cacor rior areal Installation Downdraft Models: Raised Instructions Vent ERV36-ER, ERV48-ER Use these downdraft raised vents only with approved Dacor® appliances. See the installation instructions for the particular appliance model being installed to determine suitability. Part No. 103106 Rev.
of Contents Important Safety INStruCtiONS .........cccceeeeesesesesereeereeees Important Information About Safety Instructions.............. Safety Symbols and Labels ..0..........ccccccccccccceeeeeeeeeeeeeeeenes General Safety Precautions .............c.cccccccecceceeeeeeeeeeenenenes Product Specifications ...........ccccccceccececceeeeeeeeeeeeneneneeeeeeeees Product DIMENSIONS ...........cccccccccseeesesseseseseeeseeeeeseseneneeeees Installation Specifications ...........
Important Safety Instructions Important Information About Safety Instructions * * Safety Symbols and Labels DANGER The Important Safety Instructions and warnings in these instructions are not meant to cover ail possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. immediate hazards.that WILL result-in severe. personal injury or death.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING Do not install or operate a damaged appliance. If you receive a damaged appliance, contact your dealer or builder. For general ventilating use only..Do not-use to exhaust hazardous.
Product Specifications Product Dimensions “7 , —~|e— ¢ jf 1/4" ~y 6 - 5/16” (8 mm) ,_ thick stiffener N (6 mm) . ' . Model Number ' , I \ ‘ \ (64mm) Chassis Width (B) ERV36-ER 36” (914 mm) 33 3/8” (848 mm) ERV48-ER 48” (1219 mm) 43 3/8” (1102 mm) an 20F088 Bae ' ‘| Top Cap Width (A) T \ vont down ‘ ith Tolerances: +1/16”, (1.6 mm) unless otherwise stated ; 115/16" ‘ ' (49 mm) / 4 .. 2 9/16" —>{ (65mm) ’ / + Y - le A | .
Installation Specifications WARNING *---Observe.all governing codes and-ordinances during planning and installation. Contact-your local building department for further information. * The electric outlet for the raised -vent:should be installed only by.a licensed electrician. Planning the Installation General System Layout The vent system consists of the raised vent itself and a single Dacor approved remote or in-line blower (see page 8). WARNING Electrical Specifications -..
Installation Specifications * * The raised vent exhaust may be configured to vent through the back, the bottom or through one of the sides. The maximum allowable duct run must be taken into consideration when determining the layout. See Planning the Duct Work for further details. \ Y t Refer to the range installation instructions for the minimum cutout dimensions specific to the particular range 1 t \ Countertop \\ and ERV model being installed.
Installation Specifications Planning the Duct Work WARNING «To reduce the risk of fire and to properly exhaust. air, be sure.to duct-air outside the house or-building. Do not vent exhaust.air into spaces. within walls or ceilings or into attics, crawl_ spaces or garages. *-Tape-all duct joints securely.to prevent combustion by-products, smoke or odors from entering the home. will also improve system efficiency. «TO « Doing so REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK. ~.-DO.
Installation Specifications On side exhaust installations, allow five inches of space on the side for the ADT2 exhaust transition plus additional space for the duct attached to it (X). <— | ATD2 Make sure duct work does not interfere with floor joists or wall studs. xX — 5" <|¢— “d With concrete slab construction, “box-in” the duct work and blower wiring to prevent collapsing or other damage when the wet concrete is poured.
Installation Instructions Installation Preparation 2. Cut and remove the foil material inside the knock-out hole. If you fail to remove the foil, the vent will not work. Verify Package Contents 3. If the unit will vent through the bottom or side: * Product literature « Anchoring legs * 2wood * 3 wire nuts Attach the supplied ATD2 transition to exhaust location with the provided sheet metal screws.
Installation 5. Gently slide the vent into the rear of the countertop cutout with the electrical access panel toward the front. Top of vent resting on countertop Instructions Installing the Blower and Ducts 1. Install the remote or in-line blower according to the blower installation instructions. 2. Install the duct work Specifications. Use to connect and seal weight as necessary according to the Installation sheet metal screws and duct tape all of the pieces.
Installation Instructions Run the wiring/conduit line used to supply power from the raised vent to the blower parallel to the duct work. Electrical Installation WARNING *.- ELECTRIC SHOCK HAZARD -:Do.not-connect the raised vent. power plug to the electrical outlet until installation is complete. «Failure to.complete electrical connections properly may result in an electric: shock hazard or a damaged or non-functional system. Follow.the wiring diagrams carefully to ensure.a proper installation.
Installation Instructions REMP remote series blower Connect wires/conduit according to remote blower installation instructions Raised vent \ Range _—— KKK See ERV electrical access panel on facing page & CK | yyy | »y»y»y»y»y»y»»y»y»y >» yyy YW); Wiring/conduit from ERV to remote blower Example of Installation with Bottom (Side View) Exhaust Range Installation Install the range according to the range installation instructions.
Installation Instructions Verifying Proper Operation WARNING *.
Wiring Diagram DOWN UMT SWITCH UP UMIT SWITCH SNORKEL SWITCH COM - LJ COM -— COM .
dacor a The Life of the Kitchen® Dacor e 600 Anton Bivd. Suite 1000 Costa Mesa, CA 92626 « Phone: (800) 793-0093 American Made e Fax: (626) 403-3130 « www.Dacor.