Planning Guide

ManualsBrandsDacor ManualsAppliancesDacor - 5.2 Cu. Ft. Self-Cleaning Freestanding Gas Convection Range - Stainless steel

All specications subject to change without notice.

Phone: (800) 793-0093www.dacor.com

PLANNING

GUIDE

■ All maximum and minimum dimensions and clearances shown

in the diagrams below must be maintained for safe operation.

■ The range should be placed away from drafts that may be

caused by doors, windows and heating and air conditioning

outlets.

■ Avoid cabinet installations directly above the range. If cabinet

storage is to be provided above the range, the risk can be

reduced by installing a range hood that projects horizontally a

minimum of 5 inches beyond the bottom of the cabinets.

■ The range may be installed flush to the rear wall. Dacor

strongly recommends installing a non-combustible material

on the rear wall above the range and up to the vent hood or

installation of a backguard.

■ Any openings in the wall behind the appliance or in the floor

underneath it must be sealed.

■ The shaded area in the Recommended Cabinet Clearance

Dimensions figure shows the recommended locations of the

gas inlet and the electrical junction box. For replacement

purposes, the location of the existing utilities may be used

provided they do not interfere with the sides or rear of the

range.

■ The junction box and gas shut off valve must be located

so that the range can be pulled out for service while the

appliance remains connected.

■ An external, manual shut-off valve must be installed between

the gas inlet and the range for the purpose of turning on or

shutting off gas to the appliance.

The installation must allow for the following:

■ Access to the gas shut-off valve when the unit is installed.

■ Access to the remote circuit breaker panel/fuse box, when the

range is in place.

■ The gas supply piping and shut-off valve, and the electrical

junction box must be located so they do not interfere with the

range when it is installed.

Cutout tolerances: +1/16” 0” (1.6 mm)

unless otherwise stated.

RANGE + DOWNDRAFT CUTOUT

(TOP VIEW)

Cabinet Layout

10" (25.4 cm) min.

to combustible side

walls above the range

(both sides)

non-combustible

rear wall (recommended)

Backsplash

3/8" (1.0 cm)

min. for downdraft cap

clearance

Note 2

RNRP30G, RNRP36G, RNRP48G

Renaissance

30”, 36” and 48”

Gas Ranges

Document # PG05-012

Revised 08/20/15 Page 1/4

DIMENSIONS: SEE TABLE ON FOLLOWING PAGE

Summary of content (4 pages)

PAGE 1
RNRP30G, RNRP36G, RNRP48G Revised 08/20/15 Document # PG05-012 Renaissance 30”, 36” and 48” Gas Ranges Cabinet Layout ■■ All maximum and minimum dimensions and clearances shown in the diagrams below must be maintained for safe operation. ■■ The range should be placed away from drafts that may be caused by doors, windows and heating and air conditioning outlets. ■■ Avoid cabinet installations directly above the range.
PAGE 2
RNRP30G, RNRP36G, RNRP48G Revised 08/20/15 Document # PG05-012 Renaissance 30”, 36” and 48” Gas Ranges Page 2/4 PLANNING GUIDE All tolerances +1/16” -0” (+1.6 mm) unless otherwise noted. CUTOUT DIMENSIONS Range Model F G H I J RNRP30G 36” (91.4 cm) * 30” (76.2 cm) ** 30” (76.2 cm) ** 27 1/2” 30 1/2” (77.5 cm) 3 1/2” (8.9 cm) RNRP36G 42” (106.7 cm) * 36” (91.4 cm) ** 36” (91.4 cm) ** 33 1/2” (84.8 cm) 30 7/8” (78.4 cm) 3” (7.6 cm) 54” (137.2 cm) * 48” (121.9 cm) ** 48” (121.
PAGE 3
RNRP30G, RNRP36G, RNRP48G Revised 08/20/15 Page 3/4 Document # PG05-012 PLANNING GUIDE Renaissance 30”, 36” and 48” Gas Ranges + ERV Downdrafts Product Dimensions WARNING Product tolerances: +/- 1/16” (+/- 1.6 mm) unless otherwise stated Range Part Numbers • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • This appliance must be installed in accordance with the accompanying installation instructions.
PAGE 4
RNRP30G, RNRP36G, RNRP48G Revised 08/20/15 Page 4/4 Document # PG05-012 Renaissance 30”, 36” and 48” Gas Ranges PLANNING GUIDE Electrical and Gas Requirements A B BACK OF RANGE GAS SUPPLY PRESSURE REQUIREMENTS Manifold Min. Gas Gas Max. Input Pressure* Supply Type Pressure (WC) Pressure (WC) Range Model A B RNRP30G 13 1/16” to 14 3/8” (33.2 to 36.5 cm) 4 5/16” (12.16 cm) RNRP36G 13 1/16” to 14 3/8” (33.2 to 36.5 cm) 7 5/16” (18.