Installation Instructions Epicure ® Range For use with models ER3OD, ER3OD-C, ER3ODSR THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS COOKING APPLIANCES. Part No. 102187 Rev.
All specifications subject to change without notice. Dacor ® assumes no liability for changes to specifications. © 2007 Dacor, all rights reserved.
Important Safety Instructions .................................................. 1-3 Customer Service Information .................................................... 3 Planning the Installation ........................................................... 4-8 Electrical Requirements 4 Gas Supply Requirements 4 Product Dimensions 5 Cabinet Layout 7 Installation Instructions ..........................................................
General Safety Precautions To reduce the risk of fire, explosion, electric shock, serious injury or death when installing or using this appliance, follow basic safety _recautions, including the following: 2 • Read the accompanying • Keep packaging materials away from children. Plastic sheets and bags can cause suffocation. use and care manual completely before operating this appliance.
• • • • • Toprevent damage, remove themeatprobefromtheovenwhenitisnotbeingused Donotlinetheovenwithaluminum foilorothermaterials. Theseitemscanmeltorburnupduring self-cleaning andcause permanent damage totheoven. Donotleavemetalobjects, suchasaluminum foil,themeatprobe, cookiesheets, etc.onthebottom oftheoven.Objects lefton thebottom oftheovencoulddamage thebakeelement. Inaddition, theobjects themselves couldbedamaged. Thebakeandbroilelements arebehind glasspanels onthefloorandceiling oftheovenchamber.
Electrical Requirements Freestanding • Electrical Requirements IMPORTANT: The information below applies only to freestanding units equipped for use in the U.S.A. and units with the selfrimming option. ER30D/ER30DSR Circuit National Fire Protection Association 1 Batterymarch Park Quincy, Massachusetts 02269-9101 Circuit Total Required SPECIFICATIONS Connected Load 5.6 kW (24.2 Amp.) The ratings above are for reference only - refer to the range rating label (see page 3).
Product Dimensions Product tolerances: +1/16" (+1.6 mm), unless otherwise stated l\Gas GAS _' inlet _ _ , ,_ Range electrical cover removed access, B 1 - ELECTRICAL ACCESS DIMENSIONS A B C D 4 7/8" (124 mm) 21 3/4" (552 mm) 8 5/8" (219 mm) 10 3/16" (259 mm) * When using an appliance cord, the hole size must be increased to 1 1/8" by removing the conduit bracket inside the range electrical access box. A-_l ___C._,_ i 718" (22 mm) Dim.
Product Dimensions (continued) Product tolerances: +1/16" NOTE: Self-rimming integral backguards. (+1.6 mm), models unless otherwise are not compatible stated NOTE: Self-rimming models are designed to allow the trim to overlap the countertop when configured to the dimensions on page 8.
Cabinet Layout Gas and Electrical Service • Carefully check the location where the range is to be installed. For best performance, the range should be placed away from drafts that may be caused by doors, windows and heating and air conditionJng outlets. • • To reduce the risk of personal injury and to reduce accumulated smoke in the room, Dacor strongly recommends JnstalNng a range hood. A range hood should project horizontally a minimum of five (5) inches beyond the face of the cabinets.
Cabinet Layout (continued) Non-combustible rear wall recommeded 10" Min.\ (254 mm) APPROVED RAISED VENT MODELS: ERV30 or PRV30. 1/4" Min. (6 mm) Countertop _ 10" Min. -..
Changing the Backguard and ER3OD-C only) (models ER30D Installing the ATK3OSR Raised Vent Trim Kit (model ER3ODSRonly) Models ER30D and ER30D-C come standard with a 3" backguard installed• The 6" and 9" backguards are optional• To install the optional raised vent with self-rimming model ER30DSR, you must install the optional raised vent trim kit. To change To change the backguard: the trim on model ER30DSR: 1. Remove and retain the three (3) chrome screws on the front of the existing backguard.
ARSP3 Side Panel Kit Installation (cont.) 2. Close the door. Remove and retain the two screws from the back of the kick panel as shown below. Pull the kick panel free from the front of the unit. 8, Insert the tabs on the trim piece into the slots on the range. 6. Use the hex head screw (83023) removed from the side, a Torx head screw removed from the kick panel and the hex screws from the kit to attach the side panel to the range. Three (3) hex head screws attach the side.
9. With the door closed, reattach the kick panel to the range by snapping the ball studs on the back of the panel into the holes on the front panel of the range. Level and Adjust the Range Height Raise or lower the range to prepare for final installation: • For model ER30D and ER30D-C, adjust the height until the top edge of the trim around the edge of the of the cooktop is slightly higher than the countertop.
Removing the Oven Door Electrical Connection To make the range easier to move, remove the door to reduce weight. 1. Open the door to its fully opened position. 2. Rotate the catch over the retaining arm on each hinge. NOTE: Freestanding model ER30D-C is wired for use in Canada and comes from the factory pre-wired. If installing a pre-wired range, skip to Gas Supply Connection on page 17. Retaining arm 3. Lift the oven door to about a 15° angle from the vertical position. 4.
Connecting the Wiring to the Range Refer to the range rating label (see page 3) for power requirements.
Electrical Connection (Continued) Connecting the Conduit to the House Electrical Junction Box Connection to power supply Junction box Wire nut 3 places RED .WHITE •WHITE [_RED BLACK _ With the range positioned directly in front of the cabinet cutout, feed the appliance wires into the junction box. Depending upon local codes, utilize one of the three (3) methods shown to connect the appliance to the junction box. 2.
Separate No. 10 (minimum) Connection to power supply copper grounding wire Junction box Wire nut 4 places Connection to appliance (Page 13) 4 Wire Conduit Connection to Junction Box with External Ground No.
Electrical Connection (Continued) 5. Slide the end of the appliance cord into the strain relief from the bottom of the box. Appliance Cord Connections - Where Local Code Permits 6. Connect the white (neutral) wire to the neutral terminal in the box. 7. Connect the L1 wire to the L1 power supply terminal in the box. 8. Connect the L2 wire to the L2 power supply terminal in the box. 9.
Gas Connection Bare wire connections Loop and spade terminal connections L1 terminal Neutral terminal L2 terminal Link removed _ I = Ground screw _ --_ (_ o L2 wire Green wire White wire Strain relief L1 wire NOTE: The gas pressure regulator is pre-set at the factory for the type of gas intended for use with the appliance. To verify that the appliance is compatible with the type of gas available, check the range rating label (see page 3 for location).
Final Installation Installing the Burner Knobs 1. Peel the protective plastic coating off of the range, including the range door. 2. Carefully slide the range into position in the cutout. The rear anti-tip leg should engage the anti-tip bracket. 3. On self-rimming installations, reach under the range and adjust the legs, lowering the range until the trim just makes contact with the countertop on all three sides. 4. Use a level to make sure that the range does not tilt front to back or side to side.
Cooktop Assembly Spilt tray Remove the burner rings, burner caps and grates from their shipping packages. • • Stack burner Install the burners as shown. Gently set the grates on top of the spill tray. Put the legs of each grate inside the corresponding dimples. Crown burner Ridge on bottom of burner cap STEP 3: Install burner cap. Ridge on cap must surround top of ring. Ridge on bottom of burner cap STEP 2: Install burner ring. Line up ring tabs with head slots.
Installation Checklist Verifying Proper Operation Before operating the range, read the accompanying manual completely. use and care 1. Before beginning the test procedure, ensure that all cooktop control valves are in the OFF position, and all burner rings, burner caps and grates are properly positioned on the cooktop frame. Turn on the gas supply at the shut-off valve. 2. Plug Jnthe appliance cord, if applicable. Turn on power to the range at the circuit breaker or fuse box. 3.
• The Life of the Kitchen? Dacor • 600 Anton Blvd. Suite 1000 Costa Mesa, CA 92626 • Phone: (800) 793-0093 • Fax: (626)403-3130 • • • Family Owned American Made • www.Dacor.
