CONTACT INFORMATION Website : http://www.e-daewoo.com Call : 1-877-393-7823(1-877-DWESVC3) Washing Machine OWNER'S Manual DWD-WD33WS / SS / RS Features ■ Economic wash system With artificial intelligence, the washer uses minimum energy and water by selecting optimal water level and washing time. ■ Low noise system The washer minimizes the washing and spinning noises by sensing the amount of laundry.
IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life IMPORTANT SAFETY INSTRUCTIONS WARNING! - To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following : 1. Read all instructions before using the appliance. 2.
PARTS AND FEATURES The parts and features of your washer are illustrated on the page. Become familiar with all parts and features before using your washer. NOTE The drawings in the book may vary from your washer model. They are designed to show the different features of all models coverd by this book, So your model may not include all the features.
INSTALLATION INSTRUCTIONS Removing transit bolts 1. Before operating the washer, remove the transit bolts(4ea) along with the rubber. •If the bolts are not removed, it may cause heavy vibration, noise and malfunction. 2. Unscrew the 4 bolts with the spanner supplied. Keep the 4 bolts and spanner for future use. •Whenever the appliance is transported, the transit bolts must be refitted. 3. Close holes with supplied cap holders. Location of your washer • Check location where the washer will be installed.
Connecting water supply hose (Connect to the water valve of the washer) • Water supply pressure must be between 4.5 and 145 PSI (30~1000 kPa). • Do not crossthread when connecting inlet hose to the valve. If the water supply pressure is more than 145 PSI, a pressure reducing device should be installed. • Two Sealing washers are supplied with the water inlet hoses to prevent water leaks. • Check for leakage of washing machine connections by turning the tap completely on.
Positioning the washer ■ Installation Clearances ■ Minimum clearances for closet installation • Washer dimensions • Closet installations require a minimum clearance. Sides - 1 in(2.5cm) Rear - 1 in(10.2cm) Top - 32 in(81.3cm) .9" 40 cm) 4 (10 3" (7.6cm) 48 in.2* (310 cm2) 40.1 (102cm) 31.8 (80.9cm) 27 (68.6 " cm 24 in.2* (155 cm2) 3" (7.6cm) ) • The location must be large enough to fully open the washer door. • Most installations require a minimum clearance. Sides - 1 in(2.5cm) Rear - 4 in(10.
31.8" (80.9cm) 1" (2.5 cm) 1" (2.5 cm) [Side view] ■ Level floor • Allowable slope under entire washer is 1°. • To minimize noise and vibration, the washer MUST be installed on a solidly constructed floor. • Carpeting and soft tile surfaces are not recommended. • Never install the washer on a platform or weakly supported structure NOTE: A firm, solid floor is even more critical to a front-loading washer than to a top-loader. If your floor is wood and/or frame construction, you may need to reinforce it.
INSTALLATION OF ACCESSORIES *Please be sure to read and follow the installation operation manual. (Pedestal Model : P-W151W) CAUTION : When installing the said product, please be sure to let the expert with electrictiy & machine related training and sufficient experiences install it. People's safety is the first priority. There are many safety particulars in the guidebook and product. Therefore, please be sure to read and abide by all safety particulars. 6.
* Please be sure to read and follow the installation operation manual(Stacking Kit Model : K-ST1*) CAUTION : When installing the said product, please be sure to let the expert with electrictiy & machine related training and sufficient experiences install it. 4. Push and fix the front and rear bracket of the stacking kit as shown in the picture. People's safety is the first priority. There are many safety particulars in the guidebook and product.
OPERATING YOUR WASHER To obtain the best washing results, you must operate your washer properly. This section gives you this important information. Preparing clothes for washing • Close zippers, snaps, and hooks to avoid snagging other items. Remove pin, buckles, and other hard objects to avoid scratching the washer interior. • Empty pockets and pull them inside out. • Turn down cuffs and turn synthetic knits inside out to avoid pilling. • Tie strings and sashes to avoid tangling.
Loading • Drop items into washer loosely. Items should move easily through wash water for best cleaning and wrinkle-free results. • Load washer properly and select correct load size setting. Overloading and selecting a setting too small for the wash load can : - Cause poor cleaning - Increase wrinkling - Create excessive lint - Wear out items faster (because of pilling) • Mix large and small items in each load. Load evenly to maintain washer balance.
USING THE DISPENSER The automatic dispenser consists of four compartments which hold 1) liquid chlorine bleach, 2) liquid fabric softener, 3) liquid or powdered detergent for prewash and 4) liquid or powdered detergent and color safe bleach for main wash. All laundry products can be added at once in their respective dispenser compartments. They will be dispensed at the appropriate time for most effective cleaning. After loading the laundry additives into the dispenser, close the dispenser drawer.
2. Main Wash Detergent Compartment 3. Liquid Bleach Compartment • Add measured detergent to this compartment for Main wash. Detergent is flushed from the dispenser at the beginning of the cycle. Either powdered or liquid detergent can be used. • Add measured liquid chlorine bleach to this compartment. The bleach will be automatically dispensed at the proper time during the wash cycle. • Do not exceed the maximum fill line.
THE FUNCTION OF CONTROL PANEL Press this switch to turn the power “ON” or “OFF”. Operation and temporary stop is repeated as it is pressed. When you want to change program in operating; Press the “Start / Pause” button → Select the program that you want to change → Press the “Start / Pause” button again. You can select the course you want and each lamp is turned on when that course is selected. You can select the wash/rinse course you want and each lamp is turned on when that course is selected.
If can be used to pre-engaged in for wash 1 hour to 12 hours. use to memorize frequently used program To make a Custom Program. 1. Select a cycle. ('18:88'or'CEP' will be showen by turns) 2. Select Wash/Rinse Temperature, Spin Speed, and Soil Level. 3. Select other desired Options. 4. Press Start/Pause Button. Use this function when you want to protect any accident occurring from handling of washer by a child. During an operation of washer, press 'BEEPER' buttons simultaneously during 3 second.
WASHING PROGRAM Program Fabric type Proper Temp. Default data Maximum Load White First check whether laundry is machine washable. (white cotton, linen, towel and sheets..) Warm / Cold Wash: main wash Rinse: 2 Spin: Medium soil level : light Refer to rating label Wool Machine washable woolens with pure new wool only Cold / Cold Wash: main wash Rinse: 1 Spin: Low soil level : light Refer to rating label Delicated laundry easily damaged. (silk, curtains,..
Program Soak White Delay Wash PreWash Extra Wash Extra Rinse Rinse +Spin Night Time O O O O O O O O O O O O Wool Delicate O Permpress O O O O O O Cotton O O O O O O Normal O O O O O O Heavy Duty O O O O O O O O O O O O O O O O O O Bulk Sanitary O Speed wash O Drun Cleanign O 17
WASHING PROCEDURE AND SELECTION 1. WHITE PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. 2 Press the Power button. • The LED shows only ‘- --’ signal.
2. WOOL PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) in the detergent case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. 2 Press the Power button. • The LED shows only ‘- --’ signal. 3 Select the ‘WOOL’ program using the program selection dial.
3. DELICATE PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Liquid detergent, Softner and Bleach should be below ‘MAX‘ level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. 2 Press the Power button. • The LED shows only ‘- --’ signal.
4. PERM PRESS PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. 2 Press the Power button. • The LED shows only ‘- --’ signal.
5. COTTON PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergernt case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. • Put the detergent into the pre wash room (I marking) only if you want to add prewash. 2 Press the Power button. • The LED shows only ‘- --’ signal.
6. NORMAL PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergernt case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. • Put the detergent into the pre wash room (I marking) only if you want to add prewash. 2 Press the Power button. • The LED shows only ‘- --’ signal.
7. HEAVY DUTY PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. 2 Press the Power button. • The LED shows only ‘- --’ signal.
8. BULKY / LARGE PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergernt case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. • Put the detergent into the pre wash room (I marking) only if you want to add prewash. 2 Press the Power button. • The LED shows only ‘- --’ signal.
9. SANITARY PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergernt case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. • Put the detergent into the pre wash room (I marking) only if you want to add prewash. 2 Press the Power button. • The LED shows only ‘- --’ signal.
10. SPEED-WASH PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) in the detergent case. • Liquid detergent, Softner and Bleach should be below ‘MAX’ level. 2 Press the Power button. • The LED shows only ‘- --’ signal. 3 Select the ‘Speed-wash’ program using the program selection dial.
11. DRUM CLEANING PROGRAM 1 Press the Power button. • The LED shows only ‘- --’ signal. 2 Select the ‘DRUM CLEANING’ program using the program selection dial. • If you press ‘Start/Pause’ button aftrer pressing Power button without selecting program, the ‘Normal’ program is selected as default program. • ‘Cold/Cold’ water temperature and ‘soak’ washing course and ‘2’ times rinse and ‘Low’ spin speed are selected automatically. 3 Press the ‘Start/Pause’ button.
GUIDE FOR OTHER USEFUL PROGRAMS DELAY WASH 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below ‘MAX’ level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent.
CUSTOM PROGRAM 1 Put the laundry into the Drum and put the detergent and softerner into the detergent case. Then close the Door. • Put the detergent into the main wash room(I I marking) and prewash room(I marking) in the detergent case. • Softener should be below ‘MAX’ level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. 2 Press the Power button.
RINSE+SPIN 1 Put the laundry into the Drum and put softerner into the detergent case. Then close the Door. • Softener should be below ‘MAX’ level. 2 Press the Power button. • The LED shows only ‘- --’ signal. 3 Select the program you want using the program selection dial. • If you press ‘RINSE+SPIN’ button without selecting program, the ‘Cotton’ program is selected as default program. 4 Press the ‘RINSE+SPIN’ button.
MAINTENANCE Proper care of your washer can extend its life. This section explains how to care for your washer properly and safely. Cleaning your washer Exterior Interior Wipe up detergent, bleach, and other spills with a soft, damp cloth or sponge as they occur. Occasionally wipe the outside of the washer to keep its looking like new one. Clean interior with 250ml of chlorine bleach mixed with 500ml of detergent. Run washer through a complete cycle. Repeat this process if necessary.
HOW TO CLEAN THE FILTER Cleaning the water inlet filter Clean the filter when water leaks from the water inlet. ① Pull the power plug out before cleaning it. ② Turn off the water supply to the washer and separate the inlet hose. ③ Pull the inlet filter out. ④ Remove the dirt from the inlet filter with a brush. Cleaning the drain filter • This drain filter is used to screen the foreign stuffs such as threads, coins, pins, buttons etc..
REMOVING STAINS Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results. Soaking helps remove protein-type stains like blood, milk or grass. Prewashing helps loosen soil before washing. Stain removal rules • Use warm water for soaking or prewashing stained laundry. Hot water can set stains. • Most stains are easier to remove when they are fresh.
TROUBLE SHOOTING Most problems are easily solved if you understand the cause. Check the following list for problem before calling for service. If the error mode such as IE, OE, UE were displayed on the control part, in order to solve these problem, first turn off the power of the washing machine and then turn on the power pressing Power button.
SPECIFICATION MODEL DWD-WD33WS / SS / RS Dimensino (Inches) 27 x 31.8 x 40.1 (W x D x H) (Door open D : 40.9) Unit Weight (lbm) 198.4(Net) / 227(Gross) Spin Speed (RPM) 1200 RPM Operating Water Pressure 4.5~145 PSI (30~1000 kPa) Wash capacity 3.8 cu.ft. DOE Electrical Spec.
DAEWOO WASHER LIMITED WARRANTY Your DAEWOO will be will repaired or replaced, at DAEWOO's option, if it proves to be defective in material or workmanship under normal use, during the warranty period ("Warranty Period") set forth below, effective from the date ("Date of Purchase") of original consumer purchase of the product. This limited warranty is good only to the original purchaser of the product and effective only when used in the United States, including Hawaii, and U.S. Territories.
ABOUT THIS MANUAL VISION CREATIVE, INC. 서울 종로구 통의동 6번지 이룸빌딩 4층 담 당 배상일 대리님 브 랜 드 DAEWOO 언 F. MODEL 미주향 Washer MANUAL B. MODEL DWD-WD33WS / SS / RS 어 영어 쇄 애드컴 1차 2차 일 정 3차 4차 5차 제 판 인 한 MEMO 접수: (총 37p) 10.02.10-표지, 36p_ 신규 2p 10.05.10-표지, 3p, 11p, 36p 수정_ 신규 4p 11.07.11-표지, 36p 수정_ 신규 2p 11.07.