Installation Instructions Epicure 30 - Inch Gas Range ® For use with models ER30G and ER30GI THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS COOKING APPLIANCES. Part No. 106174 Rev.
Table of Contents Important Safety Instructions...................................................... 1 Important Information About Safety Instructions......................... 2 General Safety Precautions......................................................... 2 Installation Specifications............................................................3 Product Dimensions.....................................................................3 Electrical Power Supply Requirements.................................
Important Safety Instructions Important Information About Safety Instructions The Important Safety Instructions and warnings in this Manual are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this appliance. Always contact the Dacor Customer Service Team about problems or conditions you do not understand. Safety Symbols and Labels DANGER Immediate hazards that WILL result in severe personal injury or death.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, explosion, electric shock, serious injury or death when installing or using this appliance, follow basic safety precautions, including the following: WARNING 2 • Read the accompanying use and care manual completely before operating this appliance. • Keep packaging materials away from children. Plastic sheets and bags can cause suffocation.
Important Safety Instructions WARNING • For your safety, do not use the oven to cook without the convection filter installed. When the filter is not installed, the spinning fan blades at the back of the oven are exposed. • The cooktop should never be operated without the knobs and trim rings in place. • Non-stick coatings, when heated, can be harmful to birds. Remove birds to a separate, well-ventilated room during cooking.
Installation Specifications Gas Supply Requirements WARNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. To prevent an electric shock hazard, the power supply must meet the specifications stated below. It is the owner’s responsibility to make sure that the electrical service meets electrical requirements and that the electrical outlet has been properly installed by a licensed electrician.
Installation Specifications Cabinet Layout WARNING • Any openings in the wall behind the appliance or in the floor underneath it must be sealed. • If cabinet storage space is to be provided directly above the range, the risk of personal injury may be reduced by installing a ventilating hood that projects horizontally a minimum of 5 inches beyond the face of the cabinets. Failure to meet or exceed the maximum and minimum dimensions/clearances stated may result in a fire hazard.
Installation Specifications Gas and Electrical Locations ◊ Access to the gas shut-off valve when the unit is installed. ◊ Access to the electrical outlet, when the range is in place. ◊ The gas supply piping, gas shut-off valve and the electrical junction box or receptacle must be located so they do not interfere with the range when it is installed. ◊ The electrical outlet and gas shut off valve must be located so that the range can be pulled out for service while the appliance remains connected.
Installation Instructions Backguard Kit Installation See the inside cover for available part numbers and compatibility. If installing a backguard other than the standard size, install it before pushing the range into place. Install the kit according to the accompanying installation instructions. A T-20 Torx driver is required. Self-Rimming Trim Installation 5. Slide the provided left and right trim pieces onto the range. The overhang on each piece goes toward the back. 6.
Installation Instructions Self-Rimming Trim Installation (cont.) 8. Remove and retain the two (2) hex head screws from the top back corners of the sides of the chassis as shown. 10. Using two (2) of the provided #8 x 1/4 screws, attach the bracket to the backguard as shown. Each screw threads into the backguard through the hole in the back of the bracket. 11. Install the rear trim piece on the back side of the backguard with the two (2) remaining #8 x 1/4 screws. 9.
Installation Instructions Install the Anti-Tip Bracket Door Removal 1. Locate the anti-tip foot on the back of the range and turn it until the bottom of it is 1/16” (2 mm) off the floor. Remove the door to make the range easier to move during the installation process. WARNING • Do not attempt to disengage the hinge catches with the door removed from the oven. The hinge springs could release causing personal injury. • Do not lift or carry the oven door by the door handle. 1.
Installation Instructions Gas Connection WARNING • Make sure the gas is turned off at the gas supply valve before connecting the gas line. • Verify that the gas supply meets specifications before connection. See page 4. • Do not apply excessive pressure when tightening gas connections and fittings. • Do not use Teflon tape or plumber’s putty on flexible gas line connections. • Test the gas lines for leaks as instructed before use.
Installation Instructions Moving the Range to Final Location 1. Peel the protective plastic coating off of the range, including the range door. 2. Uncoil the power cord and route it to the electrical outlet so that it does not become trapped behind the range when it is pushed back. Do not connect the power plug until you are ready to verify proper operation. 3. Carefully slide the range into position taking the slack out of the power cord as you push the unit into place.
Installation Instructions Cooktop Assembly WARNING Never attempt to operate the range’s cooktop with any of the burner rings, burner caps or grates removed. 1. Remove the burner rings, burner caps and grates from their shipping cartons. 2. Install the burners as shown. Gently twist each piece back and forth after installation to make sure it is properly seated. A small gap below the bottom of the burner ring is normal. 3. Gently set the grates on top of the spill tray.
Installation Instructions Verifying Proper Operation If the range does not operate properly, follow these troubleshooting steps: WARNING Before operating the range, read the accompanying use and care manual completely. 1. Before beginning the test procedure, make sure all range control valves are in the “OFF” position, and all burner rings, burner cap and grates are properly positioned on the spill tray. 2. Turn on the gas supply at the shut-off valve. “OFF” symbol on knob 3.
Wiring Diagram 4 LED INDICATOR RR B 3 LED INDICATOR RF B 2 1 LED INDICATOR LR B W W B B LED INDICATOR LF B W B W B W P2 1 BROIL HSI BAKE HSI P7 2 4 6 8 10 1 3 5 7 9 BBBBB P5 6 5 4 3 2 1 P3 4 3 2 1 P6 1 2 3 4 5 6 7 8 9 10 11 12 B Burner LEDs W B B B WIRE COLOR CODE: W-WHITE R-RED Y-YELLOW O-ORANGE B-BLACK BR-BROWN BL-BLUE GR-GREEN V-VIOLET IGNITOR, LR BURNER B BR P10 2 W W Controller Board P8 IGNITOR, LF BURNER Single Point Spark Module 1 IGNITOR, RF BURNER P1 2 W W
Notes 15
Notes 16
Dacor ● 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.Dacor.
