forward a minimum of five (5) inches beyond the face of the cabinets. • The installation must allow access to the underside of the cooktop for service and inspection purposes, including the ability to turn off the cooktop gas supply valve and electrical outlet.
Installation Requirements Cabinet/Cutout Dimensions 10” (25.4 cm) to combustible side wall min. both sides Cabinet tolerances +1/16” (+1.6 mm), -0 unless otherwise noted. 1 1/2” (3.8 cm) typical countertop thickness 1/2” (1.3 cm) overhang, both sides B 7 3/4” (19.7 cm) Recommended gas and electrical service location, consult local code Cooktop platform 1” (2.5 cm) min. thickness 36” (91.4 cm) typical Cabinet/Countertop Dimensions - Front View 13” (33.0 cm) max.
Installation Requirements Cabinet/Countertop Dimensions (cont.) Cutout tolerances +1/16” -0 (+1.6 mm, 0) unless otherwise noted. Gas and electrical connections at right rear section of chassis Gas connection and power cord may be routed through bottom or back of chassis Increase countertop and overhang additional 2 1/2” (6.4 cm) min. for combustible rear wall above countertop Non-combustible rear wall, rear of mounting platform 10” (25.4 cm) min.
Installation Requirements 3/8” (1.0 cm) min. countertop overhang 2 5/8” (6.7 cm) Non combustible rear wall recommended 10” (2.5 cm) min. to combustible wall above countertop, both sides F Open to below to allow for downdraft vent, gas and electrical connections E 1/2” (1.3 cm) countertop overhang 1” (2.5 cm) thick mounting platform min. Countertop 24 1/2” 15” (62.2 cm) (38.1 cm) Countertop 1/2” (1.3 cm) countertop overhang Hole 1/2” dia. (1.
Installation Instructions Cooktop Installation Unpack the Cooktop warning • If the gas and electric service provided does not meet the product specifications, do not proceed with the installation. Call the dealer, the gas supplier or a licensed electrician. • The cooktop is heavy. A minimum of two people are required to safely install it. Unpack the parts box and verify that all required components have been provided. If any item is missing or damaged, please contact your dealer immediately.
Installation Instructions Knob Installation Control Panel DRT304S 1. Attach the SimmerSear burner knobs A as shown below. The SimmerSear knobs have a wider space between the large flame icon and the simmer icon than the standard burner knobs. Align the “D-shaped” opening on the back of each knob with the end of the valve shaft. Carefully push each knob on until it stops. B A B 2. Attach the remaining knobs which operate the standard burners B .
Installation Instructions Burner Component Installation warning • Never attempt to operate the cooktop with any of the burner parts removed. • Do not attempt to adjust the burner air mixture settings. All adjustments are preset at the factory. Remove the burner parts and grates from their shipping packages. SimmerSear Burner Assembly Standard Burner Assembly 1. Install the SimmerSear burner ring(s) on top of the SimmerSear burner base(s).
Installation Instructions Verifying Proper Operation NOTE: If the cooktop does not operate properly, follow these troubleshooting steps: warning • • Make sure that power to the electrical outlet is turned off at the circuit breaker or fuse box and that the gas is turned off at the gas supply valve before proceeding. The cooktop must be properly grounded at all times when electrical power is applied. Prior to operating the cooktop, read the accompanying use and care manual carefully. 1.
Wiring Diagrams W W FL B B FL INDICATOR LIGHT Single Point Spark Module RL RL INDICATOR LIGHT WIRING DIAGRAM DRT304 O VERIFY PROPER OPERATION AFTER SERVICING RL IGNITOR FL IGNITOR O Single Point Spark Module W B W B RR IGNITOR B FR IGNITOR B O O RR INDICATOR LIGHT W RR B B Single Point Spark Module FR INDICATOR LIGHT W FR Single Point Spark Module B W 120V, 60Hz, 0.
O O RL B FL B Single Point Spark Module FL IGNITOR W FL INDICATOR LIGHT Single Point Spark Module RL IGNITOR W RL INDICATOR LIGHT VERIFY PROPER OPERATION AFTER SERVICING WIRING DIAGRAM DRT366 B W B W B B O O B FC B Single Point Spark Module FC IGNITOR W FC INDICATOR LIGHT Single Point Spark Module RC RC IGNITOR W RC INDICATOR LIGHT B W B W B B O O FR IGNITOR B FR Single Point Spark Module W B Single Point Spark Module RR FR INDICATOR LIGHT RR IGNITOR W
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.