roee fools Installation Downdraft Models ERV3015 Raised Instructions Vent and ERV3615 Includes installation instructions for optional cabinet blower (Dacor model CABP3) Use these downdraft raised vents only with approved Dacor® appliances. See the installation instructions for the particular appliance model being installed to determine suitability. Part No. 107000 Rev.
Table of Contents Important Safety INStruCtiONS ...........ccceccececsrstcrsrsrsrereeenee important Information About Safety Instructions.............. Safety Symbols and Labels ........cccccccccccececeeeeeeeeneneeeees General Safety Precautions .............cccccccccccccceeeeeeeeeneneneues Product Specifications .............cscscsccececessssessnsnssseasazeseseenes Electrical Specifications ........ cc ceceseseseseteresereeeeeeeees Product DIMENSIONS ........
Important Safety Instructions Important Information About Safety Symbols and Labels Safety Instructions Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand. See Customer Service Information. DANGER Immediate hazards that WILL result in severe personal injury or death. WARNING Hazards or unsafe practices that COULD. personal injury or death. resuit in severe CAUTION Hazards or unsafe practices that COULD. personal injury. or property.damage.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when tions, including the following: »- WARNING WARNING Do not install or operate a damaged appliance. If-you receive.a damaged appliance, contact your dealer.or builder. The installer: must show the. customer the location ‘of the electrical outlet so that the customer knows where and how to disconnect power. « . Observe.all governing codes and ordinances.
Product Specifications Product Dimensions wee - ” vf 1 t 1 ‘ ' i 3” \ (78cm) | 1 : | Top cap with ZA vent own “across back —— ' . é ie) thick stiffener Te 3/16" (5mm) — 1 be-ot6" (idem) | s . Model A- Top Cap B - Chassis Number Width Width ERV3015 30” (76.2 om) 27 3/8” (69.5 cm) ERV3615 36” (91.4 cm) 33 3/8” (84.8 cm) | (DF em) , bot fg F 36 oem) 4-2 1/8" (5.4 cm) / ‘445/16 ‘(49 unless otherwise stated ~ {6.6 em) 5/16" (8 mm) ’ Tolerances: +1/16” (41.
Installation Specifications Planning the Installation Backsplash + WARNING ». Failure to install an approved blower. or proper duct work will-result-in-a back draft and/or the insufficient venting of smoke and fumes. «To reduce the risk of personal injury caused by. reaching over a hot appliance, cabinet storage space located directly above the range/cooktop should be avoided. » « * The raised vent is equipped with adjustable anchor legs to accommodate various cabinet heights.
Installation Specifications — Backsplash Front of unit Cooktop | | Cabinet blower | / | | Connection to access hole ] CABP3 cabinet blower | ¥ Blower wiring | Raised vent cabinet blower | | Wall Alf x Connection to —»: /, remote/in-line _. Blower wiring |! access hole Floor | : f Wall cap 3 1/4” x 10" 90° elbow blower | | Electrical Layout 42” min. (30.
Installation Specifications Planning the Duct Work installations with * and REMP series blowers: With ILHSF and REMP blowers, the raised vent can be configured to exhaust through the back, the bottom or either side by removing the appropriate exhaust knock-out WARNING * ILHSF To reduce the risk of fire and to properly exhaust air, shown on the facing page. be sure to duct air outside the house. or building. Do not vent exhaust air into spaces within walls or-ceilings or into.
Installation Specifications |_| ( G ft 6 1/4" mt |< 1 1/8"-»| (2.
Installation Specifications Exhaust Locations and Dimensions for CABP3 Cabinet Blower Installations 4 Model Cooktop ERV L r ul A B 42 4/8” ERV3015 (30.7 cm) ERV3615 (24.8 cm) c 5 5/8” (14.4 cm) | (4.4 cm) 4 4/4” 8” 9 3/4” 1 3/4” (20.3em) | __(10.8 cm) CABP3 ——- 8 7/8" (22.5 cm) from back of ERV cutout to center line of CABP3 exhaust in any orientation ADAPTER [< ¢ ~«—— Raised vent Countertop \ center line pA PA wz 26 1/4” (66.
Installation Specifications Calculating the Maximum Duct Run Length Duct Work Design Tips For optimal performance, consult a qualified HVAC specialist when designing the duct system. * Wherever possible, reduce the number of transitions and turns to as few sharp angles as possible. Two staggered 45° angles are better than one 90°. Keep turns as far away from the hood exhaust as possible, with as much space between each bend as possible.
Installation Instructions Installation Preparation Installation Preparation for Raised Vent with ILHSF or REMP Series Blower: Verify Package Contents 1. Unpack the raised vent and verify that all required parts have been provided. If any item is missing or damaged, please contact your dealer immediately. Do not install a damaged or incomplete appliance. The customer must report cosmetic issues within 30 days of installation.
Installation Installation Preparation for Raised Vent with CABP3 Cabinet Blower: 1. You must remove the raised vent front cover so that the AERVCAB cabinet blower adapter can be installed. To do so, remove and retain the three (3) wing nuts and three (3) flat washers on the front of the unit. Discard the three (3) lock washers (they will be replaced). Then tilt the cover out and pull up to remove it. Instructions Installing the Raised Vent in the Cutout 1.
Installation Instructions Cabinet Blower Installation ILHSF or REMP Series Blower Installation lf using cabinet blower (model CABP3): if using a ILHSF or REMP series blower, install it according to the blower installation instructions. 1. Locate the wiring diagram label included with the adapter kit. Peel the protective backing off and place it over the existing label on the CABP3 blower as shown.
Installation Instructions Match wire colors to terminals as shown. Wires to power plug. Pre-wired at factory. Do not modify. Attach ground wire Blower power wiring/conduit. as shown Connect other end of wires to blower terminal block. Front of raised vent CABP3S cabinet blower Electrical connection from raised vent, match Wire Colors Electrical access /N\ Electrical Installation - CABP3 Raised vent blower wiring access hole Cabinet Blower Wire Colors : Black = Line (L), White = Neutral (N),
Installation Instructions Verifying Proper Operation WARNING Installation Checklist L] Are the anchor legs extended down to make contact with the floor and tightened into place? Are the anchor legs fastened to the floor? Is the unit level? L] Is the duct work completely installed? Are all joints attached with sheet metal screws and wrapped with duct tape? L] Are both ends of the blower power cable connected the raised vent and to the blower itself)? L] Are the vent filters installed according to the
Technical Data ERVxx15 Raised Vent Wiring Diagram UP UMIT SWITCH DOWN UMIT SWITCH SNORKEL SWITCH C1 COM NOQ_NC RED BLUE | CHASSIS GROUND STUD WHT —i |r =|= REMOTE POT P RELAY = N COM NO L SPEED CONTROL Oy cdoOo} ORNG O©) 0 [2 0 N2 0 L1 0 0 0 Nt GND GND 0 0 0 0 BLOWER OUTPUT RED POWER INPUT 0 0 GROUND BLK CABP3 Cabinet Blower Ratings For ILHSF or REMP installation @ 120 Vac, 60 Hz. series blower ratings, see the blower instructions.
16 dacor.
dascor The Life of the Kitchen® Dacor e 14425 Clark Avenue, City of Industry, CA 91745 e Phone: (800) 793-0093 e Fax: (626) 403-3130 (LOLOL yay yea Family Owned American Made « www.dacor.
