Installation 30-Inch Dishwasher For use with models: ED30 and ID30 Part No. 65538 Rev.
Important Safety Instructions .......................................... Important Information About Safety Instructions .............. Safety Symbols and Labels ............................................. General Safety Precautions ............................................. Product Specifications ..................................................... Preparing for Installation .................................................. Preparing the Location .....................................................
Important Information About Safety Instructions Safety Symbols and Labels The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. • Always contact the Dacor Customer Service Team about problems and conditions that you don't understand. See Customer Service Information.
General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING Do not install or operate this dishwasher if it has been damaged, dropped, has damaged electrical conduit 0r wires or is not working properly. If the product s damaged when received, immed ately contact the dea eror builder. , Use this d shwasher only for its intended PUrpose as outlined in the use and care manual.
Dimensions Tolerances: +1/16", -0, (+1.6 mm, -0) unless otherwise stated Model ED30 shown. Door style varies with model number.
WARNING observe all governing codes and ordinances during planning and insta!lati0nl contact your 10calbuilding I department for further information. I IMPORTANT:shown Followbelow all cabinet andsafe countertop dimensions to insure operation.minimum I Prepare the installation location as shown below. All minimum product dimensions be must met or exceeded (see page 3). Dimensions shown provide minimum clearances, unless otherwise noted.
Electrical Specifications Install the Plumbing The water pressure must be between 20 and 120 psi (138-827 kPa). The household hot water heater must supply a minimum of 120 °F water to the dishwasher location for best results. WARNING • The electrical outlet for the dishwasher should be installed only by a licensed electrician. • This appliance is equipped with a three prong grounding plug for your protection against possible electric shock hazards.
Verify the Package Contents NOTE: Model ID30 ships without a front panel. It is designed for the installation of an integrated front panel that matches the surrounding cabinets. • With the assistance of at least one person, remove the dishwasher from the shipping carton. Place the unit to the side of the cabinet opening. Remove all of the packing materials from inside and outside of the unit. DO NOT allow any of the shipping materials, loose screws or plastic to remain inside. Remove the racks.
WARNING Installing the Unit in the Cabinet • Do not connect the electrical, water inlet or drain until instructed to do so in the Verifying Proper Operation section. • Do not install the dishwasher unless the . electrical service provided meets the Electrical Specifications. . Care should be exercised when the appliance is installed or removed, to reduce the likelihood of damage to the power cord or hoses. A qualified technician must complete the installation of this built-in appliance.
Leveling the Dishwasher (Continued) 3. Remove the toe kick mounting plate to expose the front legs. To adjust the front leveling legs, place a wrench on the top of each leg and adjust where the top of the dishwasher tank front trim is flush L_ Attaching the Anti-Tip Brackets H CAUTION Make sure to anchor at least one anti-tip bracket on each side of the dishwasher. II with the lower edge of the countertop. • The anchoring material must be no more than 114" (6 mm) from the anti-tip bracket.
Cabinet Panel Installation 1/2" (13 mm) _!_ (Model ID30 Only) CAUTION • To prevent corrosion and the possibility of the panel falling off, use only stainless steel screws to attach. • The provided mounting screws are designed for panels with a thickness of 5/8" to 3/4". Smaller panels may require different mounting hardware to prevent damage to the outside surface.
Plumbing Connections . . WARNING • ° For proper dishwasher operation drain line must be routed through cabinet and up to the drain or air drain hose or air gap outlet must sink trap. and drainage, the the bottom of the gap connection. The connect above the . Connect the water supply hose from the dishwasher to the hot water supply valve. Connect the flexible drain line to the air gap or directly to the drain tee or disposal above the sink trap as shown below. Tighten the holding clamp.
[] You should hear the dishwasher drain and then begin to fill with water. Wait approximately two (2) minutes, then carefully open the door to verify water is filling the dishwasher tank. If there is water present, close the door and continue the process. Should the water not fill the tank or the pump is not running, immediately push the START/STOP button to stop the dishwasher. Verify that the water supply valve is turned on, power is connected, and that main power supply is on.
Toe Kick Installation Adjusting Kick and Installing the Included Toe The the height and depth of the included toe kick are adjustable. 1. Adjust the toe kick height. The typical toe kick height is 4" high. For other than a typical installations, remove the rear assembly screws that hold the two toe kick sections together. Adjust the toe kick sections to match your desired toe kick height and reinstall the assembly screws. 2. Snap the toe kick into the toe kick mounting plate.
® The Life of the Kitchen? Dacor • Phone: (800)793-0093 • FAX: (626)403-3130 • www.Dacor.