Installation Instructions Renaissance ® Range For use with models ER36D, ER36D-C, ER48D, ER48D-C THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS COOKING APPLIANCES. Part No. 100843 Rev.
Table of Contents Important Safety Instructions...................................................... 1 General Safety Precautions......................................................... 2 Customer Service Information.....................................................3 Planning the Installation............................................................... 4 Electrical Requirements...............................................................4 Electrical Requirements - Canada............................
Important Safety Instructions Important Information About Safety Instructions The Important Safety Instructions and warnings in this manual are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you do not understand.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, explosion, electric shock, serious injury or death when installing or using this appliance, follow basic safety precautions, including the following: WARNING 2 • Read the accompanying use and care manual before operating this appliance. • Keep packaging materials away from children. Plastic sheets and bags can cause suffocation. • If you receive a damaged product, immediately contact your dealer or builder.
Important Safety Instructions WARNING • To prevent damage, remove the meat probe from the oven(s) when it is not being used. • Do not line the oven(s) with aluminum foil or other materials. These items can melt or burn up during self-cleaning and cause permanent damage to the oven. • Do not leave metal objects, such as aluminum foil, the meat probe, cookie sheets, etc. on the bottom of the oven(s). Objects left on the bottom of the oven could damage the bake element.
Planning the Installation Electrical Requirements - Canada WARNING IMPORTANT: Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Electrical Requirements IMPORTANT: The information below does not apply to units equipped for use in Canada. It is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a licensed electrician.
Planning the Installation Product Dimensions Product tolerances: ±1/16” (±1.6 mm) Gas regulator access, cover removed GAS - ELECTRICAL ACCESS DIMENSIONS Model A B C D E* ER36D 5 5/8” (14.3 cm) 18 3/8” (46.7 cm) 10 3/4” (27.3 cm) 5 5/8” (14.9 cm) 7/8” (2.2 cm) ER48D 3 13/16” (9.7 cm) 18 11/16” (47.5 cm) 9 3/8” (23.8 cm) 5 3/4” (34.9 cm) 1 1/8” (2.9 cm) * The diameter on models equipped for use in Canada is ¼” (6.4 mm) larger than those stated.
Planning the Installation Cabinet Layout Gas and Electrical Service • Carefully check the location where the range is to be installed. For best performance, the range should be placed away from drafts that may be caused by doors, windows and heating and air conditioning outlets. • • To reduce the risk of personal injury and to reduce accumulated smoke in the room, Dacor strongly recommends installing a range hood.
Installation Instructions Preparing for Installation WARNING • If the gas or electric service provided does not meet the product specifications, do not proceed with the installation. Call the dealer, the gas supplier or a licensed electrician. • Before installing the range, you must locate and secure the anti-tip bracket to the floor. Install the Anti-Tip Bracket and Foot 1. Locate the anti-tip bracket included in the parts box. 2.
Installation Instructions Removing the Oven Door Electrical Connection WARNING • • WARNING Do not attempt to disengage the hinge catches with the door(s) removed from the range. The hinge springs could release causing personal injury. • Wire the range only in compliance with local ordinances. • Improper connection of the electrical wiring can cause an electric shock hazard and damage the appliance. Dacor is not responsible for damages resulting from improper installation.
Installation Instructions Refer to the range rating label (see page 3) for power requirements. There are four possible ways to wire the range: • 4 wire conduit • 3 wire conduit (where local codes permit) • 4 wire appliance cord (where local codes permit) • 3 wire appliance cord (where local codes permit) The sections below and on the following pages give directions for connecting each type of wiring harness.
Installation Instructions Electrical Connection (cont.) Connecting the Conduit to the House Electrical Junction Box WARNING Connection to power supply Junction box Do not connect the green appliance wire to the neutral (white) supply wire unless local building codes permit. NOTES: ◊ 1. The power supply must be properly polarized. Reverse polarity will result in continuous sparking of the electrodes, even after flame ignition.
Installation Instructions Separate No. 10 (minimum) copper grounding wire Connection to power supply Junction box Fasten clamp tightly on pipe Wire nut 4 places Connection to appliance (Page 9) 4 Wire Conduit Connection to Junction Box with External Ground No.
Installation Instructions Electrical Connection (cont.) 5. Slide the end of the appliance cord into the strain relief from the bottom of the box. Connecting an Appliance Cord to the Range - Where Local Code Permits 6. Connect the white (neutral) wire to the neutral terminal in the box. 7. Connect the L1 wire to the L1 power supply terminal in the box. 8. Connect the L2 wire to the L2 power supply terminal in the box. 9.
Installation Instructions Gas Connection WARNING Bare wire connections Loop and spade terminal connections L1 terminal • Make sure the gas supply valve is off and that the power to the range is turned off at the circuit breaker or fuse box prior to connecting the gas line. • Do not apply excessive pressure when tightening gas connections and fittings. • Do not use Teflon tape or plumber’s putty on gas flex line connections.
Installation Instructions Final Installation Re-installing the Oven Door(s) 1. Peel the protective coating off of the range, including the door. 2. Measure from the floor to the countertop. Adjust the leveling legs as required to position the trim around the cooktop even with or above the countertop. 3. Locate the anti-tip foot on the back of the range and lower (turn) it until it is 1/16” (2 mm) off the floor.
Installation Instructions Installing the Burner Knobs 1. Put the knobs with the words “MAX GRIDDLE” on them A onto the inner (center burner) valve shafts. WARNING Installing the range knobs in the wrong position may result in damage to the griddle included with the range. The knobs for the center burners are marked with the maximum griddle settings. Icons on Center Burner Knobs A NOTE: When installing the knobs, align the “D” shaped opening on the back of the knob with the end of the valve shaft.
Installation Instructions Cooktop Assembly WARNING Never attempt to operate the range’s cooktop with any of the burner rings, burner caps or grates removed. • Remove the burner rings, burner caps and grates from their shipping packages. • Install the burners as shown. The location, type and size of the burners varies with the range model number. • Spill tray Crown burner Stack burner Gently set the grates on top of the spill tray. Put the legs of each grate inside the corresponding dimples.
Installation Instructions Verifying Proper Operation Installation Checklist Before operating the range, read the accompanying use and care manual completely. It contains Important safety, service and warranty information. 1. Before beginning the test procedure, ensure that all cooktop control valves are in the OFF position, and all burner rings, burner caps, and grates are properly positioned on the cooktop frame. Turn on the gas supply at the shut-off valve. 2. Check for gas leaks. 3.
Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.
