Installation Instructions Epicure ® Ranges For use with models: EGR30, ERD30, ERD60 Part No. 65089 Rev.
Table of Contents Important Safety Instructions...................................................... 1 General Safety Precautions......................................................... 1 Product Specifications.................................................................3 Product Dimensions.....................................................................3 Gas Supply Requirements........................................................... 3 Electrical Power Supply Requirements.......................
Important Safety Instructions Safety Symbols and Labels Important Information About Safety Instructions DANGER The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Immediate hazards that WILL result in severe personal injury or death. Always contact Dacor about problems or conditions you do not understand.
Important Safety Instructions General Safety Precautions (cont.) WARNING • Before performing any type of service or installation, make sure that the gas supply and electric power to the range are off. • NEVER block or cover any slots, holes or passages anywhere inside the oven or on the outside of the range or cover an oven rack with materials such as aluminum foil. Doing so blocks airflow through the oven and cooktop and may cause carbon monoxide poisoning or fire.
Product Specifications Product Dimensions Gas Supply Requirements NOTE: For ERD series models, all front-to-back depth dimensions are reduced by 1” (25mm) when the backguard and the full side panels are removed. Check your local building codes for the proper method of installation. In the absence of local codes, this appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223.1. Be certain that the appliance being installed is correct for the gas service being provided.
Planning the Installation WARNING • Both the gas supply piping and shut-off valve, and the electrical junction box/receptacle must be located so they do not interfere with the range when it is installed. In addition, the junction box must be located so the range can be removed for service when the conduit supplied with the unit is attached to the junction box. Do not lengthen the conduit or wiring provided with the range.
Installation Specifications 3/4" (19mm) Max. backsplash 1/4" (6mm) Min.
Installation Instructions WARNING • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • If the gas or electric service provided does not meet the product specifications, do not proceed with the installation. Call the selling dealer, the gas supplier or a licensed electrician. • This appliance must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of Massachusetts.
Installation Instructions Utility Locations 60” (1524mm) 30” (762mm) 6" (152mm) Backguard 6" (152mm) Backguard Power Cord Factory installed 3/4” regulator (1/2” supply ok) Power Cord Factory installed 3/4” regulator (1/2” supply ok) Gas and Electrical Locations - 30 Inch Models Electrical Connection Gas and Electrical Locations - 60 Inch Models Connecting to a Four-Wire Electrical System 1. Make sure power to the junction box is switched off at the circuit breaker or fuse box.
Installation Instructions Electrical Connection of ERD Series Ranges (continued) Cable from power supply Connecting to a Three-Wire Electrical System (where local codes permit) Junction box WARNING Do not connect the green appliance wire to the neutral (white) supply wire unless local building codes permit. 1. Make sure power to the junction box is switched off at the circuit breaker or fuse box. 2. Connect the green and white appliance wires to the neutral (white) supply wire in the junction box.
Installation Instructions Gas Connection WARNING • Make sure the gas is turned off at the gas supply valve before connecting the gas line. • Do not apply excessive pressure when tightening gas connections and fittings. • • Installing the Range Installation of Self-Rimming Configuration (Models ERD30 and EGR30 only) 1. Do not use teflon tape or plumber’s putty on gas flex line connections. Measure the distance from the floor to the countertop.
Installation Instructions Installing the Burner Components Verifying Proper Operation WARNING Never attempt to operate the cooktop section of the range with any of the burner rings, burner caps or grates removed. 1. Remove the brass burner rings, porcelain burner caps, and porcelain gates from their shipping packages. 2. Place each burner ring onto its corresponding burner base, being certain that the five alignment tabs slide into the matching notches in the base. 3.
Notes 11
Notes 12
Notes 13
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.