cacor a rare rae Installation 24-Inch Built-in Dishwasher Models: EDWH245S and IDWH24 Part No. 106842 Rev.
Table of Contents Important Safety Instructions ...........ccceceeeee Important Information About Safety Instructions... Safety Symbols and Labels ................ccccceeees General Safety Precautions ..................cccccee Product Specifications ............cccccceeeeeeeeeeeeeeeees Product DIMENSIONS ...........cccccececeeeseeeeeeeeeeeeees Planning the Installation..............cccceccececeereree Electrical Specifications 0.0.0... cccceneeeeee Water Supply Specifications .............
Important Safety Instructions Important Information About Safety Symbols and Labels Safety Instructions DANGER The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand. See Customer Service Information.
Important Safety Instructions General Safety Precautions WARNING - To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING Use this dishwasher.only for its intended purpose as outlined in the use and care manual--|t is not intended for.commercial-use. Read the use and:care manual completely before use.
Product Specifications Product Dimensions Depth with door open -~a—— 49 3/4” (126.4 cm) Depth with door closed ~ Cc ke - D Handle depth >| “i | I> Drain hose p Front y shown Y Style varies, model EDWH24S Product tolerances: 41/16” (1.6 mm) Depth dimensions allow Side for hose on back of unit L_5 1/4” (13.5 cm) to W748" (18.5 cm) Y Shipping weight: 108 Ibs. (49 Kg) —>| |< 2” (50.0 cm) Model Description A B c D' EDWH248 Stainless steel front panel 24” (61.0 cm)] 34 3/8” (87.
Planning the Installation WARNING Observe.all.governing codes and ordinances. during planning and insiallation. Contact your local building departmeni for further information. Electrical Specifications WARNING Electrical and grounding connections must comply with the applicable portions of the national-elecirical code and/or other local electrical codes. The dishwasher comes with an electrical cord with a three prong grounding plug for 120 volts, 15 amp supplied.
Planning the Installation * The electrical outlet or junction box must meet the Electrical Specifications. The electrical service must also be installed close by in a cabinet adjacent to the location selected so that the power cable can be disconnected without removing the appliance from the cutout.
Planning the Installation Preparing the Drain CAUTION Keep the factory installed high loop drain hose in place to ensure proper:dishwasher-operation. Do not modify or move.the mounting bracket in any manner. If it is necessary to. lengthen the hose, install-an aftermarket drain extension kit, available at most home improvement stores. IMPORTANT: Should a drain hose longer than the one provided be required, use a hose extension approved for detergents and high temperature water.
Installation Instructions Verify the Package Contents Remove all styrofoam and plastic wrap from the dishwasher. Be sure to remove the toe kick and toe kick insulation from the top of the dishwasher packaging. With the assistance of at least one person, remove the dishwasher from the shipping pallet. Place the unit to the side of the cabinet opening. Remove the “O” ring attached to the water line in a plastic bag. Set it aside for use during the Water Line Connection.
Installation Instructions Installation Preparation WARNING Before working on wiring for-any electrical. appliance, be sure.the electrical-power. has been turned off.at the breaker/fuse box..Place.a tag at the disconnect switch indicating that you are working onthe circuit. Moving this appliance requires two people. Do not attempt to install-or lift it without assistance. To prevent personal injury, wear hand protection when moving this appliance.
Installation Handle Installation (Model EDWH24S) Instructions 4. Install the door handle according to the handle installation instructions. To make larger tension adjustments to the door springs, remove the back of the springs from the dishwasher by turning them outwards. Move them one hole farther back or forward, then make small adjustments as outlined in step 3 as necessary. Adjust the Door Springs Before installation, open the door to make sure it stays open at any angle.
Installation Level the Dishwasher Instructions 4. Open the door and pull the bottom rack out of the dishwasher. Check to make sure the dishwasher floor is level left to right using a level. Adjust the front legs as necessary. 5. Using a flat blade screwdriver, turn the rear leg adjustment screw until the floor of the dishwasher is level front to back. 6. Leave the retaining nuts loose to allow for final leveling after the unit is pushed into place. CAUTION Alevel unit is very.
Installation 4. If anonmetallic cable is being used, install a UL-listed strain relief bushing on the back of the dishwasher. 5. Connect the white wire on the cable to the “N’” terminal on the dishwasher terminal block as shown below. 6. Connect the black wire on the cable to the “L’” terminal on the terminal block. 7. Connect the ground (green) wire on the cable using a loop or spade terminal to the ground connection screw located on the dishwasher chassis. ae Junction box Instructions 3.
Installation Drain Connection CAUTION «For proper-dishwasher operation and drainage, the drain line must be routed through the bottom ofthe cabinet and up.to.the drain or-air gap connection. The drain hose or air gap outlet must connect above the sink trap. «_1. 2. 3. Instructions 5. cable, water line and drain hose are free of pinches or kinks. 6. Cut the drain hose adapter on the end of the drain hose to the appropriate size for the air gap, waste tee, disposer connection or hose extension. 1.
Installation Final Leveling Check to make sure that adjacent drawers and cupboards can be opened when the dishwasher door is open. Reposition the dishwasher if necessary. Check that there is a 1/8” (3 mm) space between the top of the dishwasher door and the underside of the cabinet. 1/8” (3 mm) Attaching the Anti+tip Brackets CAUTION Make sure to anchor. one anti-tip bracket on each side of the dishwasher. 1.
Installation ‘4° Anti+ti fp Brackets (Cont. 5. Cover the screw holes on the sides with the supplied plastic plugs. Push in the plugs diagonally to fit them in place. Instructions 5. Hang the toe kick on the brackets as shown. Check to make sure that the toe kick is even with the kitchen cabinet toe kick. If necessary, remove the toe kick and readjust the brackets. Installation Checklist 6. Replace the top rack. Insta | | INg 1.
dacor 15
16 dacor.
cdacor Item No., 80 895 92 Rev. 02 The Life of the Kitchen® Dacor e 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 Phone: (800) 793-0093 e Fax: (626) 403-3130 e www.Dacor.