MnstaJJation Mnstructions GJassWaJJ Mount Range PHW ModeJ Series Pa_ No. 101745 Rev.
important Safety instructions ..................................... Important Information About Safety Instructions ......... General Safety Precautions ........................................ installation Specifications .......................................... Product Dimensions .................................................... Operating Specifications ............................................. Planning the Location ................................................. Electrical Specifications ......
important information About Safety instructions Safety SymboJs and LabeJs [_ DANGER The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. o Immediate hazards that WILL result in severe persona! injury or death: .........................
General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: WARNING o Do not install or operate this hood if it has been damaged, dropped, has damaged electrical wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder.
Planning the Location WARNING o Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. The minLmum installed distance from the rear of blower unit base to the cooktop surface must be no less than 30" inches (76.2 cm), 26 inches (66.0 cm) for an electric cooktop. The minimum specified distance may be higher for the particular range or cooktop in use. Check the manufacturers specifications for the cooktop or range.
When planning new duct work, always look for the shortest, most direct route to the out- Electrical Specifications WARNING side. Venting can be done through the roof or directly through the back wall to the outside as shown. The e!ectrical serVic the range hood shou!d installed only by a licensed electrician. It is the owner's responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician.
WARNING o Do not install the range hood unless the power supply provided meets the required Electrical (see page 4). - Observe all governing codes and ordinances during installation. Contact your local building department for furLherinformation. o A qualified technician must complete the installation of this buHtdn appliance. The owner is responsible to make sure the hood is propedy installed.
JnstaJJingthe Chimney Mounting Bracket . . . Determine the vertical center line for the range hood. The center line for the hood is usually the same as the center line of the range or cooktop. Using a pencil, mark the vertical center line on the wall from where the bottom of hood will be located to where the top of the chimney will be located. Draw a horizontal line 9 inches long at 90 ° to the vertica_ center line where the bottom of the hood will be located.
If mounting the hood to brick or masonry: . Drill five 5/16" X 1 1/2" holes in the locations marked. . Insert five of the provided wall anchors into the five holes. The anchors provided are for attaching the hood to masonry or brick only. Mounting -bracket _ / / / / - / _ // /_/i _,_ c_€:_ Installing the Duct Work iMPORTANT - The installed . duct work must: Be centered on the vertical center line drawn on the . wall. Fit flush into the half circle on the chimney mount° ing.
Hanging the Blower Assembly . . . . Inside the exhaust outlet on the top of the blower assembly, there are metal or plastic damper flaps. The flaps close to help prevent back-drafts when the blower is turned off. Remove the shipping tape and make sure the flaps open and close freely before pro° ceeding. Insert two provided machine screws into the two holes above the mounting bracket on the blower assembly and tighten into place.
Electrical Connection installing the Chimney iMPORTANT: Be careful not to pinch the electrical wires while installing the chimney. WARNING - To avoid electrical shock or fire hazard, make sure the power supply at the fuse or junction box is turned off before proceeding with final installation. o Improper connection of the hood electrical wiring may create an electric shock or fire hazard and may result in damage to the hoods electrical system.
installing the Chimney (Cont.) Installing the Glass Hood 5. Carefully put the chimney over the blower assembly, taking care not to scratch the surfaces. Make sure the wiring is tucked in behind the chimney. J o peopiel 6. Lock the tabs inside the chimney bottom into the slots on the bottom of the blower assembly. stance 1. 2. Tabs on inside of chimney Lock tabs on inside of chimney into slots on blower assembly . . Slide the top of the chimney up toward the ceiling.
Verifying Proper Operation 1. Turn on power at the junction or fuse box. 2. If the control panel is not lit, turn on the main power switch located next to the light fixture on the underside of the hood. . Touch the light key again to turn the lights off. 5. Touch the blower "+" key once and release. Verify that one light is showing on the blower speed indicator and that the blower is on at low speed. .
12 J,_c_r
® The Life of the Kitchen? Dacor o 600 Anton Blvd. Suite !000 Costa Mesa, CA 92626 o Phone: (800) 793-0093 o Fax: (626)403-3!30 o www.Dacor.
