Installation Instructions Modernist Rangetop DTT36M974L*/DTT48M976L*
Contents Contents Before you begin 5 Important About this manual Important note to the installer Important note to the consumer Important note to the servicer 5 5 5 6 6 Customer-service information 7 Important safety instructions 8 Read all instructions before using this appliance Symbols used in this manual State of California Proposition 65 warning (US only) Commonwealth of Massachusetts 8 8 8 8 Safety and warning information 9 General safety Fire safety Gas safety Electrical and grounding s
To Our Valued Customer: Congratulations on your purchase of the very latest in Dacor® products! Our unique combination of features, style and performance make us The Life of the Kitchen™, and a great addition to your home. In order to familiarize yourself with the controls, functions and full potential of your new Dacor Appliance, read this use and care manual thoroughly, beginning with the Before you begin section.
WARNING: Failure to follow the instructions in this manual exactly may cause a fire or explosion, and, consequently, property damage, personal injury, or death. • DO NOT keep or use gasoline or other flammable products near this appliance. • IF YOU SMELL GAS: - DO NOT light any appliances. - DO NOT touch any electrical switches. - DO NOT use any phone in your building. - Immediately call your gas supplier from a neighbor's phone, and follow the supplier's instructions.
Before you begin Important Installer • • The overall design and/or accessories may differ with the model. User • Keep this manual for personal reference and for that of inspectors, service personnel, etc. About this manual READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. Important note to the installer • • • • • • • Read all instructions contained in these installation instructions before installing the appliance.
Before you begin Important note to the consumer Before you begin Keep these instructions with your user manual for future reference. • As when using any appliance generating heat, there are certain safety precautions you should follow. • Be sure your appliance is installed and grounded properly by a qualified installer or service technician. • Make sure the wall coverings around the cooktop can withstand the heat generated by the appliance.
Customer-service information If you have questions or problems with installation, contact your Dacor dealer or the Dacor Customer Service Team. For repairs to Dacor appliances under warranty call the Dacor Distinctive Service line. Whenever you call, have the model and serial number of the appliance ready. The model and serial number are printed on a label. Dacor Customer Service Phone: (800) 793-0093 ex. 2813 (U.S.A. and Canada) Monday — Friday 6:00 a.m. to 5:00 p.m. Pacific Time Web site: www.dacor.
Important safety instructions READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE • • Electrical and gas equipment with moving parts can be dangerous. The important safety instructions in this manual are intended to minimize the risk of property damage, personal injury, and death. Be sure to read them. Keep this manual in a handy place so you can refer to it as needed. Symbols used in this manual WARNING Hazards or unsafe practices that may result in severe personal injury or death.
Safety and warning information General safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • • • • • • • Make sure the rangetop's hold-down brackets are properly installed. (See the Installation Instructions for details.) Do not let children sit/stand on the appliance or play with any of its parts. Do not leave children unattended in the kitchen when the appliance is in use.
Safety and warning information Fire safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • • • Do not store/place/use combustible materials (e.g., paper, plastic, pot holders, linens, gasoline, alcohol) near the appliance. Do not wear loose fitting or hanging garments while using the appliance. Safety and warning information To avoid grease buildup, regularly clean the vents.
Gas safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: If you smell gas: • • • Close the valve and do not use the appliance. Do not light a match, candle, or cigarette. Do not turn on any gas or electric appliances. • • • • • Do not touch an electrical switch or plug in a power cord. Do not use any phone in your building. Evacuate everyone from the building. Immediately call your gas supplier from a neighbor’s phone.
Safety and warning information Electrical and grounding safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • • • • • • Safety and warning information • • • Plug into a grounded 3-prong outlet. Do not remove the ground prong. Do not use an adapter or an extension cord. Do not use a damaged power plug, power cord, or loose power outlet. Do not modify the power plug, cord, or outlet. Do not put a fuse in a neutral or ground circuit.
Installation safety WARNING English 13 Safety and warning information To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • The appliance should be installed and properly grounded by a qualified installer, as specified in the Installation Instructions. Adjustments and service should be performed only by qualified gas appliance installer or service technician.
Safety and warning information Location safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • • Safety and warning information • This appliance is for indoor household use only. Do not install the appliance outdoors or anywhere that it will be exposed to weather/water or wind/ strong drafts. The appliance must be installed within easy reach of a grounded, 3-prong outlet.
Rangetop safety WARNING To reduce the risk of fire, electric shock, personal injury, or death, observe these precautions: • • • • • • • • • • • • • • Always use the LITE position to ignite a burner, then make sure the burner has ignited. If ignition fails, turn the knob to OFF, and wait a few minutes for the gas to dissipate. When you set a burner to simmer, do not turn the knob quickly. Make sure the flame stays on. Do not place any objects other than cookware on the rangetop.
Safety and warning information • • • Always use a minimum amount of oil for any type of frying. Always thaw food before frying, and do not frying food that is overly cold or that has clumps of ice attached to it. Always let the oil/fat in the cookware to cool to room temperature before moving the cookware. To avoid delayed-eruptive boiling, let hot oil/fat stand at least 20 seconds after turning off the burner so the temperature can stabilize.
Product specifications What’s in the box Parts supplied Common Manual Regulator (1) * Bolt (2) Washer (2) Envelope (1) 36" : DTT36M974L* Cooktop burner grates (2) Burner heads (4) and Brass caps (5) Porcelain caps (4) Burner heads (6) and Brass caps (7) Porcelain caps (6) 48" : DTT48M976L* NOTE • • • Make sure you have received all of the supplied parts shown above. If your cooktop was damaged during shipping or some specified parts are missing, contact your local retailer.
Product specifications Parts needed Gas line shut-off valve 135-degree elbow (optional) Flexible metal Flare union adapter ¾ Flare union adapter ½ appliance connector in (NPT) x ½ in (ID) in (NPT) x ½ in (ID) ½ in (ID) x 5 ft 90-degree elbow (optional) Tools needed Product specifications Flat-blade screwdriver Phillips screwdriver Open-end or adjustable wrench Pipe wrench (2) ¼" Nut driver Pencil and ruler Level Pipe joint compound Utility knife Soapy water solution Pliers Saber saw 18 En
Installation requirements Pre-installation checklist 1. Before preparing the opening in the countertop, verify that there will be no conflict between the rangetop chassis and anything in the cabinet below. 2. Remove packing materials, grate boxes, regulator with literature, and literature package from the appliance, verify that all items are present before beginning the installation. Location requirements BEFORE YOU BEGIN installing the appliance, see the information, dimensions, and clearances below.
Installation requirements Maintain the following minimum clearance dimensions 13” (33.0 mm) max.3 1 Vertical to combustible surface from rangetop grate level; if installing an overhead vent hood, also check the hood specifications for minimum required clearances. 2 See Cabinet/Countertop Dimensions - Top View. B Note 2 30” (762 mm) min.1 18” (457 mm) min.
Overall cooktop dimensions DTT36M974L* 36" (91.1 cm) 28 3/16" (71.6 cm) 27 1/2" (69.9 cm) 25 11/16" (65.3 cm) 22 1/4" (56.
Installation requirements DTT48M976L* 48" (121.6 cm) 28 3/16" (71.6 cm) 27 1/2" (69.9 cm) 25 11/16" (65.3 cm) 22 1/4" (56.
Cutout dimensions of countertop 10” (25.4 cm) to combustible side wall min. both sides 1 1/2” (3.8 cm) typical countertop thickness 1/2” (1.3 cm) overhang, both sides 7 3/4” (19.7 cm) A Recommended gas and electrical service location, consult local code Mounting platform 1” (2.5 cm) min. thickness 36” (91.4 cm) typical Cabinet/Countertop Dimensions - Front View 24” (61.0 cm) Installation requirements Installed control panel overhang 1 3/8” (3.
Installation requirements Gas and electrical connections at right rear section of chassis 24” (61.0 cm) Installed control panel overhang 1 3/8” (3.5 cm) Countertop Cabinet face Mounting platform Gas connection and power cord may be routed through bottom or back of chassis Installed Rangetop - Side View Increase countertop and overhang additional 2 1/2” (6.4 cm) min. for combustible rear wall above countertop Non-combustible rear wall, rear of mounting platform 10” (25.4 cm) min.
NOTE Gas and electrical connections may only be routed through the bottom of the rangetop when installed with a downdraft vent. 3/8” (1.0 cm) min. countertop overhang 2 5/8” (6.7 cm) Non combustible rear wall recommended 10” (2.5 cm) min. to combustible wall above countertop, both sides C Open to below to allow for raised vent, gas and electrical connections 26 5/8” (67.6 cm) min. cabinet depth 1/2” (1.3 cm) countertop overhang 1/2” (1.3 cm) countertop overhang 1” (2.
Installation requirements 3/8” min. (1.0 cm) flat countertop overhang required behind cutout Countertop Stiffener DTT36M974L* or DTT48M976L* rangetop 3/8” min. (1.0 cm) space behind downdraft vent chassis to clear stiffener Minimum countertop height: 30 1/4" (76.
Utility locations and dimensions Rear side F D Power cord 393/8” (100.0 cm) long G E 3 /8”-18 NPT male gas inlet DTT36M974L* DTT48M976L* D 3 1/2" (8.9 cm) 4" (10.1 cm) E 4 11/16 (11.9 cm) 4 11/16 (11.9 cm) F 5 1/8" (13 cm) 16 1/2" (41.9 cm) G 2 11/16" (6.9 cm) 2 11/16" (6.
Installation requirements Gas supply requirements Provide adequate gas supply This appliance is designed to operate at a manifold pressure of 5 in (13 cm) of water column on natural gas or 10 in (25 cm) of water column on LP gas (propane or butane). Make sure you are supplying your appliance with the type of gas for which it is designed. When checking for proper operation of the regulator, the inlet pressure must be at least 1 in (2.5 cm) greater than the operating (manifold) pressure as given.
Special gas requirements (gas models sold in Massachusetts) COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS: WARNING • • • • Gas leaks may occur in your system, creating a dangerous situation. - Gas leaks may not be detected by smell alone. - Gas suppliers recommend installing a UL-approved gas detector according to manufacturer specifications. The appliance must be installed by a plumber or gas fitter certified by the State of Massachusetts.
Installation requirements Rangetops - All gas models are equipped with a power cord with an equipment-grounding conductor and a grounding plug. - All gas models in the US and Canada require a 120 V, 60-Hz, AC, approved electrical service with 20-amp circuit breaker or time-delay fuse. NOTE Re-ignition may malfunction if the voltage between Neutral and Ground is over 20 VAC. Make sure the voltage is under 20 VAC. Grounding • • • • • • All rangetops must be grounded for personal safety.
Installation instructions Installing your rangetop IMPORTANT: Carefully read these instructions and the Important Safety Instructions section at the front of this manual BEFORE installing/operating the rangetop. Improper installation, adjustment, service, or maintenance can lead to personal injury and property damage. NOTE To ensure proper installation, you should hire a qualified professional. Unpacking the rangetop 1. Remove all packaging material. (Failure to do so could damage the appliance.) 2.
Installation instructions Connecting the gas supply 1. Shut off the main gas-supply valve before disconnecting the old rangetop. 2. Complete the gas hookup. 3. Open the gas valve, and relight the burners on any other gas appliances. NOTE Because hard piping restricts movement of the appliance, use a CSA International-certified flexible metal appliance connector unless local codes require hard piping.
Never install an old connector on a new appliance. For hard piping, you need to carefully align the pipe; the appliance cannot be moved after the connection is made. To prevent gas leaks, apply pipe-joint compound or wrap pipe-thread tape with Teflon on all male (external) pipe threads. 1. Attach the provided gas-pressure regulator to the rangetop pipe nipple inlet. (For tight installations, the regulator may be installed upstream from the nipple, anywhere between the shut-off valve and the rangetop.
Installation instructions Checking for gas leaks WARNING To prevent an explosion/fire hazard possibly leading to personal injury or death, DO NOT use a flame to check for gas leaks. When using pressures above 1/2 psig to test the home gas-supply system, disconnect the appliance and individual shut-off valve from the gas-supply piping. When using pressures of 1/2 psig or less to test the gas-supply system, isolate the rangetop from the system by closing the individual shut-off valve. 1.
Assembling the rangetop burners CAUTION • • • Do not operate the rangetop burners without all burner parts in place. Do not push in any rangetop controls while removing the burner; a slight electrical shock might result, perhaps causing you to knock over hot cookware. Do not risk electric shock by removing the top or touching the electrode of any burner while another burner is on. 1. Place the burner heads on the burner bases as shown at left. (The electrodes fit in the slot in the bottom of the heads.
Installation instructions Dual Burner head / caps 1. Orient the burner head so the opening for the electrode aligns with the electrode. 2. Install the burner head so the electrode passes through its opening in the head. Ensure the burner head lies flat on the stove top. 3. Match the burner caps to the burners by size, then install the caps on the heads.
Round Burner head / caps 1. Put the burner heads on the burner bases as shown at left. The bottom of the head fits within the burner base. 2. Turn the head until it drops into place. Twist the head back and forth slightly to ensure it is properly seated. 3. Put the burner caps (brass or porcelain) atop the burner heads. The ridge around the bottom edge of the cap fits around the top of the burner head. CAUTION Ensure all burner components (heads and caps) rest flat and snugly in place.
Installation instructions SimmerSear Burner Assembly (18K BTU Burner) Burner head Locating tab 1. Put the burner heads in place as shown below. The locating tab on the burner head goes in the keyed hole as shown. Burner base Keyed hole Burner ring Tabs Slots Installation instructions Ridge on bottom of burner cap 2. Put the burner rings on the burner heads as shown below. Match the tabs on the bottom of the ring to the slots on the burner head.
Verifying burner function After the cooktop is fully installed, connected, assembled, and plugged in, check the function of all burners. To turn on a cooktop burner OFF M LO HI 1. Push in, and turn a burner control knob to flame symbol. (A “clicking” sound indicates the electronic ignition system is functional. The burner ignites about 4 seconds later, after the air is purged from the gas line.) 2. After the burner ignites, turn the knob to the desired setting.
Installation instructions Checking flame quality All burner flames must be visually checked to assess their quality. CAUTION If you want measure the flame, take care to avoid burn injuries. 1 2 1. Soft blue flames—Normal for natural gas operation. 2. Yellow tips on outer cones—Normal for LP gas operation. 3. Yellow flames—Abnormal for any gas operation; call for service. NOTE 3 Installation instructions 40 English If the burner flame looks like Example 3, call for service, and do not use the cooktop.
Installing the grates NOTE For best results and longest life, install the grates as instructed below. When installed properly, the openings in the grates are centered over the burners. The grates occupy specific positions on the rangetop. For maximum stability and safe operation, these grates should only be used in their proper positions. The back of the right grate is notched to help orient the grates correctly. (See the graphic below.) To correctly position the grates: 1.
Installation instructions Final installation checklist WARNING • • To ensure a safe, proper installation, the installer should complete this checklist to ensure the installation was proper and complete. The owner shall be responsible for the rangetop's proper installation, the importance of which cannot be overstated. After installing the rangetop, ensure all control knobs are OFF. Review this checklist to confirm the rangetop is properly installed and ready to operate.
DG68-00942A-00 Dacor ∙ 14425 Clark Avenue, City of Industry, CA 91745 ∙ Phone: (800) 793-0093 ∙ Fax: (626) 403-3130 ∙ www.dacor.