Installation Epicure ® 30-Inch Instructions Gas Range For use with models ER30G and ER3OGI THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS COOKING APPLIANCES. PartNo. 106174 Rev.
Important Safety Instructions ..................................................... Important Information About Safety Instructions ......................... General Safety Precautions ........................................................ Installation Specifications ........................................................... Product Dimensions .................................................................... Electrical Power Supply Requirements ......................................
Important Information About Safety Instructions The Important Safety Instructions and warnings in this Manual are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this appliance. Always contact the Dacor Customer Service Team about problems or conditions you do not understand.
General Safety Precautions To reduce the risk of fire, explosion, electric shock, serJous Jnjury or death when JnstallJng or usJng thJs applJance, follow basJc safety precautJons, JncludJng the followJng: • Read the accompanying • Keep packaging materials away from children. Plastic sheets and bags can cause suffocation • If you receive a damaged product, immediately contact your dealer or builder.
• For your safety, do not use the oven to cook without the convection filter installed. When the filter is not installed, the spinning fan blades at the back of the oven are exposed. • The cooktop should never be operated without the knobs and trim rings in place. Non-stick coatings, when heated, can be harmful to birds. Remove birds to a separate, well-ventilated cooking. • room during Always ensure that the light fixture lens cover is in place when using the oven.
Gas Supply Requirements • Be certain that the range being installed is correct for the gas service being provided (natural gas or LP gas). Check your local building codes for the proper method of installation. In the absence of local codes, this appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54. An external manual shut-off valve must be installed between the gas inlet and the range for the purpose of turning on or shutting off gas to the appliance.
• Cabinet Layout Carefully check the location where the range is to be installed. For best performance, the range should be placed away from drafts that may be caused by doors, windows and heating and air conditioning outlets. Any openings in the wall behind the appliance or in the floor underneath it must be sealed.
Gas and Electrical Locations The installation must allow for the following: Access to the gas shut-off valve when the unit is installed, Access to the electrical outlet, when the range is in place, E E The gas supply piping, gas shut-off valve and the electrical junction box or receptacle must be located so they do not interfere with the range when it is installed, The electrical outlet and gas shut off valve must be located so that the range can be pulled out for service while the appliance remains conne
Backguard Kit Installation , See the inside cover for available part numbers and compatibility. , If installing a backguard other than the standard size, install it before pushing the range into place. Install the kit according to the accompanying installation instructions. A T-20 Torx driver is required. 1 The trim kit is for use with model ER30GI with a selfrimming cutout only. Install the trim pieces before pushing the range into place. A T-20 Torx driver is required.
Self-Rimming Trim Installation (cont.) 8. Remove and retain the two (2) hex head screws from the top back corners of the sides of the chassis as shown. 10. Using two (2) of the provided #8 x 1/4 screws, attach the bracket to the backguard as shown. Each screw threads into the backguard through the hole in the back of the bracket. .) / ,) 11. Install the rear trim piece on the back side of the backguard with the two (2) remaining #8 x 1/4 screws.
Install the Anti-Tip Bracket Door Removal 1. Remove the door to make the range easier to move during the installation process. Locate the anti-tip foot on the back of the range and turn it until the bottom of it is 1/16" (2 mm) off the floor. o o I 1. Open the door to its fully opened position. 2. Use a flat blade screwdriver to rotate the catch over the retaining arm on both hinges. Back of Range _'- Anti-Tip Foot , 3. Retaining arm Locate the anti-tip bracket included in the parts box.
Gas Connection IMPORTANT: The installed gas pressure regulator is preset at the factory for the type of gas intended for use with the appliance. Verify that the appliance is compatible with the type of gas available by checking the product data label attached to the appliance. Ranges intended for use with LP gases will have "LP" as a part of the model number. Consult your dealer if the range is not compatible with your gas supply. 1. , , , , 6.
Moving the Range to Final Location 1. , Peel the protective plastic coating off of the range, including the range door. Uncoil the power cord and route it to the electrical outlet so that it does not become trapped behind the range when it is pushed back. Do not connect the power plug until you are ready to verify proper operation. , Carefully slide the range into position taking the slack out of the power cord as you push the unit into place.
Cooktop Assembly , , Remove the burner rings, burner caps and grates from their shipping cartons. Install the burners as shown. Gently twist each piece back and forth after installation to make sure it is properly seated. A small gap below the bottom of the burner ring is normal. 3. Gently set the grates on top of the spill tray. Put the legs of each grate inside the corresponding dimples. 4.
If the range does not operate properly, follow these troubleshooting steps: Verifying Proper Operation 1. , , 3. Before beginning the test procedure, make sure all range control valves are in the "OFF" position, and all burner rings, burner cap and grates are properly positioned on the spill tray. Make sure the gas supply valve is in the on position and that the main gas valve to the building is open. Check to see if the oven burner light flashes on and off once a second.
z o 7°::>o of_// -- oo c ° ;:;u_ _,. ® z -1:> 'i 120VAC _ -- _- EyJ-- oo _ oo __co _ from [I Burner Switch ® o u) ou c,_ ;;on3 ..
dacar 15
16 =::_acar
The Life of the Kitchen? Dacor • 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 • Phone: (800) 793-0093 • Fax: (626)403-3130 American Made*Family • www.Dacor.
