Installation Manual Gas Cooktop DTG30P875N* DTG36P875N* Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. • DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. • WHAT TO DO IF YOU SMELL GAS: --DO NOT try to light any appliance. --DO NOT touch any electrical switch. --DO NOT use any phone in your building. --Immediately call your gas supplier from a neighbor’s phone.
Important safety information About this manual READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. • All electrical and gas equipment with moving parts can be dangerous. Please read the important safety instructions for this appliance in this manual. The instructions must be followed to minimize the risk of injury, death, or property damage. • Save this manual. Please Do Not Discard.
Important safety information California Proposition 65 Warning WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov Important safety information Commonwealth of Massachusetts • This product must be installed by a licensed plumber or gas fitter qualified or licensed by the State of Massachusetts. When using ball-type gas shut-off valves, you must use the T-handle type. Multiple flexible gas lines must not be connected in series.
Gas safety Electrical and grounding safety WARNING WARNING To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. • Close the valve and do not use the cooktop. • Do not light a match, candle, or cigarette. • Do not turn on any gas or electric appliances. • Do not touch any electrical switches or plug a power cord into an outlet. • Do not use any phone in your building. • Evacuate the room, building, or area of all occupants.
Important safety information Installation safety WARNING Important safety information To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. • Have your cooktop installed and properly grounded by a qualified installer, in accordance with the installation instructions. Any adjustment and service should be performed only by qualified gas cooktop installers or service technicians.
Location safety Cooktop safety WARNING WARNING To reduce the risk of fire, electric shock, personal injuries, and/or death, obey the following precautions. • This cooktop is for indoor, household use only. Do not install the cooktop in areas exposed to the weather and/or water. • Do not install the cooktop in a place which is exposed to a strong draft. • Make sure all burners are off when not in use. • Do not use aluminium foil to line the grates or any part of the cooktop.
Gas cooktop components Important safety information Gas cooktop components • Stand away from the cooktop while frying. • Always heat frying oils slowly, and watch as they heat. If you are frying foods at high heat, carefully watch during the cooking process. If a combination of fats or oils is to be used during frying, mix them together before heating. • Use a deep-fryer thermometer whenever possible. This prevents overheating the fryer beyond the smoking point.
Parts needed Gas line shut-off valve Flexible metal Flare union adapter Flare union adapter appliance connector ¾ in or ½ in (NPT) x ½ in (NPT) x ½ in ½ in (ID) x 5 ft ½ in (ID) (ID) Flat-blade screwdriver Phillips screwdriver Open-end or adjustable wrench Pipe wrench (2) ¼" Nut driver Pencil and ruler Level Pipe joint compound Utility knife Soapy water solution Pliers Saber saw 90-degree elbow (optional) Gas cooktop components 135-degree elbow (optional) Tools needed English 9 Install_D
Installation requirements Pre-installation checklist NOTE 1. When preparing cooktop opening, make sure the inside of the cabinet, and the cooktop do not interfere with each other. 2. Remove packing materials, grate boxes, regulator with literature, and literature package from the cooktop before beginning installation. Location requirements All horizontal clearances must be maintained for a minimum of 18” (457 mm) above the cooking surface. 7 /16” (11.1 mm) 39/16” (90.
Overall cooktop dimensions Installation dimensions with downdraft hood NOTE A • Make sure the clearance dimensions when you install the cooktop with downdraft hood. • The cooktop can be installed after detaching iQ Connect module. Please refer to the instruction how to detach iQ Connect module on page 15. 27/16” (62 mm) countertop to grate surface 21” (533 mm) B Model C A 30” (762 mm) 36” (914.4 mm) DTG30P875N* DTG36P875N* B 281/8” (715 mm) 3311/16” (855 mm) iQ Connect Module C 193/8” (492.
Installation requirements Single Oven Under counter Utility locations and dimensions 02 01 H A E 01 This cooktop can be installed above any single built-in oven. Refer to installation manual of oven. 02 Gas and Electrical Connections for Gas Cooktop Must be Located in an Adjacent Accessible Location to the Right. Front of unit Power cord 393/8” (100.0 cm) long F B 115/16” (5.0 cm) /8”-18 NPT male gas inlet 3 Size Min. 3 /4” (9.5 cm) A 11/4” (3.
The pressure regulator located at the inlet of the cooktop manifold must remain in the supply line regardless of whether natural or LP gas is being used. NOTE • The cooktop comes from the factory with a regulator in the shipping carton. Use only the regulator provided. The regulator must be installed in the gas line that runs from the cooktop gas inlet to the gas shut off valve.
Installation instructions Grounding • All cooktops must be grounded for personal safety. • The plug must be firmly plugged into a three-prong outlet that is properly installed and grounded in accordance with all local codes and ordinances. In the event of a malfunction or breakdown, grounding will decrease the risk of electrical shock by providing a path for the electric current. • Do not use a damaged power plug or loose wall outlet.
1. Locate electrical outlet and gas shut-off valve beneath cabinet. 2. Apply the foam tape around the edge of the cutout opening. Do not overlap the foam strips. • The foam strip helps avoid damage to the underside of the cooktop from debris and helps the cooktop sit flat on uneven counters. 3. Protect surface of cooktop • Place a towel or tablecloth onto the countertop. 4. With bottom side first, gently put the cooktop down.
Installation instructions Rubber iQ Connect module 1. Remove screws from all 5 burner cups and 4 screws from the cooktop frame. Remove the rubber protecting iQ Connect module. Pull out all knob dials and lift up to remove the frame cooktop. 2. Detach iQ Connect module from case burner. Disconnect wire connector from the PCB. 3. Install supplied cover in place of iQ Connect module. Cover 4. Insert the wire connector diagonally into the cover. Make sure it fits firmly. Top view 5.
– – – – Never use an old connector when installing a new cooktop. If the hard-piping method is used, you must carefully align the pipe; the cooktop cannot be moved after the connection is made. To prevent gas leaks, apply pipe-joint compound or wrap pipe-thread tape with Teflon on all male (external) pipe threads. 1. Attach the gas pressure regulator (included with the cooktop) to the cooktop pipe nipple inlet.
Installation instructions Step 5. Electrical connections. WARNING • Disconnect all electrical power of the main circuit breaker or fuse box before installing. • BEFORE OPERATING OR TESTING, follow the grounding requirements on pages 14 in this manual. Improper connection of the grounding plug can result in a rick of electric shock. • All gas cooktops come with a power cord. The power cord is connected to the bottom of the cooktop. Please review “Electrical requirements” on pages 13.
2. Install the burner head so that the electrode passes through the opening for the electrode. Make sure the burner head lies flat on the stove top. Burner Cap 1. Match the burner caps to the burners by size, and then re-install the caps on the burner heads. CAUTION Make sure each cap is re-installed on the correct burner head, is centered on the burner head, and lies flat. Round Burner head 1. Orient the burner head so that the opening for the electrode lines up with the electrode. 2.
Installation instructions Step 7. Check the ignition of cooktop burners Step 8. Checking the flame quality. Check the operation of all cooktop burners after the cooktop has been installed and assembled, gas supply lines have been carefully checked for leaks, and electrical power cord has been plugged in. All combustion flames need to be visually checked to determine their flame quality. To turn on a cooktop burner OFF 2 HI LO 1 1.
Step 9. Install the grates. NOTE Install the grates as instructed below for longest life. When installed properly, the openings in the grates are centered over the burners. The three cooktop grates are designed to fit in specific positions on the cooktop. For maximum stability, these grates should only be used in their proper positions. • Please place the grate marked with the letter ‘L’ on the left side, and the one with the letter ‘R’ on the right side.
Installation instructions Step 10. Final installation checklist WARNING • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. • Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor cooktop cannot be overemphasized. You have just completed installing your cooktop. Make sure all control knobs are in the off position.
Supplied parts BURNER ORIFICE SIZES AND OUTPUT RATINGS (Natural Gas 5 in WCP) The following parts make up the LP conversion kit: ORIFICES/ORIFICES/ORIFICIOS LR(WHT) LF(WHT) Burner Location BTU Rate Orifice size [mm] RF 13,000 1.64 LF 9,500 1.40 RR 5,000 1.01 LR 9,500 1.40 Center 19,000 In: 0.70 / Out: 1.30 (2 pcs) RR(YEL) CENTER Out(PURPLE) In(GRAY) RF(RED) DG69-00549A (PAD SHEET) NOTE 115 DTG30P875N*/DTG36P875N* Orifice markings: 115 – Denotes 1.15 mm orifice size opening.
Installation instructions Converting the pressure regulator Required tools NOTE Adjustable wrench /2” open-end wrench 1 Screwdrivers: Phillips If you are using LP gas to fuel the cooktop, the following steps and conversions must be made before the flames can be adjusted. 1. Using your fingers, turn the cap. And carefully look at the spring retainer to locate the NAT or LP position.
Converting the cooktop burners NOTE NOTE If you are using LP gas to fuel the cooktop, the following steps and conversions must be made before the flames can be adjusted. 1. Lift off the cooktop burner caps and the cooktop burner heads from the cooktop burner manifold cups. Cap Cooktop Burner Locations Burner Head Burner Cup 2. Using a 9/32” or 7 mm nut driver, remove the burner orifice from the bottom of each burner manifold cup.
Installation instructions Adjusting low flame setting on cooktop burners Combustion flame quality All Cooktop burner flames should be checked at their lowest setting. Use the following steps to check and adjust the cooktop burner settings. 1 NOTES • Low setting adjustments should always be made with two or more burners operating at the same time. • Call for service when you need to adjust the inner flame of the cooktop center burner settings. 1.
Memo Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.
Memo Dear Valued Customer, Thank you for purchasing Dacor. We hope our products empower your passion for cooking! Inside this box is a set of brass burner caps. These caps are meant to provide an elegant look to your new Dacor product. These caps may be used for cooking, but please know beforehand that they will discolor when used. This is a natural reaction of brass when it comes in contact with the gas flame.
Please visit www.Dacor.com to activate your warranty online. cut here WARRANTY INFORMATION IMPORTANT: Your warranty will not begin until you activate it online or return this form to Dacor. If you have purchased more than one Dacor product, please return all forms in one envelope, or activate the warranty for each product online. Please rest assured that under no conditions will Dacor sell your name or any of the information on this form for mailing list purposes.
DG68-01286A-00 Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745 ∙ Phone: 833-35-ELITE (833-353-5483) ∙ Fax: (626) 403-3130 ∙ www.dacor.com Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.
