Installation 24-Inch Built-in Dishwasher For use with models: EDW24S, MDW24S Part No. 101586 Rev.
Important Safety Instructions .......................................... Important Information About Safety Instructions .............. Safety Symbols and Labels ............................................. General Safety Precautions ............................................. Installation Specifications ................................................ Product Dimensions ......................................................... Preparing the Location .....................................................
Important Information About Safety Instructions Safety Symbols and Labels The Important Safety Instructions and warnings in this manual are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. • Always contact the Dacor Customer Service Team about problems and conditions that you don't understand. [_ DANGER Immediate hazard s that WILL resu t n severe person a injury or death ..........
General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING , Many surfaces within the dishwasher achieve high temperatures. Do not touch interior surfaces or items inside the dishwasher during or immediately after use. Exercise caution when opening the door. Let hot air and steam escape before looking or reaching inside.
Product Dimensions Product tolerances: +1/16" (+1.6 mm),-0, unless otherwise stated _ 23 7/8" (606 mm) adjustible to 24 1/4" (616 mm)------_ I I H 14 5/8" (371 mm) -_ From rear to junction box 3 1/4" (83 mm) from side to 4" (102 mm) from side to water inlet junction box 12" (305 mm) --_ From rear to e water inlet/ Handle style varies with model number.
If the unit is to be placed in a corner, there must be at least 2 inches between the opened door and the wall. Preparing the Location The floor must be solid, level and all cut-out surfaces must be at right angles. The dishwasher must be secured to the adjacent cabinets using the anti-tip brackets for safety and proper operation.
If an air gap is not required, the drain hose must be installed to an inlet or waste tee above the drain trap in the household plumbing. If you connect to a sink drain, entry will need to be above the trap. Use a "Y" branch tailpiece and connector kit (not include) for this method. It includes all needed fittings and instructions. Plumbing Requirements Drain Connection IMPORTANT: A 72" drain hose is supplied with the product.
Verify the Package Contents Materials required • Cut the shipping carton open and use it as a pad beneath the dishwasher until the legs are installed. With the assistance of at least one person, place the unit to the side of the cabinet opening. • 90 ° elbow (3/8" NPT external thread on one end, opposite end sized to fit water supply) • 3 conductor wire (see electrical specifications) Remove all of the packing materials from inside and outside of the unit.
Electrical Connection WARNING • • Make sure power to the house junction box is off. 2. Cut an access hole for the wiring in the shaded area shown in the cabinet diagram below. ---kl Do not install the dishwasher unless the electrical service provided meets the dishwasher specifications (see page 4). O To avoid an electrical shock hazard, turn off power to the junction box at the circuit breaker panel or fuse box before proceeding.
Plumbing Connections Preparing the Dishwasher for Installation DO notcrossthedrain, Water and electrical linesin front IOfthe WARNING dishwashermotor or framel 1. Uncoil the drain hose in the back of the dishwasher. 2. Do not remove the rear insulation blanket. I. Cut the hotwater supplylineaccess holeinthe cabinet 3. as shown below. 4. Options for hot water line and drain line access hole location © Install the leveling legs into the holes below the red (shipping) plugs.
, Locate the foam support between the motor and the liner on the bottom of the unit. Use two hands to rotate and slide the foam down and to the left to remove it. Discard the foam. Level the Dishwasher CAUTION A level Unit is very imp0rtant for proper operati0n: Be sure to level the unit front to back and side to side. ............... , Foam support , , 4. Measure the height of the cabinet opening from the underside of the countertop to the floor.
Positioning the Unit in the Cabinet WARNING • Be careful not to pinch the wiring, hot water line and drain hose as you push the dishwasher into place. An electric shock hazard or water damage may result from pinched wires or hoses. Damage due to improper installation is not covered under the warranty. ° Do not push against the front panel with your knees while positioning the dishwasher. Failure to follow this warning could result in damage to the dishwasher and will void the warranty.
Finish the Electrical Connection Verifying Proper Operation WARNING WARNING Electric Shock Hazard - Make sure electrical power has been turned off at the circuit breaker panel or fuse box. To ensure a safe and proper installati0n the following cheCklist should be completed by the nsta!ler t0 ensure that no part of the installation has been oVerlooked and the unit is working properly Do not connect the dishwasher to the power supply until the appliance is permanently grounded.
Verifying Proper Operation, Cont. Wet Test Check List [] Turn on the main power supply. [] Program the dishwasher to run a normal wash. See the use and care manual for specific operating instructions. [] Close the door completely. [] Operate the machine through at least one fill and pump out and check the following items: 0 Make sure the water completely covers the filter. 0 Make sure all water is pumped out during the pump phase of the cycle. 0 Check connections for leaks.
Attaching , the Unit to the Adjacent Cabinets Remove the (2) plastic plugs on each side of the inside of the dishwasher frame. 2. Drill pilot holes into the adjacent cabinets for the provided mounting screws. 3. Secure the anti-tip brackets on both sides to the cabinets using the provided screws as shown. 4. Replace the plastic plugs. Adjusting the Stainless Steel Trim Plates Your Dacor dishwasher has been equipped with adjustable stainless steel side trim plates.
4# The Life of the Kitchen? Dacor • 1440 Bridge Gate Drive, Diamond Bar, CA 91765 • Tel: (800) 793-0093 • FAX: (626) 403-3130 • www.Dacor.