P r e f e r e n c e ™ W all For use with models: PHW301 PHW361 Part No. 101745 Rev.
Table of Before You Begin............................................................... 1 Important Safety Instructions........................................ 1-3 Product Specifications...................................................... 3 General Specifications...................................................... 3 Dimensions....................................................................... 3 Preparing for Installation................................................ 4-5 Verify Package Contents.
Important Safety Instructions To reduce the risk of fire, electric shock, serious injury or death when using your range hood, follow basic safety precautions, including the following: WARNING 1. Do not install or operate this hood if it has been damaged, dropped, has damaged electrical conduit or wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder. 2. Use this range hood only for its intended purpose as outlined in the use and care manual.
Important Safety Instructions WARNING 22. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE: a. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. b. NEVER PICK UP A FLAMING PAN - you may be burned. c. DO NOT USE WATER, including wet dish cloths or towels - a violent steam explosion may result. d.
Verify Preparing the Package Contents for Installation Unpack the parts box and verify that all required components have been provided. If any item is missing or damaged, please contact the dealer immediately. Do not install a damaged or incomplete appliance.
Preparing Electrical Power Supply for Installation • When planning new duct work, always look for the shortest, most direct route to the outside. Venting can be done through the roof or directly through the back wall to the outside. National Fire Protection Association 1 Batterymarch Park Quincy, Massachusetts 02269-9101 • Make sure duct work does not interfere with floor joists or wall studs. This hood requires a dedicated 120VAC, 60Hz, 15A circuit.
Installation Instructions WARNING • Do not install the range hood unless the electrical service provided meets the range hood specifications. • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • A qualified technician must complete the installation of this built-in appliance. The owner is responsible to make sure the hood is properly installed.
Installation Instructions Install 5. Drill the mounting holes... If mounting the hood to brick or masonry: • Drill five 5/16” X 1 1/2” holes in the locations marked. • Insert five of the provided wall anchors into the five holes. The anchors provided are for attaching the hood to masonry or brick only. MOUNTING BRACKET the Duct Work IMPORTANT - The installed duct work must: • Be centered on the vertical center line drawn on the wall.
Hanging Installation Instructions the Blower Assembly warning • Do not use screws to attach the duct work to the exhaust outlet. Use duct tape only. Screws may prevent the damper flaps on the top of the hood from opening. 1. Inside the exhaust outlet on the top of the blower assembly, there are metal or plastic damper flaps. The flaps close to help prevent back-drafts when the blower is turned off. Before hanging the blower assembly, make sure the flaps open and close freely. 3.
Installation Instructions Electrical Connection WARNINGS • To avoid electrical shock or fire hazard, make sure the power supply at the fuse or junction box is turned off before proceeding with final installation. • Improper connection of the hood electrical wiring may create an electric shock or fire hazard and may result in damage to the hoods electrical system. • Do not ground the hood to the neutral (white) power supply wire.
Installation Instructions Chimney Installation (cont.) 5. Carefully put the chimney over the blower assembly, taking care not to scratch the surfaces. Make sure the wiring is tucked in behind the chimney. 6. Lock the tabs inside the chimney bottom into the slots on the bottom of the blower assembly. Install the Hood warning • Attaching the glass range hood requires two people. Do not attempt to lift the hood without assistance. 1. Locate the hood mounting hardware.
Installation Instructions Verify Proper Operation 1. Turn on power at the junction or fuse box. 2. If the control panel is not lit, turn on the main power switch located next to the light fixture on the underside of the hood. Installation Checklist WARNING • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. • Proper installation is the responsibility of the homeowner.
Notes 12
Specifications contained within are subject to change without notice. No liability is assumed by Dacor ® for changes in specifications. The information and images in this book are the copyright property of Distinctive Appliances, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Distinctive Appliances, Inc. Web Site: Phone: www.Dacor.com (800) 793-0093 ©2006 Distinctive Appliances, Inc.
