Installation Instructions Epicure ® 30 - Inch Dishwasher For use with models: ED30, ID30 Part No. 65538 Rev.
All specifications are subject to change without notice. Dacor ® assumes no liability for changes to specifications. © 2007 Dacor, all rights reserved.
Table of Contents Before You Begin............................................................... 1 Important Safety Instructions........................................ 1-2 Product Specifications...................................................... 3 Dimensions....................................................................... 3 Technical........................................................................... 3 Preparing for Installation................................................
Important Safety Instructions To reduce the risk of fire, electric shock, serious injury or death when using the dishwasher, follow basic safety precautions, including the following: WARNING 1. Do not install or operate this dishwasher if it has been damaged, dropped, has damaged electrical conduit or wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder. 2.
Product Specifications Dimensions Tolerances: +1/16”, -0, (+1.
Preparing for Installation WARNING Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Planning the Location Carefully check the location where the dishwasher is to be installed. Place it in a location with convenient access. Make certain that electrical power can be provided in the selected location. IMPORTANT: Follow all cabinet and countertop minimum dimensions shown below to insure safe operation.
Preparing for Installation Power Supply Install the Plumbing WARNING • Install a water supply valve for the hot water supply line where it is easily accessible after the dishwasher is installed. • The water pressure must be between 20 and 120 psi (138-827 kPa). The household hot water heater should supply a minimum of 120°F water to the dishwasher location for best results. • Use the supplied flexible braided water line to connect between the dishwasher hot water inlet and the hot water supply valve.
Installation Instructions Verify the Package Contents NOTE: Model ID30 ships without a front panel. It is designed for the installation of an integrated front panel that matches the surrounding cabinets. • With the assistance of at least one person, remove the dishwasher from the shipping carton and place the unit to the side of the cabinet opening. • Using caution, remove all of the packing materials from inside and outside of the unit.
Installation Instructions WARNING • Do not connect the electrical, water inlet or drain until instructed to do so in the Verifying Proper Operation section. • Do not install the dishwasher unless the electrical service provided meets the dishwasher specifications. • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • A qualified technician must complete the installation of this built-in appliance.
Installation Instructions Leveling the Dishwasher (continued) Install the Anti-Tip Brackets 4. To adjust the rear leveling legs, rotate the #2 Phillips drive shafts, located at the toe-kick, to level the dishwasher from front to back and left to right. caution • Make sure to anchor at least one anti-tip bracket on each side of the dishwasher. • The anchoring material must be no more than 1/4” (6mm) from the anti-tip bracket.
Installation Instructions Cabinet Panel Installation (Model ID30 Only) CAUTION • The provided mounting screws are designed for panels with a thickness of 5/8” to 3/4”. Smaller panels may require different mounting hardware to prevent damage to the outside surface. • To prevent corrosion and the possibility of the panel falling off, use only stainless steel screws where instructed.
Installation Instructions Water Line Connection warning • Any solder connections must be made before the dishwasher water line is connected. Do not solder within six inches of the inlet valve. Create loop and fasten to under side of cabinet Connect the hot water line from the dishwasher to the hot water supply valve. Drain Line Installation 1. Connect the flexible drain line to the air gap (see below) or connect it directly to the waste tee or disposal (see the following page). 20" Min. 2.
Installation Instructions Final Electrical Installation Verifying Proper Operation WARNINGS WARNING • To avoid electrical shock or fire hazard, make sure the power supply at the fuse or junction box is turned off before proceeding with the final electrical installation. • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked and the unit is working properly.
Installation Instructions Verifying Proper Operation (Continued) □ □ □ □ □ □ □ □ □ You should hear the dishwasher drain and then begin to fill with water. Wait approximately two minutes, then carefully open the door to verify water is filling the dishwasher tank. If there is water present, close the door and continue the process.
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.