Installation Instructions Distinctive ® Gas Cooktop Models DTCT304G, DTCT365G, DTCT466G Part No. 108856 Rev.
Table of Contents Important Safety Instructions........................................... 1 Important Information About Safety Instructions............... 1 General Safety Precautions.............................................. 2 Installation Specifications................................................. 3 Product Dimensions.......................................................... 3 Electrical Requirements.................................................... 4 Gas Supply Requirements....................
Important Safety Instructions Important Information About Safety Instructions The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand. See Customer Service Information.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING • Read the accompanying use and care manual completely before operating this appliance. • Keep packaging materials away from children. Plastic sheets and bags can cause suffocation. • If you receive a damaged product, immediately contact your dealer or builder.
Installation Specifications WARNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Product Dimensions All tolerances: ±1/16” unless otherwise noted. 1 5/8 in (4.1 cm) bottom of base to cooking surface 30 in (76.2 cm) Model DTCT304G 4 in (10.2 cm) chassis height 21 in (53.3 cm) 27 5/8 in * (70.2 cm) 19 1/2 in * (49.5 cm) * including raised embosses on sides of chassis Model DTCT365G 1 5/8 in (4.
Installation Specifications Electrical Requirements Gas Supply Requirements WARNING To prevent an electric shock hazard, the power supply must meet the specifications stated below. It is the owner’s responsibility to make sure that the electrical service meets electrical requirements and that the electrical outlet has been properly installed by a licensed electrician. • The cooktop is supplied with a factory installed, 40-inch, three-prong, grounding electrical plug.
Installation Specifications Cabinet and Countertop Layout WARNING • To reduce the risk of personal injury caused by reaching over a hot appliance, avoid locating cabinet storage space directly above the cooktop. • Failure to meet or exceed the maximum and minimum dimensions/clearances stated in these instructions may result in a fire hazard. • Follow the countertop manufacturer’s instructions regarding the minimum corner radius, use of heat reflective tape, reinforcement of corners, etc.
Installation Specifications Cutout Dimensions All tolerances: +1/16” -0” unless otherwise noted. IMPORTANT: Be careful to choose the correct cutout diagram on page 7. There are two cutout styles: a square cutout and a knotched cutout. Use the table below to determine the countertop cutout type and the dimensions for the installation. 1. Find your specific DTCT model that matches your specific configuration setup. 2. Choose the square or notched cutout type according to your configuration (see below). 3.
Installation Specifications All tolerances: +1/16” -0” unless otherwise noted. Countertop Cutout Dimensions Diagrams for “Cutout Type and Dimensions” Table on page 6 Square Cutout Side wall Rear wall Vertical combustible surface 4 1/4 in (10.8 cm) min. between mounting surface and combustibles below cooktop chassis C E 7 1/2 in (19.1 cm) min. to combustible side wall above countertop (on both sides of cooktop) D 1 7/8 in min. (4.8 cm) Notched Cutout Side wall Rear wall 4 1/4 in (10.8 cm) min.
Installation Specifications Cutout Dimensions All tolerances +1/16” -0”, unless otherwise noted. With ERV or PRV Series Downdraft (side view) 3/8 in min. (1.0 cm) required behind cutout for downdraft cap clearance Stiffener Countertop DTCT Series Cooktop Cabinet face 3/8 in min. (1.0 cm) behind downdraft chassis to clear stiffener ERV or PRV Series Downdraft: Check downdraft specifications to determine correct fit Floor With RV Series Downdraft (side view) Stiffener 5/8 in min. (1.
Installation Instructions Verifying Package Contents • Hold-down brackets (2) • Gas pressure regulator (1) • Grates: DTCT304G (2), DTCT365G (3) DTCT466G (3) • Burner sets: DTCT304G (4), DTCT365G (5), DTCT466G (6) • Stainless steel cleaner (1) Connecting the Gas Line WARNING If any parts are missing, see the Replacement Parts list on page 12 for ordering information. Installing the Cooktop WARNING • Verify that the power supply meets the specifications on page 4 before proceeding.
Installation Instructions Installing the Burner Assemblies Verifying the Correct Setup WARNING WARNING • Never attempt to operate the cooktop with any of the burner parts removed. • Do not attempt to adjust the burner air mixture settings. All adjustments are preset at the factory. 1. Remove the burner heads, burner rings, burner caps, and grates from their shipping packages. 2. Install the burners as shown.
Installation Instructions Verifying the Correct Setup • Once the burner lights, rotate the control knob from HIGH to LOW to adjust the flame height. • When the unit is installed correctly, the flame burns steadily and has a sharp, blue inner cone that varies in length proportional to the burner size. The flame will be reduced by the Smart Flame™ feature under the grate fingers to increase grate life.
Replacement Parts Ordering Parts DTCT466G Replacement parts can be easily obtained by contacting Dacor Customer Service. Dacor Customer Service Phone: (800) 793-0093 (U.S.A. and Canada) Monday — Friday 6:00 a.m. to 5:00 p.m.
Wiring Diagrams 120V, 60Hz POWER SUPPLY AFTER SERVICING VERIFY PROPER OPERATION WIRING DIAGRAM DTCT304G CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION.
Wiring Diagrams 120V, 60Hz POWER SUPPLY AFTER SERVICING VERIFY PROPER OPERATION 14 WIRING DIAGRAM DTCT365G CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION.
Wiring Diagrams 120V, 60Hz POWER SUPPLY AFTER SERVICING VERIFY PROPER OPERATION WIRING DIAGRAM DTCT466G CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION.
Notes 16
Notes 17
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.