Installation guide
Installation
Instructions
3.
Raise
the
door
so
that
it
is
at
a
15°
angle
from
the
front
of
the
oven.
Hold
the
door
with
one
hand
on
each
side.
Lift
the
door
up
and
out.
Se
SS
~.
SS
N
le
~
Door
Gripping
9
“—
Points
Install
the
Oven
in
the
Cabinet
WARNING
2.
Support
the
oven
at
all
times
until
it
is
secured
into
the
cabinet.
Be
certain
to
take
all
necessary
safety
precau-
tions.
3.
Resting
the
oven
on
the
cabinet
support
platform,
slide
the
oven
into
the
recessed
area
until
the
rear
edge
of
the
oven
trim
post
is
flush
with
the
cabinet
face
and
the
oven
is
centered
within
the
cutout.
Ensure
that
the
electrical
conduit
slides
through
the
opening
in
the
cabinet
platform
or
coils
above
the
oven
chassis
as
the
oven
is
slid
into
place.
Do
not
trap
the
appliance
cable
between
the
oven
case back
and
the
rear
wail.
4.
Make
sure
the
oven
is
resting
level.
Shim
it
if
neces-
sary.
WARNING
When
installing
the
mounting
screws
into
composite
cabinets,
install
them
into
the
sides
of
the
cabinet
only.
Mounting
screws
installed-into
the
front
of
composite
cabinets
will
have
a
tendency
to
pull-loose.
«Use
an
appliance
dolly
to
move
the
appliance
when
installing
it/or
removing
it
from
the
wall
for
service..Use
of
an
appliance
dolly
will
minimize.
the
risk
of
personal
injury-as
a.result
ofthe
oven
tipping.
«
Failure
to
install-tne.
mounting
screws
may
result
in
movement.or
tipping
of
the
oven
during
use,
or.
per-
sonal
injury.
«Do
not:
block
the
oven
air
exhaust
and
intake
located
at
the
bottom
of
the
oven
door(s).
Blocking
the
airflow
may
cause
cabinet
damage
and
poor.
baking
perfor-
mance.
IMPORTANT
An_-oven
that
is
‘not
level
may
provide
poor-or
inconsistent
baking
results.
1.
Lift
the
oven
up
to
the
cabinet
cutout
using
the
handles
and
gripping
points
shown.
Use
extreme
caution
when
lifting
the
appliance,
because
it
is
heavy.
Trim
post
Handle
“—
Gripping
point
5.
Find
the
mounting
hole
locations
in
the
front
and
side
of
the
oven
trim
posts.
Drill
1/16”
pilot
holes
in
the
cabinet
through
the
front
or
side
of
the
trim
posts.
Single
oven
models
require
four
(4)
holes,
while
double
oven
models
require
six
(6).
6.
Install
the
#6
x
3/4”
screws
provided
in
the
instructions
envelope.
Do
not
over-tighten.
Oa
eee
@a8
eee
oog
O00000
@80
=
=
——
i
nd
——
—
ee
[of
©
6
f°]
«¢
ey
cy
|
>
zy
=z
[Us
l
monnnnnnmmmnige
[0
|||
—
—
a
—
©
oO
oe
fam
f|
°
F|
=
<a
3p
I’
2 I
ll
a
SI
= =
—
dacor
13