Install ation Instructions 24 - Inch Dishwasher Part No. 101891 Rev.
TABLE OF CONTENTS Before You Begin............................................................... 1 Important Safety Instructions........................................ 1-3 Product Specifications...................................................... 3 Technical........................................................................... 3 Dimensions....................................................................... 3 Preparing for Installation................................................
Important Safety Instructions To reduce the risk of fire, electric shock, serious injury or death when using the dishwasher, follow basic safety precautions, including the following: WARNING 1. Do not install or operate this dishwasher if it has been damaged, dropped, has damaged electrical conduit or wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder. 2.
Important Safety Instructions CAUTION Keep the factory installed high loop drain hose in place to ensure proper dishwasher operation. Do not cut, tie, strap or lower it. If it is necessary to lengthen it, install an aftermarket drain extension kit, available at most home improvement stores. Product Specifications Technical Water Pressure 20 to 120 psi (138 - 827 kPa) Water Temperature Power Requirements 120°F, minimum 15 A, 120 Vac, 60 Hz dedicated, grounded, circuit.
Preparing for Installation WARNING • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Preparing the Location Carefully check the location where the dishwasher is to be installed. Put it in a location with convenient access. Make certain that electrical power can be provided in the selected location. Plan the installation so that the appliance can be removed if service is required.
Preparing for Installation Power Supply Preparation WARNING • The electrical power supply for the dishwasher must be installed only by a licensed electrician as specified below. It is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a licensed electrician. Plumbing Preparation • The water pressure must be between 20 and 120 psi (138-827 kPa).
Installation Instructions Verify the Package Contents NOTE: Model ID24 ships without a front panel. It is designed for the installation of an integrated front panel that matches the surrounding cabinets. • With the assistance of at least one person, remove the dishwasher from the shipping carton. Place the unit to the side of the cabinet opening. • Remove all of the packing materials from inside and outside of the unit. DO NOT allow any of the shipping materials, loose screws or plastic to remain inside.
Installation Instructions WARNING • Do not install the dishwasher unless the electrical service provided meets the dishwasher specifications (see page 5). • A qualified technician must complete the installation of this built-in appliance. The owner is responsible to make sure the dishwasher is properly installed. Improper connection of the electrical wiring may create an electric shock or fire hazard and may result in damage to the dishwasher’s electrical system.
Installation Instructions Electrical Connection (Continued) 13. Feed the electric wire or cord into the utility hole in the side of the cut-out. Pull all of the slack out of the wire. If the unit is to be connected directly to the house wiring: • With power turned off at the circuit breaker or fuse box, remove the house junction box cover. • Feed the dishwasher wiring into the junction box. Secure the wire with a UL/CSA approved strain relief.
Installation Instructions Plumbing Connections 1. Connect one end of the 3/8” flexible braided fill hose to the water supply valve. 2. Route the hose through the utility access hole in the side of the appliance cut-out. Put the unconnected end of the hose over a bucket. Turn on the water to clean any debris out of the supply line and fill the hose for leak testing. Turn the valve off. 3.
Installation Instructions Installing the unit in the Cabinet (continued) NOTE: The leg nuts can be removed to make the dishwasher lower. To do so: ◊ Turn the leg until it comes out of the chassis. ◊ Remove the nut from the leg. ◊ Re-thread the leg into the chassis. ◊ Reach inside the chassis and thread the nut onto the top of the leg. 2.
Installation Instructions Drain Line Installation 1. Connect the flexible drain line to the air gap or connect it directly to the waste tee or disposal (see below). 2. For installations without an air gap, put a loop in the drain line as shown. 3. Tighten the holding clamp. For installations with an air gap check to make sure the drain line from the air gap to the disposal/drain trap is complete and that the clamps are tight. Create loop and fasten to under side of cabinet 20" Min.
Installation Instructions Verifying Proper Operation □ You should hear the dishwasher drain and then begin to fill with water. Wait approximately two (2) minutes, then carefully open the door to verify water is filling the dishwasher tank. If there is water present, close the door and continue the process. Should the water not fill the tank or the pump is not running, immediately push the START/STOP button to stop the dishwasher.
Install ation Instructions