cdacor The Life of the Kitchen? Installation Glass Wall Mount Range Hood PHW Model Series Part No. 101745 Rev.
Table of Contents important Safety InStructiONns 2.00... cecsseeseeseesereeeeees important Information About Safety Instructions......... General Safety Precautions 2.0.0... cccccceccecceeeeeeees Installation Specification .occcccccccccecseesseeseeseesereneesees Product DIMENSIONS oo... ccc cece eee eeeeeeteeserereeeeeess Operating Specifications ......ccccececseceeeeeeees Planning the LOCAatiOn oo... cc cccccccsceeceeeceeeeeneenees Electrical Specifications oo...
Important Safety Instructions Important Information About Safety Symbols and Labels Safety Instructions * DANGER The Important Safety Instructions and warnings in Immediate hazards that WILL result in severe personal these instructions are not meant to cover ail possible injury:or-death. problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when tions, including the following: using your appliance, follow basic safety precau- WARNING Do not install or operate this hood if it has been damaged, dropped; has damaged electrical wires or-is. not working properly. [f the product is damaged:when received, immediately contact the dealer or. builder.
Installation Specifications Planning the Location WARNING « ~ Observe all- governing codes and ordinances. during planning-and installation. Contact-your local building department for further information. «. The minimum installed distance from the rear.of blower.-unit base to the cooktop surface must be no.less than 30” inches (76.2 cm), 26 inches (66.0 cm) for-an electric cooktop. The minimum specified distance may be higher. for the particular-range or cooktop in-use.
Installation Specifications Electrical Specifications * WARNING side. Venting can be The:electrical service. to the range hood should be installed only -by-a licensed electrician. it is the owner’s responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician.
Installation Instructions WARNING «Do not.install- the range hood unless the power supply provided meets the required Electrical Specifications (see page 4). «. Observe.all governing codes and ordinances during. installation. Contact your local building department for further: information. *-.-A qualified technician must complete the installation of this built-in appliance. The owner is. responsible to make sure the hood is properly installed.
Installation Instructions Installing the Chimney Mounting Bracket Installing the Blower Mounting Bracket 1, 1, Determine the vertical center line for the range hood. The center line for the hood is usually the same as the center line of the range or cooktop. Using a pencil, mark the vertical center line on the wall from where the bottom of hood will be located to where the top of the chimney will be located.
Installation Instructions °five the5/16”hoodX if mounting to brick or masonry: * 7 1/2” holes in the * Drill marked. Ylocations ° Installing the Duct Work IMPORTANT Insert five of the provided wall anchors into the five holes. The anchors provided are for attaching the hood to masonry or brick only. Mounting bracket * - a ao Be centered on the vertical center line drawn on the * wall.
Installation Instructions Hanging the Blower Assembly WARNING Do not use screws to attach the duct work to the hood exhaust outlet. Use duct tape only. Screws may prevent the damper flaps on the top of the hood from opening. 1, 3. Insert two provided machine screws into the two holes above the mounting bracket on the blower assembly and tighten into place. 4. Insert two machine screws through the front of the mounting bracket and tighten into place. 5.
Installation Instructions Installing the Chimney Electrical Connection IMPORTANT: Be careful not to pinch the electrical wires while installing the chimney. WARNING «To avoid electrical shock or-fire hazard, make sure the power-supply at the fuse or junction box is turned off before proceeding with final installation. «Improper connection ofthe hood electrical wiring may create an electric shock or fire hazard and may result in damage to.the hoods electrical system.
Installation Instructions Installing the Chimney (Cont.} 5. Carefully put the chimney over the blower assembly, taking care not to scratch the surfaces. Make sure the wiring is tucked in behind the chimney. Lock the tabs inside the chimney bottom into the slots on the bottom of the blower assembly. nstalling the Glass Hood WARNING Attaching-the.glass range hood requires two people. Do not attempt to lift the hood without assistance. 1, z. Locate the hood mounting hardware.
Installation Instructions Verifying Proper Operation 1. Turn on power at the junction or fuse box. 2. if the control panel is not lit, turn on the main power switch located next to the light fixture on the underside of the hood. Touch the light key. Verify that all the lights come on. Touch the light key again to turn the lights off. Touch the blower “+” key once and release. Verify that one light is showing on the blower speed indicator and that the blower is on at low speed.
12 decor.
dacor The Life of the Kitchen® Dacor e 600 Anton Bivd. Suite 1000 Costa Mesa, CA 92626 e Phone: (800) 793-0093 e Fax: (626) 403-3130 « www.Dacor.
