Installation Instructions Epicure® and Millennia™ Wall Mount Range Hoods For use with models: EH30, EH36, EH42, EH48, EH54, MH30, MH36 and MH48 ® Approved for use with all dacor ranges and cooktops. Tested in accordance with the latest edition of ANSI/UL 507 standard for electric fans and can/csa-c22.2 no. 113 standard for fans and ventilators. Part No. 102139 Rev.
Table of Contents Important Safety Instructions........................................... 1 Important Information About Safety Instructions............... 1 General Safety Precautions.............................................. 2 Product Specifications ..................................................... 3 General Specifications...................................................... 3 Dimensions....................................................................... 4 Product Specifications...............
Important Safety Instructions Important Information About Safety Instructions • • Safety Symbols and Labels DANGER The Important Safety Instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service Team about problems and conditions that you don’t understand.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following: warning 1. Do not install or operate this hood if it has been damaged, dropped, has damaged electrical wires or is not working properly. If the product is damaged when received, immediately contact the dealer or builder. 2.
Important Safety Instructions warning 21. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE: a. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. b. NEVER PICK UP A FLAMING PAN - you may be burned. c. DO NOT USE WATER, including wet dish cloths or towels - a violent steam explosion may result. d.
Product Specifications Dimensions Tolerances: +1/16”, -0 (1.6 mm, -0), unless otherwise stated. NOTE: The exhaust duct(s) and electrical wiring can be connected from either the top or the back of the hood. Single exhaust models** Standard 8” duct connection Dual exhaust models* Standard 8” duct connection Front of hood Electrical access holes 7/8” Dia. (5.1 cm) 6 1/8” (15.6 cm) 1 ½” (3.8 cm) 4” (10.2 cm) 3” (7.6 cm) CL 9 7/8” (25.1 cm) 19 ¾” (50.2 cm Top Dimensions 3” (7.6 cm) 4” (10.
Product Specifications OVERALL DIMENSIONS 11 7/8” (30.2 cm) Model A C B Overall Dimensions 2” (5.1 cm) A B EH3012 29 7/8” (75.9 cm) EH3612 EH4212 35 7/8” (91.1 cm) 26 7/8” 41 7/8” (106.4 cm) (68.3 cm) EH4812 47 7/8” (121.6 cm) MH3012 29 7/8” (75.9 cm) MH3612 35 7/8” (91.1 cm) MH4812 47 7/8” (121.6 cm) EH3018 29 7/8” (75.9 cm) EH3618 35 7/8” (91.1 cm) EH4218 41 7/8” (106.4 cm) EH4818 47 7/8” (121.6 cm) EH5418 53 7/8 (136.8 cm) MH3018 29 7/8” (75.9 cm) MH3618 35 7/8” (91.
Planning the Installation warning Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Cabinet Layout important See the diagram for minimum installed distance from the hood to the cooktop surface. The minimum specified distance may be higher for the particular range or cooktop in use. Check the manufacturers specifications for the cooktop or range.
Planning the Installation Calculating the Maximum Duct Run Length warning • • To prevent combustion by-products, smoke or odors from entering the home and to improve efficiency, tape all duct joints securely. • Use only duct work constructed of materials deemed acceptable by state, municipal and local codes. • Range hoods may interrupt the proper flow of smoke and combustion gases from furnaces, gas water heaters and fireplaces.
Preparing for Installation Verify the Package Contents Unpack the parts box and verify that all parts have been included according to the parts list on page 5. If any item is missing or damaged, please contact the dealer immediately. Do not install a damaged or incomplete appliance. Make sure you have everything necessary for proper installation before proceeding. Mounting Location Preparation warning • The electrical service to the range hood should be installed only by a licensed electrician.
Preparing for Installation Ceiling or cabinet bottom Back wall Duct Cut-Out for Top Venting Duct Cut-Out for Rear Venting Installation Instructions warning • • • Blower Rotation Instructions Do not install the range hood unless the electrical service provided meets the range hood specifications. MODEL SEE PAGE EH3012, MH3012, EH3612, MH3612, EH4212 10 Observe all governing codes and ordinances during installation. Contact your local building department for further information.
Installation Instructions Rotating the Blower for Models: 8. Disconnect the wiring harness connector from the blower motor. EH3012, MH3012, EH3612, MH3612 and EH4212 (Models that are 12 inches high equipped with a single blower) 9. While supporting the blower from below, remove the four (4) nuts that hold the blower and mounting plate in place. Remove the blower from the hood. 1. Place the hood assembly on a large flat surface. 2.
Installation Instructions 13. Insert the opening on the blower motor assembly into the hole inside the back of the hood. The connector on the motor must be toward the bottom of the hood. Attach it using four (4) nuts. 17. Tip the hood back down so that the top of the hood faces up. Using existing screws, attach the cover plate removed in step 3 to the top of the hood to cover the hole. 18. Attach the duct collar removed in step 2 to the back of the unit using four (4) existing screws.
Installation Instructions 4. Tip the hood back, so that it lays on its back with the front pointing up. 5. Remove the filters from the under side of the hood. 6. Locate the wiring harness. Cut the cable tie that takes up the slack in the cable. It is located behind the panel on the right side inside the hood. Also cut the two (2) cable ties that hold the wiring harness to the brace inside the hood, on the right side. See below. 7.
Installation Instructions 14. Route the wiring harness as shown below. Secure the harness to the motor assemblies using the cable clamps supplied with the hood in the positions shown. 15. Attach the wiring harness to the brace inside the hood, on the right side using two (2) supplied cable ties. 16. Use a cable tie to take up any remaining slack that may exist in the wiring harness. Stow the harness behind the plate on the right side. Securing any slack will reduce additional noise due to vibration.
Installation Instructions 8. Disconnect the wiring harness connector from the blower motor. 9. While supporting the blower from below, remove the four (4) nuts that hold the blower in place. Remove the blower from the hood. 11. Route the wiring harness as shown. Secure the harness to the motor assembly with the cable clamps supplied with the hood in the positions shown below. 12. Attach the wiring harness to the brace inside the hood on the right side using two (2) supplied cable ties. 13.
Installation Instructions Rotating the Blower for Models: 8. Disconnect both wiring harness connectors from the blower motors. EH4818, MH4818 and EH5418 (Models that are 18 inches high equipped with two blowers. 9. While supporting each blower from below, remove the four (4) nuts that hold each blower in place. Remove both blowers from the hood. 1. Place the hood assembly on a large flat surface. 2. Remove and save the screws and the two (2) duct collars from the top of the unit. 3.
Installation Instructions 11. Route the wiring harness as shown. Secure the harness to the motor assemblies using the cable clamps supplied with the hood in the positions shown below. 12. Attach the wiring harness to the brace inside the hood, on the right side using two (2) supplied cable ties. 13. Use a cable tie to take up any remaining slack that may exist in the wiring harness. Stow the harness behind the plate on the right side. Securing any slack will reduce additional noise due to vibration.
Installation Instructions 12” high models with rear exhaust: Center the transition over the duct collars while resting the unmodified edge on the top of the hood. Fasten in place using sheet metal screws (not included). Seal the base of of the transition with duct tape. 3. Find the temporary mounting bracket in the shipping box. Put the bracket against the wall and line up the center hole with the intersection of the bracket center lines on the wall.
Installation Instructions Hanging the Range Hood Duct Work Installation warning warning Hanging the range hood requires two people. Do not attempt to lift the hood without assistance. 1. Remove the plastic coating from the outside of the hood. 2. Remove the filter(s) to reduce weight and avoid damage. 3. Lift the hood up on both sides and slip the mounting slots over the tabs on the mounting brackets. 4.
Installation Instructions Final Electrical Installation warning • To avoid electric shock or fire hazard, prior to connecting the electrical wiring to the hood, make sure that power to the hood power supply line is turned off at the fuse box or circuit breaker panel. • Improper connection of the hood electrical wiring may create an electric shock or fire hazard and may result in damage to the hood’s electrical system. See page 6 for specifications.
Installation Instructions warning • Do not ground the circuit to a gas line. • Do not ground the circuit to a hot water pipe. • Water lines that are insulated must be jumped to assure continuity to ground. See below. To house circuit breaker panel or fuse box Wire Nut, 3 places Separate No. 10 (minimum) copper ground wire WHITE WHITE GREEN GREEN Fasten clamp tightly on pipe BLACK BLACK Meter No.
Installation Instructions Verifying Proper Operation Feature Keys Installation Checklist warning Main Power Switch • To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. • Proper installation is the responsibility of the homeowner. The importance of proper installation of your Dacor range hood cannot be overemphasized.
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.